NEC Neax 2000 Ivs2 Wcs System Manual

							CHAPTER 3 SYSTEM DATA PROGRAMMING
PS Data Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 53
PS DATA PROGRAMMING
Perform the following procedure after completing SYS ID Assignment and ZT Authorization.
DESCRIPTION DATA
Assign a PS station No. to the required
vir tual PS LEN.
NOTE 1:When the Expansion Memory
card (PZ-M537) is not mounted
on the MP card, the 1st data is
000-127.
NOTE 2:For Roaming PS, max. 5 digits
PS station number should be
assigned.(1)
(2)000-255 : Virtual PS LEN
X-XXXXXXXX : PS station No.
(X=0-9, *, #)
AssignaPS-ID.
(Primary PS station only)
NOTE 1:Insert leading zeroes in the PS-
ID for a maximum of nine digits.
For example, if PS ID is 1234,
enter 000001234 as the PS-ID.
NOTE 2:When a PS is assigned as a sub-
line (second line), CM1D YY=21
should not be assigned and must
be set to default “NONE”.
See
Multi-Line Operation-PS on Page
75
.
(1)
(2)YY=21
X-XXXXXXXX : PS station No.
XX···XX : PS-ID (Max. 9 digits,
Decimal)
NOTE 3:PS-ID is shown inside the
battery compa rtment of your
PS.
Fo r the D
termPS II, specify the terminal
kind of the PS as “DtermPS II”.
SetthisdataalsototheSub-linePS
station number, if provided.
(1)
(2)YY=15
X-XXXXXXXX: PS station No./Sub-line
PS station No.
00 : D
termPS II
15 : Former Dter mPS
Assignthesub-linePSnumbertoeach
primary PS station.
(1)
(2)YY=01
X-XXXXXXXX: Primary PS station No.
X-XXXXXXXX: Sub-line PS station No.
CM1D START
CM1C
A

 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 54ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
PS Data Programming
DESCRIPTION DATA
Assign the Service Restriction Class to
each PS station.
(1)
(2)YY=02
X-XXXXXXXX : PS station No.
XX ZZ
XX : Service Restriction
Class A (00-15 )
When providing Roaming service, specify
the Service Restriction Class for Roaming
service data download.
NOTE 1:Assign the same Service
Restriction Class data to the PS
station number and the Vi rtual
LC station number
(For Roaming service, see
Visitor PS Data Programming
on Page 93).
NOTE 2:When the roaming service is
provided, in the system where
the second line service is also
provided, it is recommended to
set the primary PS-stations in
different service restriction class
than sub-lines, since sub-lines
do not support the roaming
feature.
(1)
(2)YYY=117
00-15: Service Restriction Class A
assigned by CM12 Y=02
0:Allowed
1 : Restricted
When providing Roaming service, assign
theHomePBXIDofownPBXtowhichthe
PS belongs. Assign the same number with
the first 4 digits of the Individual PS num-
ber.
(1)
(2)YY=00
04 (Assignment of Home PBX ID)
X-XXXX: Home PBX ID
(1-4 digits, Decimal)
CM12
A
B
CM15
CMAE

