Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Customer Data Entry (CDE)
Session Inactivity Disconnect Timer
The DATASET monitors the time from the last transmitted or received
character. If the programmed time period is exceeded, the data call isdropped. This timer has a range of 0 to 255 minutes. It is disabled if
set to 0 minutes.Guard Timer
After a 
DATASET has disconnected, the Guard Timer keeps the
DATASET unavailable for a short time period to allow the far end to
clear down. This timer has a range of 0 to 99 seconds in 1 second...

SECTION MITLSI 09-094-210-NAto the 
dataset after the attached device has asserted DTR. The timer
has a range of 0 to 
9900 milliseconds, in 100 millisecond increments.
DTR Forced HighWith this option enabled, the system assumes DTR of the attached
device is high, regardless of its actual state. If a modem adapter is
inserted in the RS-232 connection, this option applies to DSR instead.
RTS Forced HighWith this option enabled, the system assumes RTS of the attached
device is high, regardless of its...

Customer Data Entry (CDE)0DSR: The system alerts the DTE by raising DSR. If DTR is high
when the DTE is called, the call is barred.
aDCD: The system alerts the DTE by raising DCD. If DTR is high
when the DIE is called, the call is barred.
lREFUSE: The DTE is only seized when DTR is h@h. If DTR is
low when the DTE is called, the call is barrad.Pooled Modem Communication Established Indicator
When the system is establishing data communication between a
Pooled Modem and a remote modem, this parameter...

SECTION MITL9109-094-210-NA -
ASYNC: XOFF CharacterThis character stops transmission between the 
dataset and the at-
tached device. It is programmed as the decimal equivalent of the
desired ASCII character. The most widely used XOFF character is
Control-S, whose decimal equivalent is 19.
ASYNC: Break Key FunctionThis parameter specifies the function of the BREAK key. The options
are:
aSYS ATT: the current DTRX data call is dropped and the user is
prompted to dial another data call. If the current data...

Customer Data Entry (CDE)
Character 2 is non-zero, both characters are sent.
This feature is designed for attached devices which can automatically
set their baud rate and/or parity from specific characters. If the at-
tached device does not have this capability, one of the following
should be done:aSet Minimum Baud Rate =Maximum Baud Rate = Default Baud
Rate
or,
lEnable the “Always Use Default Baud Rate When Called” param-
eter
With one of the above options selected, the 
Autobaud To Host char-
acters...

SECTION MITL9109-094-210-NAsignals come from the 
DATASET’s receiver Phase Locked Loop
(PLL). The PLL extracts the timing from the data received from
the far end data set.
TX EXT: This option applies to both DCE and DTE operation. The
DTE Receive clock signal comes from the 
DATASET’s receiver
Phase Locked Loop (PLL). The PLL extracts the timing from the
data received from the far end 
DATASET. When the DATASET2100 is operated as a DCE, the DTE Transmit clock signal
comes from an external clock signal on...

Customer Data Entry (CDE)
Review List for Form 114.54This form appears when the REVIEW softkey is pressed in Form11 
-Data Circuit Descriptor. This form lists all the users of a
particulardescriptor,identified bytheirphysicallocation(BAY/SLOT/CIRCUIT). Refer to Table 4-21, Review List for Form 11.
Note the data in this form cannot be modified.TABLE 4-21
REVIEW LIST FOR FORM 11
CDE TERMINAL DISPLAY
8:40 AM 15-JAN-88
[ DESCRI PTOR NWlBER : 1 ]1BAY
SLTcc-rSCTCOMMENTS
4
2
I
424-5-
6-QUIT7-DESC NlJlBER 8-...

SECTION MITL9109-094-210-NA
II-DE% NUMBER: Pressing this softkey causes the system to request
which Descriptor number to display. Complete the entry by pressing
ENTER.Page 66 

Customer Data Entry (CDE)
Form 12 -Data Assignment
4.57When a Digital Line card is programmed in the System Configu-
ration Form, the system creates an entry line for each of its
circuits in Form 09, 
StationsISUPERSET Telephones and in Form 12,
Data Assignment. (Refer to Table 4-22, Data Assignment). If the card is
in an upper (high power) slot, the system also creates entry lines for
its circuits in Form 07, Console Assignments.
When the programmer assigns a Digital Line Card port as a 
DATASET,the...

SECTION MITL9109-094-210-NA4.58Field Description
BAY/SLT/CCT/:This field specifies the physical location of each
device. This list is generated by the system based on what was en-
tered in the programmed field of Form 01, System Configuration. Note
this field cannot be modified.
TYP: This field identifies the type of data device programmed. The
available devices are: 
DATASET 1101, DATASET 1102, DATASET 1103,
DATASET 2102, DATASET 2103 and DSCONS.
TEN: The tenant group for each device is specified in...