NEC Neax 2000 Ivs2 Wcs System Manual

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 83
DESCRIPTION DATA
Specify the order of LCR selection for the
Route Pattern No. assigned by
YYYY=4000-4007.
(1)
(2)YYYY=0000-0255
(Route Pattern No. 000-255)
1-4: Order of LCR Selection
1: 1st
2: 2nd
3: 3rd
4: 4th
XXX ZZ
XXX: 000-255
(LCR Pattern No. 000-255)
ZZ: 00-63 (Trunk Route No. 00-63)
To delete the designated digit of an area
code:
(1)
(2)YYYY=5000-5255
153 (Designation of digit to be deleted)
00: No digits deleted
01: First digit deleted
10: First 10 digits deleted
CCC: No digits deleted
Assign the digits to be added to the digits
sent to the distant office.
For Closed Numbering System, this
assignment is not required.
(1)
(2)

(1)
(2)YYYY=5000-5255
100 (Designation of digit Addition Pat-
tern No.)
9000-9255 (Digit Addition Pattern No.
000-255)
CCC: No digits added
YYYY=9000-9255
(Digit Addition Pattern No. 000-255)
0
X-X...X [Digits to be added (Max. 32
digits)]
X=0-9, A (*), B (#), C (Fixed Pause)
D (Programmable Pause)
CM8A
A
B|| 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 84ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Specify the maximum number of digits to
be dialed by the calling pa rty.
The maximum number of digits including
the area codes should be assigned to
each area code.
(1)
(2)Y=0-7 (Area Code Development
Pattern No. 0-7 assigned by CM8A,
Y=A00)
X-X...X (Area Code dialed, Max. 8
digits)
01 : 1 digit
24 : 24 digits
79 : 79 digits
END
B
CM85
||
|| 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 85
Q931a Digital Trunk Data Programming
 DTI Assignment
DESCRIPTION DATA
Assign an AP number to the DTI card.
The AP number must match the SENS
switch setting on the DTI card.
(1)
(2)Y=0
04-15, 20-31: AP No.
09: DTI card
Assign the trunk number to each channel
number on the DTI card.
NOTE:The system allocates time slots
to consecutive channels from
lowest to highest channel
number assigned. To minimize
the number of time slots
allocated, assign trunk numbers
to the consecutive channels on
each card. Never skip channels
in CM07.
(1)
(2)YY=01
XX ZZ
XX : AP No. (04-15, 20-31) assigned
by CM05
ZZ : Channel No. of DTI
Fo r 2 4DTI
00-22 : B channel
23 : D channel
Fo r 3 0DTI
01-15, 17-31 : B channel
16 : D channel
D000-D255: Trunk No.
Analog Trunk number already assigned
by CM10 cannot be used.
CM07 START
CM05
A
INITIAL
INITIAL 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 86ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Assign a Trunk Route to each trunk
number used for voice channel (B
channel), and also to signaling channel (D
channel). Make a separate route for B
channels and D channels.
NOTE:DTI route must be separated
from analog trunk
routes

(1)
(2)YY=00
000-255: B Channel, D channel Trunk
No. assigned by CM07 YY=01
00-63: Trunk Route No.
Assign the terminating system to each
incoming trunk used for voice channel, as
“dial-in”.



(1)
(2)YY=02 (Day Mode)
YY=03 (Night Mode)
YY=40 (Mode A)
YY=41 (Mode B)
000-255: B Channel Trunk No.
assigned by CM07 YY=01
21: Dial-in
Assign the CIC (Circuit Identification
Code) to each voice channel trunk.
(1)
(2)YY=07
000-255: B Channel Trunk No.
assigned by CM07 YY=01
000-022: CIC 000-CIC 022CM30
A
B 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 87
DESCRIPTION DATA
Assign trunk route data to each channel
trunk route number assigned by CM30
YY=00.
(1)
(2)YY=00 (Kind ofTrunk Route)
00-63: B Channel, D Channel Route No.
04: Tie Line

(1)
(2)YY=01 (Dialing Signal Type)
00-63: B Channel Route No.
7 : Call Termination; DP/DTMF
Call Origination; DTMF

(1)
(2)YY=04
(Answer Signal from Distant Office)
00-63: B Channel Route No.
2 : Answer signal arrives.
7 : Answer signal does not arrive.

