NEC Neax 2000 Ivs2 Wcs System Manual
Have a look at the manual NEC Neax 2000 Ivs2 Wcs System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 3 SYSTEM DATA PROGRAMMING Progamming Summary NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 43 PROGAMMING SUMMARY Perform the system data programming related to the WCS according to the following procedure. For other system data related to the PBX, refer to the Command Manual and the CCIS System Manual. Initial Setup of System V I RT UA L L I N E / T RU N K DATA PROGRAMMING END ZT AUTHORIZATION PS DATA PROGRAMMING Adjunct System (CCIS Interface) Integrated System WCS FEATURE PROGRAMMING VI RTUAL LINE /TRUNK DATA PROGRAMMING TYPE OF SYSTEM? Adjunct System ZT DATA PROGRAMMING START (Analog Interface) TRUNK DATA PROGRAMMING CCIS DATA PROGRAMMING NOTE MULTI-SITE ROAMING DATA PROGRAMMING Page 46 Page 53 Page 56 Pag e 59 Pa ge 5 6 Page 64 Page 80 MAINTENANCE DATA PROGRAMMINGPage 101 NOTE:Refer to the CCIS System Manual. By NTAC or LVP
NEAX2000 IVS2WCS System Manual (PCS)Page 44ND-70920 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING Progamming Summary Changing ZT Data in Service When you change the ZT data (CM10, CM06, CMAD, CMAE) in service, make busy of the ZT is required. In this case, do the following procedure. NOTE:To make busy or make idle the ZT in service, assign data as follows: CME5 Y=3 (1) 000-127: ZT No. (2) 1: Make idle 2: Make busy after calls finished. START END CHANGE OF ZT DATA? NO YES CHANGE OF ZT DATA (CM10, CM06, CMAD, CMAE) MAKE BUSY OF ZT (CME5 Y=3>2)* CALL NTAC INPUT THE REQUIRED DATA BY MATWorX ACCESS TO LVP SERVER CHANGE OF OTHER DATA MAKE IDLE OF ZT (CME5 Y=3>1) NOTE CHANGE OF ZT NUMBER (CM10) orFROM PC
CHAPTER 3 SYSTEM DATA PROGRAMMING Progamming Summary NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 45 Changing PS Data If you change the PS data which has been already downloaded to a PS, do PS data download again by CM1D. CM1D YY=20 (1) X-XXXXXXXX: PS station No. (2) 1 Replacing PS When replacing the PS with a new one, moreover assigning the same PS number to the new PS, delete the PS number registered to the WCS by CM1C is required before downloading the new PS data. CM1C (1) 000-255: Virtual PS LEN (2) CCC: Clear
NEAX2000 IVS2WCS System Manual (PCS)Page 46ND-70920 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING ZT Data Programming ZT DATA PROGRAMMING Initial Setup DESCRIPTION DATA Assign an AP number to the CSH card. The AP number must match the SENSE switch settings on the CSH card. (1) (2)Y=0 04-15, 20-31: AP No. 23: CSH (PN-SC03-A) card Assign a ZT number to the required LEN. NOTE:The ZT number must be assigned to the first LEN (Level 0) and/or second LEN (Level 2) of each LT slot.(1) (2)000-763: LEN 0-7 (PIM0-7) + 00-63 (Por t No.) EE 3 XXX XXX : 000-127 (ZT No.) NONE : No data CCC : Data Clear Assign a data pathbetween the CSH and the CSI. D channel Block number is used to assign the control data path between the CSH and CSI. One CSH had 4 D channel Blocks, and 1 D Channel Block controls 1 CSI. NOTE:The first LEN (Level 0) must be assigned as the 2nd data. (1) (2)YY=10 XX YY XX : AP No. assigned by CM05 (04-15, 20-31) YY : 00-03 (D Channel Block No.) X00 X08 X16 X24 X32 X40 X48 X56 NONE : No data CCC : Data Clear CM10 CM06 START CM05 A INITIAL The first LEN (Level 0) of each CSI card X: PIM No. (0-7)
CHAPTER 3 SYSTEM DATA PROGRAMMING ZT Data Programming NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 47 DESCRIPTION DATA Assign an area to be called to eachZT. NOTE:Confirm that the busy LED lamp on CSI card is flashing (60 IPM). (1) (2)YY=00 000-127 : ZT No. XX Y ZZ XX : 00-31 (Calling Area No.) Y : 0-7 (Group No.) ZZ : 00-31 (Group ZT No.) NONE : No data CCC : Data Clear Specify the type of ZT. (1) (2)YY=19 000-127 : ZT No. 00 : D termPS II Type 15 : Previous DtermPS Type Assign a PAD data to each ZT, if required. (1) (2)YY=01/08/09/10 (Connecting Patterns) 000-127 : ZT No. See the following table: T: Transmitter (PS to ZT) PAD (dB) /R: Receiver (ZT to PS) PAD (dB) +: Gain –: Loss CMAD A B 2ND DATAPA D D ATA ( T / R ) YY=01 (CSI-COT/ODT/ DID)YY=08 (CSI-DTI)YY=09 (CSI-LC/DLC)YY=10 (CSI-CSI) 00 0/0 0/0 0/0 0/0 01 0/+3 0/+3 0/+3 0/+3 02 0/+6 0/+6 0/+6 0/+6 03 0/–3 0/–3 0/–3 0/–3 04 +3/+3 +3/+3 +3/+3 +3/+3 05 +3/+6 +3/+6 +3/+6 +3/+6 06 +3/–3 +3/–3 +3/–3 +3/–3 07 –3/–3 –3/–3 –3/–3 –3/–3 08 +3/0 +3/0 +3/0 +3/0 09 +6/0 +6/0 +6/0 +6/0 10 –3/0 –3/0 –3/0 –3/0 11 –3/0 –3/0 –3/0 –3/0 12 0/–3 0/–3 0/–3 0/–3 13 0/–6 0/–6 0/–6 0/–6 15 0/0 0/0 0/+6 0/+6