 
 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
PS Data Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 55
 When changing the PS operation data
If you change the PS operation data in this section which hasbeen already downloaded to a PS,
do PS data download (CM1D YY=20 second data: 1) again.
DESCRIPTION DATA
Download the PS operation data to each
PS by assigning the 2nd data 1.
(1)
(2)YY=20
X-XXXXXXXX : PS station No.
1 : To be executed
Refer to “D
termPS User Manual”.
NOTE 1:All steps for setting up ZTs and
all wiring must be successfully
completed and ZTs must be idle
before downloading PS
operation data.
NOTE 2:When a PS is set up initially, set
thePSinDataDownloadMode
by applying power to the PS
while pressing the SEND key,
and then execute the CM1D
Y=20 in Calling Area No. 00.
NOTE 3:Set the D
termPS II to download
mode by simultaneously
applying power to the D
termPS II
and pressing the L1 key.NOTE 4:If the download is successful,
it will display the D
termPS II
number for 2 seconds,
automatically reset, then
return to stand-by mode.
If the download failed, an
error tone will sound and the
D
termPS II displays
“Download Failed”.
Download must be
performed again. If this
procedure continues to fail,
contact the Service Center.
NOTE 5:The following messages
display on the MAT.
STATUS
DISPLAY
Loading succeeded OK
PS is busy WAIT BUSY NOW
PSisoutofarea WDERROR
Lack of PS data DATA ERROR
END
CM1D
B 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 56ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Virtual Line/Trunk Data Programming (For Integrated/Adjunct CCIS)
VIRTUAL LINE/TRUNK DATA PROGRAMMING
(FOR INTEGRATED/ADJUNCT CCIS)
This programming is required for Integrated Type or Adjunct Type (CCIS Interface).
DESCRIPTION DATA
Assign a vir tual station number to the
required LEN.
NOTE 1:The Vir tual LEN must be as-
signed from the last LEN 763.
NOTE 2:Do not assign the same station
No. to the Vir tual Station No. and
the PS Station No.(1)
(2)763-000 : LEN
NOTE 1
X-XXXXXXXX : Virtual Station No.
NOTE 2
Specify a path between the virtual line and
virtual trunk.
(1)
(2)YY=00
256-511 : Virtual Trunk No.
NOTE 3,NOTE 4
X-XXXXXXXX : Virtual Station No.
NOTE 3:PS station No. is assigned by the first data of CM1C (Virtual PS LEN) as follows.
Virtual Trunk No. minus 256 equals Vir tual PS LEN.
For example, when the Virtual Trunk No. is 256 (CM5A YY=00 1st data: 256), then
the Vir tual PS LEN is 000 (CM1C 1st data: 000).
NOTE 4:When the Expansion Memory card (PZ-M537) is not mounted on the MP card, the
first data is 256-383.
CM5A START
CM10
A 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Virtual Line/Trunk Data Programming (For Integrated/Adjunct CCIS)
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 57
DESCRIPTION DATA
The following data is set automatically by the virtual line-trunk path setting of CM5A YY=00.
If you clear CM5A YY=00 setting data, the following data is also cleared automatically.
NOTE:The trunk route data must be assigned by CM35because the trunk route data is
not automatically assigned.
The trunk route of the Virtual Trunk is 63 by the default data setting. If you want
other use for the trunk route 63, change the trunk route number of Virtual Trunk
routebyCM30YY=00.
CM5A
A
B
COMMAND
CODE MEANINGS 1ST DATA 2ND DATA MEANING
CM12 YY=00 DTMF/DP Virtual Station No.
assigned by CM101DP
CM13 YY=18 Reverse signal
sending to stationVirtual Station No.
assigned by CM100 Send
CM30 YY=00 Trunk route alloca-
tionVirtual Trunk No.
256-51163NOTETrunk Route No. 63
CM30 YY=02 Terminating system
in Day ModeVirtual Trunk No.
256-51104 Direct-In Termination
CM30 YY=03 Terminating system
in Night ModeVirtual Trunk No.
256-51104 Direct-In Termination
CM30 YY=04 Destination of DIT
in Day ModeVirtual Trunk No.
256-511PS Station No. Station No. of DIT
destination
CM30 YY=05 Destination of DIT
in Night ModeVirtual Trunk No.
256-511PS Station No. Station No. of DIT
destination
CM30 YY=40 Terminating system
in Mode AVirtual Trunk No.
256-51104 Direct-In Termination
CM30 YY=41 Terminating system
in Mode BVirtual Trunk No.
256-51104 Direct-In Termination
CM30 YY=42 Direct-In Termina-
tion in Mode AVirtual Trunk No.
256-511PS Station No. Station No. of DIT
destination
CM30 YY=43 Direct-In Termina-
tion in Mode BVirtual Trunk No.
256-511PS Station No. Station No. of DIT
destination
CM12 YY=16 Trunk to be seized PS Station No.
Virtual Trunk
No. D256-D511Tr u n k N o . 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 58ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Virtual Line/Trunk Data Programming (For Integrated/Adjunct CCIS)
DESCRIPTION DATA
Change the trunk route for the vir tual trunk
number, if required.
(1)
(2)YY=00
256-511: Virtual Trunk No.
00-63 : Trunk No.
Assign the data for the Virtual Line/Trunk
to the trunk route No. assigned by CM30
YY=00.
(1)
(2)YY=00 (Kind of Route)
00-63 : Trunk Route No.
00 : DDD