(1)
(2)YY=05
(Release Signal from Distant Office)
00-63: B Channel Route No.
0 : Release signal does not arrive.
1 : Release signal arrives.

(1)
(2)YY=09 (Incoming Connection Signaling)
00-63: B Channel Route No.
08: Q931a
CM35
B
C 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 88ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
T/R: Transmitter PAD/Receiver PAD
+: Gain
–: Loss
(1)
(2)YY=19
00-63: B Channel Route No.
0:
1 : Programmable PAD
2: (SeeCM42)
3:
4:
5: FixedPAD
6 : (See left table)
7:
When using the programmablePAD
(CM35 YY=19, 2nd Data=0-3), assign the
PAD data.(1)
(2)50-65
00-15
T/R: Transmitter PAD/Receiver PAD
+: Gain
–: Loss
CM35
C
CM42
D
CONNECTION
PATTERNSPADDATAOFDTI[dB]
DATA
=4
(T/R)DATA
=5
(T/R)DATA
=6
(T/R)DATA
=7
(T/R)
Station-DTI –3/–8 –3/–3 –3/–3 –3/–8
Tone-DTI 0/0 0/0 0/0 0/0
COT/LDT-DTI 0/0 0/0 0/0 0/0
ODT -DTI +3/–3 0/0 0/0 +3/–3
DTI-DTI 0/–6 0/0 0/–6 0/0
See the following tables.
PADDATAPATTERNS
CONNECTING
PATTERNS CM35 YY=19
2ND DATA=0CM35 YY=19
2ND DATA=1CM35 YY=19
2ND DATA=2CM35 YY=19
2ND DATA=3
50
6550 54 58 62 STA/TONE-DTI
51 55 59 63 COT/LDT-DTI
52 56 60 64 ODT-DTI
53 57 61 65 DTI-DTIPATTERN
1ST DATA
~
PAD DATA OF DTI (T/R) [dB] REMARKS
00
1500 0/0
01 –2/–2
02 –3/–3
03 0/–6
04 –3/–8
05 +3/–3
06 –6/–6
07 –8/–8
08
15Not Used
PATTERN
2ND DATA
~
~ 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 89
 DCH Assignment
DESCRIPTION DATA
Assign an AP number to the DCH card
(PN-SC01).
The AP number must match the SENS
switch setting on the DCH card.
(1)
(2)Y=0
04-15, 20-31: AP No.
35: DCH for Roaming
Assign the DCH number to the AP number
of DCH assigned by CM05.
(1)
(2)YY=08
0-7: DCH No.
04-15, 20-31: AP No. assigned by
CM05
Execute CM35 YY=90 for the B channel
route and D channel route.
(1)
(2)YY=90 (Special Facilities)
00-63: B Channel, D Channel Route
No.
6: PBX-PBX Interface for Roaming
(Q931a digital)
Assign the DCH number to the voice
channel trunk route assigned by CM30
YY=00.
(1)
(2)YY=93
(Assignment of D ChannelHandler)
00-63: B Channel Route No.
00-07: DCH No. (0-7)
15 : Not used
CM05
D
E
CM06
CM35
INITIAL
INITIAL 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 90ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Specify the LAPD Mode of the D channel
route as “Network Mode” or “User Mode”.
This data must be set differently between
the opposite DTIs. When the opposite
office is a master office, set this data to 1
(User Mode), and when the opposite office
isaslaveoffice,setthisdatato0(Network
Mode).
(1)
(2)YYY=113 (LAPD Mode)
00-63: D Channel Route No.
0:NetworkMode
1 : User Mode
Assign the roaming service to each B
channel and D channel route.
(1)
(2)YYY=140 (Roaming Service)
00-63: B Channel, D Channel Route
No.
0: Available
Provide pursuit function after the roaming
PS to each B channel route.
(1)
(2)YYY=141 (Roaming PS Pursuit)
00-63: B Channel Route No.
0: Provided
Specify the protocol type between the
PBXs as “Q931a-Digital”.
(1)
(2)YYY=142 (Protocol between PBXs)
00-63: B Channel, D Channel Route
No.
1: Q931a-Digital
Assign the trunk number assigned by
CM07 YY=01 to each DCH number for
