NEC Neax 2000 Ivs2 Wcs System Manual
Have a look at the manual NEC Neax 2000 Ivs2 Wcs System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 2 INSTALLATION Mounting CSI Card NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 33 MOUNTING CSI CARD (1) Before mounting the CSI (PN-2CSIA) card, confirm the correct switch settings. SeeCHAPTER 4. (2) Mount the CSI card in the LT slots of PIM0 though PIM7. PIM0-7: LT00-LT07 slotsATTENTIONContents Static SensitiveHa ndl ing Prec au tio ns Requ ired
NEAX2000 IVS2WCS System Manual (PCS)Page 34ND-70920 (E), Issue 1.0 CHAPTER 2 INSTALLATION Connection of ZT CONNECTION OF ZT Connect the cable to a ZT via the MDF as described in this section. Location ofLT slots andLTC connectors for ZT (Figure 2-1) MDF Cross connection for ZT (Figure 2-2) Figure 2-1 Location of LT Slots and LTC Connectors for ZT LT C 0 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25RA0 TA 0 RA1 TA 1 RA0 TA 0 RA1 TA 1 RA0 TA 0 RA1 TA 1 MJRB0 TB0 RB1 TB1 RB0 TB0 RB1 TB1 RB0 TB0 RB1 TB1 MN 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT 0 0 SLOT LT 0 1 SLOT LT 0 2 SLOT LT C 1 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25RA0 TA 0 RA1 TA 1 RA0 TA 0 RA1 TA 1 RA0 TA 0 RA1 TA 1RA0 TA 0 RA1 TA 1 RA0 TA 0 RA1 TA 1 RB0 TB0 RB1 TB1 RB0 TB0 RB1 TB1 RB0 TB0 RB1 TB1RB0 TB0 RB1 TB1 RB0 TB0 RB1 TB1 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT 0 3 SLOT LT 0 4 SLOT LT 0 5 SLOT LT C 2 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT 0 8 SLOT LT 0 7 SLOT LT 0 6 SLOT LT C 3 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT 1 1 SLOT LT 1 0 SLOT LT 0 9 SLOT L T 1 1 L T 1 0 L T 0 9 L T 0 8 L T 0 7 L T 0 6 L T 0 5 L T 0 4 L T 0 3 L T 0 2 L T 0 1 L T 0 0
CHAPTER 2 INSTALLATION Connection of ZT NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 35 Figure 2-2 MDF Cross Connection for ZT CAUTION: Incorrect wiring may cause severe damage to the equipment. PBX (PIM0-7) BWB CSI TWISTED-PAIR CABLEMDF LTC0/LTC1/LTC2 CONNECTORModular Connector To Z T 1RA0 26RB0 2TA0 27TB0 3RA1 28RB1 4TA1 29TB1 5RA2 30RB2 6TA2 31TB2 7RA3 32RB3 8TA3 33TB3 934 10 35 11 36 12 37 13 38 14 39 15 40 16 41 17 42 18 43 19 44 20 45 21 46 22 47 23 48 24 49 25 50 ZT No. 0 ZT No. 1 ZT No. 2 ZT No. 3 Modular Jack (RJ-45) Modular plugTA RA TB RB ZT NOTE:Confirm that all feed polarity TA/TB and RA/RB is normal before con- necting ZT to RJ-45 Modular jack. TA/TB minus RA/RB plus MDF TA RA RB TB LTC CONNECTOR
NEAX2000 IVS2WCS System Manual (PCS)Page 36ND-70920 (E), Issue 1.0 CHAPTER 2 INSTALLATION Connection of ZT Figure 2-3 MDF Cross Connection via MDF for ZT 12 3 4 5 6 7 8 Modular Connector (8)(1) NOTE:RJ-45 Modular Jack is highly recommended. Keep all wiring straight to the jack and perform all reverses at the cross connect for future changes. TERMINAL NUMBERCOLORTERMINAL NUMBERFUNCTION POLARITY CSI TERMINAL TERMINAL EQUIPMENTCSI SIGNAL FEED 1 blue a Not used Not used 2 orange b Not used Not used 3 black c Transmission Reception + – RA 4 red d Reception Transmission + – TA 5 green e Reception Transmission – + TB 6 yellow f Transmission Reception – + RB 7 brown g Not used Not used 8 slate h Not used Not used