(1)
(2)YY=01 (Type of Signal)
00-63 : Trunk Route No.
4:DTMF

(1)
(2)YY=04 (Answer Signal Condition)
00-63 : Trunk Route No.
1 : Answer Signal by Polarity
Reversal

(1)
(2)YY=05 (Release Signal Condition)
00-63 : Trunk Route No.
1 : Release Signal from C.O.

(1)
(2)YY=09 (Incoming Connection Signaling)
00-63 : Trunk Route No.
15 : Ring Down (Loop Start)

(1)
(2)YY=20 (Sender Start Condition)
00-63 : Trunk Route No.
15 : Timing Start

(1)
(2)YY=98 (Designated Seizure of trunks)
00-63 : Trunk Route No.
0 : Allowed
Specify the COT card Terminating
Impedance.
(1)
(2)YYY=100
00-63 : Trunk Route No.
0 : 600 ohm/complex BNW for Inte-
grated Type and Adjunct Type
(CCIS Interface)
2 : 600 ohm/600 ohm for Adjunct
Type (Analog Interface)
CM30
B
END
CM35 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk Data Programming (For Adjunct Analog)
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 59
TRUNK DATA PROGRAMMING (FOR ADJUNCT ANALOG)
This programming is required for Adjunct Type (Analog Interface).
DESCRIPTION DATA
Assign a trunk number to the required
LEN.(1)
(2)000-763 : LEN
0-7 (PIM0-7) +
00-63 (Port No.)
D000-D255 : Trunk No.
Assign the trunk route number to the trunk
number.
(1)
(2)YY=00 (DP or DTMF)
000-255: Trunk No.
00-63 : Trunk Route No.
Assign the data for terminating system.



(1)
(2)YY=02 (Day Mode)
YY=03 (Night Mode)
YY=40 (Mode A)
YY=41 (Mode B)
000-255: Trunk No.
04 : Direct in Termination
Assign the PS station number to be termi-
nated by Direct-In Termination.