providing D channel path between DTI and
DCH.
NOTE:Confirm that the SC01 Run LED
is flashing.
(1)
(2)YY=00
0-7: DCH No.
000-255: Trunk No.
When the Network Numbering Plan is the
Open Numbering System, assign the
Home PBX ID for the indication on the PS/
D
term.
(1)
(2)YY=01
0-7: DCH No.
X-XXXX: Home PBX ID
(1-4 digits, Decimal)
END
E
CM35
CMA9
DBM INITIAL
DBM INITIAL
INITIAL 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 91
Home PS Data Programming
DESCRIPTION DATA
Assign an AP number to the DBM (Data
Base Module) card (PN-AP00-A).
The AP number must match the SENSE
switch setting of the card.
(1)
(2)Y=0
04-15: AP No.
34: DBM (AP00-A) for Roaming
Assign the Trunk Restriction Class for
Home PS. This data is sent to the visitor
PBX when the PS is roaming.
NOTE 1:When the location registration of
a Visitor PS is executed, the
Trunk Restriction Class assigned
on the Home PBX is notified to
the Visitor PBX being substituted
as follows.
(1)
(2)YY=01 (Trunk Restriction Class)
X-XXXXXXXX: Virtual LC station No.
XY
X: Trunk Restriction Class in Day Mode
(1 -8)
Y: Trunk Restriction Class in Night
Mode (1 -8)
1 : Unrestricted (RCA)
2 : Non-Restricted 1 (RCB)
3 : Non-Restricted 2 (RCC)
4 : Semi-Restricted 1 (RCD)
5 : Semi-Restricted 2 (RCE)
6 : Restricted 1 (RCF)
7 : Restricted 2 (RCG)
8 : Fully-Restricted (RCH)
Assign the Service Restriction Class for
Home PS.
NOTE 2:Different Service Restriction
Class for Multi-Site Roaming
must be assigned to the PSs
according as whether the PS is
used for Roaming.
(1)
(2)YY=02 (Service Restriction Class)
X-XXXXXXXX: Virtual LC station No.
XX YY
XX: Service Restriction Class A
(00-15 )
YY: Service Restriction Class B
(00-15 )START
CM05
CM12
A
INITIAL
CM12 YY=01 Settings
on the Home PBX Notified Class
1: Unrestricted (RCA) 1
2: Non-Restricted 1 (RCB) 2
3: Non-Restricted 2 (RCC) 3
4: Semi-Restricted 1 (RCD) 4
5: Semi-Restricted 2 (RCE) 4
6: Restricted 1 (RCF) 5
7: Restricted 2 (RCG) 5
8: Fully-Restricted (RCH) 6 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 92ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Assign the Tenant number to the Home
PS. This data is sent to the visitor PBX
when the PS is roaming.
NOTE 3:It is recommended to assign the
PS station (CM1C) and its
related virtual LC station number
to the same service restriction
class when roaming is provided.
SeePS Data Programming on
Page 53
(1)
(2)YY=04 (Service Restriction Class)
X-XXXXXXXX: Virtual LC station No.
00-63: Tenant No.
01
Specify the Service Restriction Class for
Roaming service download.
NOTE:Assign the same Service
Restriction Class data to the
Virtual LC station number and
the PS station number for
Roaming service.
(1)
(2)YYY=117
00-15: Service Restriction Class A
Assigned by CM12 YY=02
0:Allowed
1 : Restricted
Specify whether the Home PBX
Numbering Plan is the Open Numbering
System or Closed Numbering System.
This assignment defines whether the
Home PBX ID is added to the Roaming
number, and to the Originating number
sent to the Visitor PBX.(1)
(2)088 (Home PBX Numbering Plan)
0 : Closed Numbering System
1 : Open Numbering SystemA
CM12
END
CM15
CM08