CHAPTER 2 INSTALLATION Installation for Multi-Site Roaming NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 37 INSTALLATION FOR MULTI-SITE ROAMING (1) Before mounting the DTI (PN-24DTA/PN-30DTC), DCH (PN-SC01), DBM (PN-AP00-A) card, set the MB switch to UP position, and set the other switches to appropriate position. SeeCHAPTER 4. (2) Mount the DTI, DCH, DBM card in AP slots of PIM0 though PIM7. PIM0-7: AP00-AP11 slots (3) After mounting the card, set the MB switch to DOWN position to put the card in service. (4) To select PLO in the MP card, set the switches of the MP card. SeeCHAPTER 4. (5) Connect the cable to a CSU via the MDF for DTI as shown inFigure 2-4. Location of AP Slots and LTC Connectors for DTI (Figure 2-5) Example of MDF Cross Connection for DTI (Figure 2-6) Figure 2-4 DTI Cable Connection via MDF CSU MDF TWISTED-PAIR CABLE BWBPBX (PIM0-PIM7) LT C 0 / LT C 1 / LT C 2 / LT C 3 CONNECTOR DTI NOTE:The CSU must be installed to interface with the network, and must be installed on the premises where the PBX is. MAX. 200 m (655 ft.) .... 24DTI MAX. 400 m (1310 ft.) .. 30DTI
NEAX2000 IVS2WCS System Manual (PCS)Page 38ND-70920 (E), Issue 1.0 CHAPTER 2 INSTALLATION Installation for Multi-Site Roaming Figure 2-5 Location of AP Slots and LTC Connectors for DTI LT C 0 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25RA TA RA TA RA TA MJRB TB RB TB RB TB MNRA TA RA TA RA TARB TB RB TB RB TBRA TA RA TA RA TARB TB RB TB RB TBRA TA RA TA RA TARB TB RB TB RB TB 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 AP00 SLOT AP01 SLOT AP02 SLOT LT C 1 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 AP03 SLOT AP04 SLOT AP05 SLOT LT C 2 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 AP08 SLOT AP07 SLOT AP06 SLOT AP11 SLOT AP09 SLOT AP10 SLOT LT C 3 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 L T 1 1 / A P 1 1 L T 1 0 / A P 1 0 L T 0 9 / A P 0 9 L T 0 8 / A P 0 8 L T 0 7 / A P 0 7 L T 0 6 / A P 0 6 L T 0 5 / A P 0 5 L T 0 4 / A P 0 4 L T 0 3 / A P 0 3 L T 0 2 / A P 0 2 L T 0 1 / A P 0 1 L T 0 0 / A P 0 0
CHAPTER 2 INSTALLATION Installation for Multi-Site Roaming NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 39 Figure 2-6 Example of MDF Cross Connection for DTI PIM 0 JP MDF PN-24DTA/PN-30DTC AP05 RA RB TA TB17 42 18 4317 42 18 43RA RB TA TBTO CSU LT C 1 RECEIVE TRANSFER 17 18 19 20RA TA42 43 44 45RB TB LT C 1 ( J )42 43 44 45RB TB17 18 19 20RA TA LT C 1 ( P )
NEAX2000 IVS2WCS System Manual (PCS)Page 40ND-70920 (E), Issue 1.0 This page is for your notes.
NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 41 CHAPTER 3 SYSTEM DATA PROGRAMMING This chapter explains the programming procedure to provide the WCS feature to the PBX.
NEAX2000 IVS2WCS System Manual (PCS)Page 42ND-70920 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING How to Read This Chapter HOW TO READ THIS CHAPTER In the programming procedure, the meaning of (1), (2), and markings are as follows. (1) : 1st Data (2) : 2nd Data : Initial Data With the system data clear command (CM00, CM01), the data with this marking is automatically assigned for each command. : A reset of the MP card is required after data setting. Press SW1 switch on the MP card. : A reset of the DBM card is required after data setting. Set the Make Busy switch to UP and then DOWN. For general description, operating procedure, service conditions of WCS features, refer to the WCS Features and Specifications. INITIAL DBM INITIAL