NEAX2000 IVS2WCS System Manual (PCS)Page 48ND-70920 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING ZT Data Programming DESCRIPTION DATA Specify the Nation Code. (1) (2)YY=00 03 (Nation Code Assignment) 003 : North America 310 004 : North America 311 005 : North America 312 006 : North America 313 007 : North America 314 008 : North America 315 009 : North America 316 255 : Not used When providing Roaming service, assign the Network ID. (1) (2)YY=42 00 (Network ID Assignment) 00000-65534 : Network ID NONE : Invalid (No Network ID) NOTE:Network ID method is one method to operate multi-site roaming. A Roaming PS must have two SYS-IDs on the Network ID method. One is main SYS-ID for Home PBX and the other is Network ID for Roaming network. The Network ID is used to define whether the PS can operate under the control of PBXs on the Roaming network. The same Network ID must be used for all PBXs within the same network. This data must be assigned only if roaming service is provided. CMAE B C DBM INITIAL
CHAPTER 3 SYSTEM DATA PROGRAMMING ZT Data Programming NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 49 Changing ZT Data in Service When you change the ZT data (CM10, CM06, CMAD, CMAE) in service, make busy of the ZT is required. When you change the ZT number by CM10, ZT authorization is required by NTAC or LVP Server entry. DESCRIPTIONDATA Assign a Control Carrier Information. NOTE 1:Set 1st priority to the 5th priority (10 digits). NOTE 2:Select the Control Carrier No. as follows: Fo r examp le: AA: 02DD: 00 BB: 04EE : 00 CC: 06 NOTE 3:After changing CMAE Y=15, a system reset is required for the change to take effect and PS operation data must be downloaded every time the control carrier number is changed. NOTE 4:When roaming service is provided, assign the same control carrier information in all PBXs in the network. (1) (2)YY=15 (Control Carrier Information) 00 (Assignment of Carrier Priority) AA BB CC DD EE (Control Carrier No.: See below.) AA : 1st Priority BB : 2nd Priority CC : 3rd Priority DD : 00 EE : 00 Control Carrier No. (01-20) 01: 1920. 35 MHz 02: 1920. 65 MHz 03: 1920. 95 MHz 04: 1921. 55 MHz 05: 1921. 85 MHz 06: 1922. 15 MHz 07: 1923. 05 MHz 08: 1923. 35 MHz 09: 1924. 25 MHz 10: 1924. 55 MHz 11: 1925. 45 MHz 12: 1925. 75 MHz 13: 1926. 65 MHz 14: 1926. 95 MHz 15: 1927. 85 MHz 16: 1928. 15 MHz 17: 1928. 45 MHz 18: 1929. 05 MHz 19: 1929. 35 MHz 20: 1929. 65 MHz Call NTAC or get your LVP code before proceeding. END CMAE C
NEAX2000 IVS2WCS System Manual (PCS)Page 50ND-70920 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING ZT Data Programming DESCRIPTION DATA Make the ZT busy. (1) (2)Y=3 000-127 : ZT No. 2 : Make busy after calls finished. Make the ZT idle. (1) (2)Y=3 000-127 : ZT No. 1:MakeIdle CM10 CM06 CMAD START END CME5 CMAE CME5Change the ZT data. SeeInitial Setup on Pa ge 4 6
CHAPTER 3 SYSTEM DATA PROGRAMMING ZT Authorization NEAX2000 IVS2WCSSystemManual(PCS) ND-70920 (E), Issue 1.0Page 51 ZT AUTHORIZATION Initial Setup of ZT Do the following procedure to set up the ZT. NOTE:When re-installing the system after power down exceeding 8 hours, the System ID will be cleared. The System ID must be re-entered. START ZT DATA PROGRAMMING ZT AUTHORIZATION SYS ID ASSIGNMENTASSIGNMENT OF LVP CODE END ZT AUTHORIZATION NTAC LV P Pag e 46 Call NTAC or enter the System ID code on MATWorX Studio. Please call NTAC (National Technical Assistance Center) for this data assignment. Action by Maintenance Person : :
NEAX2000 IVS2WCS System Manual (PCS)Page 52ND-70920 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING ZT Authorization Setting Up of Additional ZT Do the following procedure to add the ZT. START ZT DATA PROGRAMMING ZT AUTHORIZATION END See MATWorX Studio.Pag e 46 Please call NTAC (National Technical Assistance Center) for this data assignment. Action by Maintenance Person : :