(1)
(2)YY=04 (Day Mode)
YY=05 (Night Mode)
YY=42 (Mode A)
YY=43 (Mode B)
000-255 : Trunk No.
X-XXXXXXXX : PS Station No.
Assign the kind of trunk to the trunk route.
(1)
(2)YY=00
00-63 : Trunk Route No.
00 :C.O.Trunk
Specify the dialing signal type to the trunk
route.
(1)
(2)YY=01
00-63 : Trunk Route No.
2 : Call Origination-DP
Call Termination-DP
4 : Call Origination-DTMF
Call Termination-DTMF
7 : Call Origination-DP/DTMF
Call Termination-DTMF
Assign the call direction to the trunk route.
(1)
(2)YY=02
00-63 : Trunk Route No.
3:BothwayTrunk
CM35 START
CM10
CM30
A 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 60ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk Data Programming (For Adjunct Analog)
DESCRIPTION DATA
Specify the answer signal from the distant
office for outgoing connection to the trunk
route.
(1)
(2)YY=04
00-63 : Trunk Route No.
1 : Battery Reversal
7 : Answer signal does not arrive
from C.O. Line (Answer timing
shall be set by CM41 Y=0
Function No. 03)
Specify the release signal from the distant
office for an outgoing connection of an
incoming connection to the trunk route.
NOTE:If Adjunct Type (Analog Inter-
face), using a line card over the
Main PBX is recommended to
provide the release signal (i.e.,
momentarily, an open circuit).
(1)
(2)YY=05
00-63 : Trunk Route No.
0 : Release signal does not arrive
1 : Release signal arrives
Assign the sending of the dial pulse on an
outgoing call to the trunk route.
(1)
(2)YY=08
00-63 : Trunk Route No.
3 : Dial pulses are sent out
Assign the incoming connection signaling
to the trunk route.
(1)
(2)YY=09
00-63 : Trunk Route No.
15 : Ring Down (Loop Start C.O.)
Assign the sending of Hook Flash to
outside to the trunk route.
(1)
(2)YY=16
00-63 : Trunk Route No.
1:Sending
Assign the Sender start condition to the
trunk route.
(1)
(2)YY=20
00-63 : Trunk Route No.
15 : Timing Start
CM35
A
B 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk Data Programming (For Adjunct Analog)
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 61
DESCRIPTION DATA
Specify the Sender prepause timing to the
trunk route.
NOTE:To reduce the connecting time, it
is preferable to shor ten the
prepause timing (i.e., second
data=03 (1.5 sec.))
(1)
(2)YY=21
00-63: Trunk Route No.
00: 0 sec. 08 : 6.0 sec.
01: 0.5 sec. 09 : 7.0 sec.
02: 1.0 sec. 10 : 8.0 sec.
03: 1.5 sec. 11 : 9.0 sec.
04: 2.0 sec. 12 : 10.0 sec.
05: 2.5 sec. 13 : 11.0 sec.
06: 4.0 sec. 14 : 12.0 sec.
07: 5.0 sec. 15 : 3.0 sec.
Specify the DP Inter-Digital Pause to the
trunk route.
(1)
(2)YY=23
00-63: Trunk Route No.
0: 200 ms. 4 : 600 ms.
1: 300 ms. 5 : 800 ms.
2: 400 ms. 6 : 1000 ms.
3: 500 ms. 7 : 700 ms.
Specify the DTMF Inter-Digital Pause to
the trunk route.
NOTE:To reduce the connecting time, it
is recommended to shorten the
DTMF inter-digital Pause timing
(YY=24), i.e., second data= 2
(80 ms). YY=26, i.e., second
data=0 (64 ms).
(1)
(2)YY=24
00-63 : Trunk Route No.
0: 40 ms. 4 : 160 ms.
1: 60 ms. 5 : 200 ms.
2: 80 ms. 6 : 240 ms.
3: 100 ms. 7 : 120 ms.
CM35
B
C 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 62ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk Data Programming (For Adjunct Analog)
DESCRIPTION DATA
Specify the DP Make Ratio.
(1)
(2)YY=25
00-63 : Trunk Route No.
0 : 39 % Make Ratio
1 : 33 % Make Ratio
Assign the DTMF signal width to the trunk
route.
NOTE:To reduce the connecting time, it
is recommended to shorten the
DTMF inter-digital Pause timing
(YY=24), i.e., second data=2 (80
ms). YY=26, i.e., second data=0
(64 ms).
(1)
(2)YY=26
00-63 : Trunk Route No.
0:64ms.
1:128ms.
Assign the trunk release by detection of re-
versal of tip and ring to the trunk route.
(1)
(2)YY=39
00-63 : Trunk Route No.
0 : Not to be released
1 : To be released
CAUTION:Check the timing on main PBX before making any change on timing function.
Specify the DP Sender release timing to
the trunk route.
(1)
(2)YY=45
00-63 : Trunk Route No.
0:2sec.
1:4sec.
2:6sec.
3:8sec.
4 : 12 sec.
5 : 14 sec.
6 : 16 sec.
7 : 10 sec.
CM35
C
D