Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Customer Data Entry (CDE)
Pressing the ENABLE softkey enables the selected option. The STATUS
field shows the ENABLED prompt. Note: The enable (or disable) process
is completed by pressing the ENTER 
softkey.l-VARIABLE: This 
softkey appears only when System Option 55 is
selected (displayed on the command line). Pressing the VARIABLE 
soft-key sets the status of System Option 55 to Variable; the STATUS field
shows the VARIABLE prompt. The selection is 
compieted by pressing
the ENTER 
softkey. Now,...

SECTION MITL9109-094-210-NAOPTION NUM: prompt on the command line. The selection is com-
pleted by entering a valid option number (1 to 58). The command line
displays that System Option (or System Timer) name, status and num-
ber.8-SHOW DISABLE/SHOW ENABLE: This 
softkey has two functions; it
displays the disabled and enabled System Options. Pressing the SHOW
DISABLE 
softkey displays the currently disabled System Options; the
softkey now shows the SHOW ENABLE prompt. Pressing the SHOW
ENABLE 
softkey...

Customer Data Entry (CDE)
TABLE 4-9
SYSTEM OPTIONS AND TIMERS
Option NumberSystem Options/System Timers0124 Hour Clock02RESERVED
03Single Paging Amplifier
04Message Waiting and Message Regieter Clear Print05Verified Account Codes06RESERVED
x;:RESERVED
RESERVED
09Attendant Call Block
10Attendant Conference Beeps
::Automatic Wake-up
Automatic Wake-up Alarm13Automatic Wake-up Print14Automatic Wake-up Music
:iData Demultiplexer
DID To Non-Co Trunk Via Attendant Inhibit
:;Discriminating Ringing
Discriminating...

SECTION MITL9109-094-210-NAForm 05 
- Tenant Interconnection Table
4.23 This form specifies which Tenant Groups may be connected
together. Refer to Table 4-10, Tenant Interconnection Table. The
system allows for a maximum of 25 Tenant Groups. Each group speci-fies its own trunk answering points, attendant answering points and
night service status.TABLE 4-10
FORM05
-TENANT INTERCONNECTION TABLE
CDE TERMINAL DISPLAY
IO:15 PM 15-JAN-88alarm status = NO ALARM
0102030405 06 07080910 11 12 13 14 15 16 17 18 19...

Customer Data Entry (CDE)
BUT NOT YET SAVED --“ENTER” TO SAVE. Pressing this softkey again
exits Form 05 and returns the display to the level where the forms are
selected. The change is not saved. Refer to Table 4-2, Available Forms.
6-CANCEL: Pressing the CANCEL 
softkey cancels the tenant number
entry. This 
softkey appears after a programming error. It is accom-
panied with an error message on the command line. Refer to Table
5-1, Programming Error Messages for a list of these error messages....

SECTION MITL9109-094-210-NAForm 06 
- Tenant Night Switching Control
4.26In some systems it is necessary for one attendant to control
the Night Service switching of more than one Tenant Group.
This form specifies which Tenant Groups are switched to Night Servicesimultaneously. Note that the system defaults to Tenant Groups
switching to Night Service independently of each other. Refer to Table
4-l 1, Tenant Night Switching Control.TABLE 4-11
FORM 06 
- TENANT NIGHT SWITCHINGCONTROL
CDE TERMINAL DISPLAY...

Customer Data Entry (CDE)64UIT: Pressing the QUIT softkey when editing this form displays the
following warning on the command line: DATA HAS BEEN CHANGED
BUT NOT YET SAVED --
“ENTER” TO SAVE. Pressing this softkey again
exits Form 06 and returns the display to the level where the forms are
selected. The change is not saved. Refer to Table 4-2, Available Forms.B-CANCEL: This 
softkey appears after a programming error has oc-
curred. Pressing the -CANCEL 
softkey returns the display to the level
where the...

SECTION MITL9l-O9-094-210-NAForm 07 
-Console Assignments
4.29This form specifies the physical location of each Attendant
Console. Refer to Table 4-12, Console Assignments for the form
layout. The system provides an entry line in Form 07 for each Console
Module and for each Digital Line circuit in a high power (upper) slot
not assigned to a 
SUPERSET Telephone or DATASET. The system can
support a maximum of 11 Attendant Consoles. There can be no more
than two Console Modules per Universal Card or four...

Customer Data Entry (CDE)
4.32Field Description
BAY, SLT and CCT: These fields specify the physical location of each
Attendant Console. They are generated by the system based on whatwas entered in the PROGRAMMED field in Form 01, System Configura-
tion. This field cannot be modified.EXT 
WJM: This field displays the extension number of each Attendant
Console. Calls directed to the console’s extension number route to
softkey 2 on the Attendant Console.COS: This field lists the Class-of-Service number...

SECTION MITL9109-094-210-NALDN Assignments first.
O-ENTER: This 
softkey appears only after data for an entry has been
modified. Pressing the ENTER 
softkey commits the data for each At-
tendant Console to the database. Attendant Consoles can only be
programmed one at a time. Therefore, the ENTER 
softkey must be
pressed after each Attendant Console is modified.
Page 38