Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Customer Data Entry (CDE)intercept or Do Not Disturb intercept).
Nl: This field specifies where calls route during Night1 Service Mode
by the extension number. If this field is blank, then the call reroutes to
the number specified in the DAY field.
N2: This field specifies where calls route during Night2 Service Modeby the extension number. If this field is blank, then the call does not
reroute.CALL REROUTING OPTIONS
Ca I I Type
Station Dial 0 Routing
Priority Dial 0 Routing
DID Recall Points on Busy
DID...

SECTION MITL9109-094~Zl O-NA25). The system displays the selected Tenant Group number on the
header line.
8-DELETE: This 
softkey appears when the pointer is pointing to data
(i.e., data on the command line). Pressing the DELETE 
softkey removes
the selected rerouting designation from the form. The deletion is com-
pleted by pressing the ENTER 
softkey.O-ENTER: This 
softkey appears only after data for an entry number
has been modified. Pressing the ENTER 
softkey commits each modi-
fication one at a...

Customer Data Entry (CDE)
Form 20 - ARS: COR Group Definition
4.87Class of Restriction groups together users with the same out-
side call capabilities. A COR is assigned to each Attendant
Console, station, 
SUPERSET telephone and Dial-In Trunk. This form
specifies the Class-of-Restriction (COR) Group memoers. Refer to Ta-
ble 4-34, ARS: COR Group Definition for the form layout. The system
supports a maximum of 50 COR Groups with up to 25 
CORs per group.
Each COR Group specifies by COR number those...

SECTION MITL9109-094-Zl O-NA4.89 Commands
4-TOP: Pressing the TOP 
softkey moves the line pointer to the first
line of the form. The command line displays the first line.
S-BOTTOM: Pressing the BOTTOM 
softkey moves the line pointer to
the last 
line of the form. The command line displays this line.
6-QUIT: Pressing the QUIT 
softkey when editing this form returns the
display to the level before the field was modified. The change is not
saved. At all other times, pressing this 
softkey exits Form 20 and...

Customer Data Entry (CDE)
Form 21- ARS: Day Zone Definition
4.90 This form defines the day zones for each day of the week.
There are a maximum of three day zones. Note that all days of
the week must have a zone specification before this form can be
saved. Refer to Table 4-35, 
ARS. Day Zone Definition for the form
layout.TABLE 4-35
FORM 21
- ARS: DAY ZONE DEFINITION
CDE TERMINAL DISPLAY
7:50 AM 15JAN-88alarm status = NO ALARM
DAY ZONEMON.TUE.WED.
THJ.FRI.SAT.SW.
01*****
8:
**
01
1 -ENABLE6-QUITtt***2-...

SECTION MITL9109-094-210-NA
softkey sets the selected day to the day zone that is displayed on the
command line. The form displays an asterisk 
(* ) in the selected day
field opposite the chosen day zone. When the cursor is at an asterisk,
this 
softkey displays DISABLE. Pressing the DISABLE softkey removes
that day specification from the selected day zone. The asterisk dis-
appears and the 
softkey displays ENABLE again.
6-QUIT: Pressi-ng the 
QUIT‘softkey when editing this form returns the
display to...

Customer Data Entry (CDE)
Form 22 - ARS: Modified Digit Table
4.93This form specifies those digits that modify the user-dialed
digits. The digit modification prepares the dialed digits for dial-ing out on certain trunks such as FX, TIE and WATS. Refer to Section
MITL9109-094.-220-NA, Automatic Ro,rte Selection and Toll Control for
details. Refer to Table 4-36, ARS: Modified Digit Table for the form
layout.TABLE 4-36
FORM 22 
- ARS: MODIFIED DIGIT TABLE
CDE TERMINAL DISPLAY
II:01 PM 15-JAN-88alarm status...

SECTION MITL9109-094-210-NA
-i
I= Pause for 5 Seconds
‘2 = Wait for Dial Tone
*3 = Switch to DTMF for Subsequent Digits
“4 = Do not Display Further Modified Digits on Sets or
SMDR
*x5 = Pause 10 Seconds.
The asterisk 
(*) character above is generated on the Attendant Console
and the terminal by pressing the
* key. If however, the asterisk char-
acter is required in a string of characters, the 
* key must be pressed
twice.
COMMENTS: This field is reserved for additional data (a maximum of
20 characters)....

Customer Data Entry (CDE)
Form 23 - ARS: Route Definition
4.96 This form defines each ARS Route by specifying the Trunk
Group number, COR Group number and the Modified Digit Entry.
Refer to Table 4-37, ARS: Route Definition for the form layout.TABLE 4-37
FORM23
-ARS: ROUTEDEFINITION
CDE TERMINAL DISPLAY
7:50 AhI 15-JAN-88alarm status = NO ALARM
ROUTE 
NLblTRU’JK GROUPCOR GROUPMOD DIGIT ENTRYlXNlMENTS
01
118:2 12 1:LOCAL WD3Bm LONG DISTANCE 2 WATS DC0
i:06
07
08
09
10
1112
01
I-QUIT
111LOCAL Dw2-3-4-TOP...

SECTION MITL9109-094-210-NACOMMENTS: This field is reserved for additional data (a maximum of
20 characters). It is stored by the system but not used.
4.9%Commands
4-TOP: Pressing the TOP 
softkey moves the line pointer to the first
line of the form. The command line displays the first line.
5-BOTTOM: Pressing the BOTTOM 
softkey moves the line pointer to
the last line of the form. The command line displays this line.
6-QUIT: Pressing the QUIT 
softkey when editing this form returns the
display to the...