Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Customer Data Entry (CDE)
TABLE 4-25 (CONT’D)
TRUNK HARDWARE OPTIONSTl LWGS TRUUK and Tl CO DI SA
No Seize Alarm
No Release Alarm
Toll Office
Is this a 
CCIDTMFDictation Trunk
Loop Start or Ground Start
Calling Party Disconnect Timer (1 
+ 12 minutes)
Guard Timer (0 -* 3000 ms) (100 ms inc)
Ring Cycle Timer (6 + IO s)Ringing Expected
Ringing 
Debounce Timer (5 + 12 seconds)
Seize Timer (IO -+ 60 s) (IO s increments)
Flash Timer (200 + 700 ms) (100 ms inc)
Interdigit Timer (300 - 800 ms) (100 ms inc)...

SECTION MITL9109-094-210-NAReview List for Form 13
4.66This form appears when the REVIEW softkey is pressed in Form
13 -Trunk Circuit Descriptors. The form lists the trunks that
use the selected trunk circuit descriptor. Refer to Table 4-26, ReviewList for Form 13 for the form layout. Note that the data in this form
cannot be modified.TABLE 4-26
12:00 
Ahl 15-JAN-88REVIEW LIST FOR FORM 13
CDE TERMINAL DISPLAY
alarm status = NO ALARM
[6CCTCDTRUdK :2 1TRK NWlBAYSLTCCT CoMulENTs
2
Iiiz2
35
:11
12ii:3
4...

Customer Data Entry (CDE)
4.68Commands
6-QUIT: Pressing the QUIT softkey returns the display to the point
where the REVIEW 
softkey was pressed.
6-CANCEL: This 
softkey appears after a programming error has oc-
curred Pressing the CANCEL 
softkey returns the display to the level
where the programming error occurred. The CANCEL 
softkey appears
with an error message.
7-DESC NUMBER:
This 
softkey selects a trunk circuit descriptor
number. Pressing the DESC NUMBER 
softkey displays the ENTER DESC.
NUM:...

SECTION MITL9109-094-210-NAForm 14 
-Non-Dial-In Trunks
4.69 This form specifies the characteristics of the system’s 
Non-Dial-In Trunks. These trunks cannot dial any digits into the
PABX and are usually a CO Trunk. The Day, 
Nl, N2 answer points are
assigned in this form. Alternate recall points are assigned in Form 19
(refer to Table 4-33, Call Rerouting Table). Refer to Table 
4-27, Non-Dial-In Trunks for the form layout.
TABLE 4-27
FORM 14 
- NON-DIAL-IN TRUNKS
4:26 PM15-JAN-88
BAY SLT CCT 
COS...

Customer Data Entry (CDE)
set or a SIJPERSET telephone, a Hunt Group Access Code , a Night Bell
extension number or an ACD Path access code. Note then that an LDN
and Night Bell cannot be rung simultaneously. Note that the DAY field
must be filled in before any changes for the selected physical locationare stored in the database. If the 
Nl or N2 field is not specified, then
the system defaults the night answer points to the day answer point. Ifonly one of the night answer points is specified, then the...

SECTION MITL9109-094-210-NA6-CANCEL: This 
softkey appears after a programming error has oc-
curred. Pressing the CANCEL 
softkey returns the display to the level
where the programming error was made. The CANCEL 
softkey appears
with an error message.
7-BAY/SLT/CCT: Pressing this softkey locates trunk via its bay, slot
and circuit numbers. The command line displays the Bay:, Slot: and
Circuit: prompts. The cursor appears to the right of the Bay: prompt.
Entering a l-digit number specifies the bay...

Customer Data Entry (CDE)
Form 15 -Dial-h Trunks
4.72This form specifies the characteristics of the system’s Dial-In
Trunks. This form also designates where incoming calls on
Dial-In Trunks are routed by modifying the incoming digits. Refer to
Table 4-28, Dial-In Trunks for form layout.
TABLE 4-28
FORM 15 
- DIAL-IN TRUNKS
CDE TERMINAL DISPLAY
4:26 PM 15-JAN-88alarm sttus = NO ALARMa’-
N-0
0
:D
-
Dl--
M-0
00D0
-
0-
-
)-
-
-
TENcotTK NAMEBAY SLT CClI
02 0203 0420205
f02 0606 0330604
x07 0701 02f08 0802...

SECTION MITL9109-094-210-NAcommence until the system receives the specified number of digits.
Note: This field must be filled for a DID Trunk. Otherwise, this field
defaults to 0.M: This field specifies the number of digits (0 to 8) that must be
absorbed after the incoming trunk is seized. The M field defaults to 0.
This field is applicable for any type of Dial-In Trunk.
X: This field specifies a maximum of two digits that may be inserted
before the digit string. This field is applicable for any type of...

Customer Data Entry (CDE)
6-CANCEL: This softkey appears after a programming error has oc-
curred. Pressing the CANCEL 
softkey returns the display to the level
where the programming error was made. The CANCEL softkey appears
with an error message.
7-BAY/SLT/CCT: Pressing this softkey locates a trunk via its bay, slot
and circuit numbers. The command line displays the Bay:, Slot: and
Circuit: prompts. The cursor appears to the right of the Bay: prompt.
Entering a l-digit number specifies the bay...

SECTION MITLSI 09-094-210-NAForm 16 
- Trunk Groups
4.75This form specifies the members of each Trunk Group by trunknumbers. The trunk number is assigned in Form 14 (refer to
Table 4-27, Non-Dial-In Trunks) and Form 15 (refer to Table 4-28,
Dial-In Trunks). The system supports a maximum of 50 Trunk Groups;
each group supports a maximum of 50 members. Refer to Table 4-29,
Trunk Groups for the form layout.TABLE 4-29
FORM 16 
- TRUNK GROUPS
CDE TERMINAL DISPLAY
4:26 PM 15-JAN-88alarm status = NO ALARM
[ GRP...