Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Customer Data Entry (CDE)
Secretarial Variants: When the cursor is at the SECRETARIAL field on
the command line, and when the TYPE field is set to Multiple, thesoftkeys display two selections (refer to Figure 4-12, Secretarial Vari-
ants). The two variants are secretarial and non-secretarial. Refer to
Section 
MITL9109-094-105-NA, Features Description for details. When
the variant has been chosen, move the cursor to the EXT NUM or
TRUI\!K NUMBER field, as appropriate.
I-NON SECR
6-QUIT
2-SECRETARIAL3-4-...

SECTION MITL9109-094-210-NAReview List for Form 09
4.42This form appears when the REVIEW softkey is pressed in the
Station/SUPERSET Telephones Form or the SUPERSET Tele-
phone Lines Form. When entered from the 
Station/SUPERSET Form,
this form displays a list of all programmed appearances of the selected
station extension number or 
SUPERSET Prime Line number. When en-
tered from the 
SUPERSET Telephone Lines Form, this form displays all
appearances of the selected key’s extension number or trunk...

Customer Data Entry (CDE)
KEY: For listed SUPERSET telephones, the KEY field displays the key
number where the line appears.
PRIME EXT NUM:This field displays the prime extension number
assigned to a particular Bay/Slot/Circuit.
4.44
C>mmands3-TRUNK NUMBER: This 
softkey selects a trunk by its trunk number.
Pressing this sof-tkey displays ENTER TRUNK NUM: prompt on the
command line. The trunk selection is completed by entering a valid
trunk number (1
- 200), and pressing the ENTER softkey.6-QUIT:...

SECTION MITL9109-094-210-NAForm 10 
-Pickup Groups
4.45This form specifies the members of each Pickup Group. Refer to
Table 4-17, Pickup Groups for the form layout. Memberships are
specified by the extension number of a Rotary Dial or DTMF set or the
Prime Line number of a 
SUPERSET telephone. Attendant Consoles arenot allowed. The SX-200 DIGITAL PABX with Generic 1003 software
supports a maximum of 50 Pickup Groups; each group supports a
maximum of 50 members.TABLE 4-17
4:26 P&l 15-JAN-88FORM 10 
-...

Customer Data Entry (CDE)NUM field. Enter a valid extension number and press the ENTER soft-
key.Note:
This softkey only appears if there is data present in this form.5-PICKUP GROUP: This 
softkey selects the Pickup Group to be dis-
played. Pressing the PICKUP GROUP softkey displays the ENTER PICKUPGROUP NUM: prompt on the command line. Enter the Pickup Group
number and press the ENTER softkey.6-QUIT: Pressing the QUIT 
softkey when editing this form returns the
display to the level before the field was...

SECTION MITLSI 09-094-210-NAForm 11
- Data Circuit Descriptor
4.48A data circuit descriptor specifies the parameters the data pro-
cessing software and attached DTE (Data Terminal Equipment)
require. This form provides 25 programmable descriptors. The main
form displays the descriptor numbers and the number of circuits asso-
ciated with each descriptor. (Refer to Table 4-18, Data Circuit Descrip-
tor). The system generates the data in this form based on the entries
in Form 12, Data Assignment. The user...

Customer Data Entry (CDE)
4.50 Commands
6-QUIT: Pressing the QUIT softkey at this level returns the display to
the Available Forms menu.
7-DESCRIPTOR NUMBER: The DESC NUM 
softkey allows the user to
select a DESC NUM by number. Pressing this 
sof-tkey displays the
ENTER DESC NUM: prompt. Entering a valid descriptor number and
pressing the ENTER 
softkey, completes the selection.
8-SELECT OPTION: Pressing this softkey displays a new form. This
form provides the options associated with the data circuit...

SECTION MITL9109-094-210-NAData Circuit Descriptor Options
4.51This form appears when the SEL. OPTION softkey is pressed
(refer to Table 4-18, Data Circuit Descriptor). It lists the pro-
grammable parameters of the descriptor. Refer to Table 4-19, Data
Circuit Descriptor Options.TABLE 4-19
DATA CIRCUIT DESCRIPTOR OPTIONS
CDE TERMINAL DISPLAY
12:17 PM 15-JAN-88alarm status = NO ALARM
1 DESCRI PTOR NLBIBER : 1 IPARAMETER NAME--lvnluESession Inactivity Disconnect TimerO-255 minutes
Guard TimerO-99 seconds...

Customer Data Entry (CDE)
DATA HAS BEEN CHANGED BUT NOT YET SAVED IN DATABASE--“ENTER”
TO SAVE
O-ENTER: This sof-tkey appears only after data for an entry has been
modified. Pressing the ENTER 
softkey commits each modification one
at a time to the database. After all changes have been completed, theuser must press the ENTER 
softkey again to commit all modifications
to the database.The other 
sof-tkeys depend on the parameter displayed on the com-
mand line. Generally:
lfor numeric parameters, only the...

SECTION MITLSI 09-094-210-NADATACIRCUITTABLE 4-20 
(CONT’D)DESCRIPTORS 
- PARAMETERSANDOPTIONSOFTKEYSParameter
Pooled Modem 
ConmunicationEstablished indicator
ASYNC: Keyboard Origination Allowed( Auto Baud 1ASYNC: ADL Auto BaudASYNC: Flow ControlASYNC: XCN character( o-127,
Decimal value of ASCII code 1
ASYNC :XOFF character( O-127,
Decimal value of ASCII code 1ASYNC :Break Key FunctionASYNC: PBX Attention Character ( 0- 127)ASYTUC: ParityASYTtC :Character Length(7-8;8 bits implies no parity 1ASYNC...