Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Customer Data Entry (CDE)
TABLE 4-1
LIST OF CUSTOMER DATA ENTRY FORMSNumberTitle
i:System Configuration
Feature Access Codes
03Class-of-Service Define
izSystem Options/System Timers
Tenant Interconnection Table
i;Tenant Night Switching Control
Console Assignments
i89Attendant LDN AssignmentsStations/SUPERSET Telephones10Pickup Groups
::Data Circuit Descriptor
Data Assignment13Trunk Circuit Descriptors14Non-Dial-In Trunks15Dial-In Trunks16Trunk Groups17Hunt Groups18Miscellaneous System Ports19Cal I...

SECTION MITL9109-094-210-NA
IO:15 PM 15-JAN-88TABLE 4-2
AVAILABLE FORMS
CDE TERMINAL DISPLAY
alarm status = NO ALARM
FORMS01 = SYSTEM 
CXINFIUJRATION02 = FEATURE ACCESS CODES
03 = CDS DEFINE04 = SYSTEM OPTIONS/SYSTEM TIMERS
05 = 
TOVAM INTERCONNECTION TABLE06 = TENANT NIGHT SWITCHING CONTROL07 = CWSOLE ASSIGNMENTS08 = AlXNDANT LDN ASSIGNMENTS
09 = STATI CINS/SUPERSET TELEPmWUES10 = PICKUP GROUPS11 = DATA CIRCUIT DESCRIPTOR12 = DATA ASSIGNMENTS
13 = 
TRUUK CIRCUIT DESCRIPTORS14 = NON-DIAL-IN TRUVKS15 =...

Customer Data Entry (CDE)Form 01- System Configuration
4.10 This form specifies the intended location of each peripheral
card for the system. Refer to Table 4-3, FORM 01 
- System
Configuration. If the peripheral cards are installed before the system is
programmed, this form enables the configuration of the system ac-
cording to the actual installation. If the system is programmed prior to
the peripheral card installation, then this form acts as a guide during
the installation process. If the installed...

SECTION MITL9109-094-210-NA
4.12Field DescriptionBAY, SLT and CCT: These fields specify the physical location of each
card type. The circuit number represents the physical location of each
module on the Universal Card.
PROGRAMMED: This field specifies the intendsd location of the re-
quired card types. Data can be assigned to the PROGRAMMED field
before the cards are installed.
INSTALLED: The data in the INSTALLED field reflects the actual in-
stalled cards. The system updates this field; the installer...

Customer Data Entry (CDE)
the selection and the PROGRAMMED field displays the COV LINE
prompt. The COV Line Card is a high power card and is restricted to
the upper slots of any digital bay. If the COV Line Card is placed in any
other slot, the system returns the following error message: High power
card cannot be programmed at Bay/slot/circuit - xx/xx/xx.
I-STATION2-3-
4-SUPERSET5-6-W IT7-8-
9-O-Figure 4-3 Other Line Card Types for Analog Bays
1 -STATION:Pressing the STATION 
softkey programs the...

SECTION MITL9109-094-Zl O-NAan error message if this card is placed in any other slot.
I-CO 
TRU’IK6-QUIT2-3-E&MTRWIK4-6DID/TIE5-
7-8-
9-O-Figure 4-5 Other Trunk Card Types
I-CO TRUNK: Pressing the CO TRUNK 
softkey programs the selected
card slot as a CO Trunk Card. Pressing the ENTER 
softkey completes
the selection and the PROGRAMMED field displays the CO TRUNK
CARD prompt.
3-E 
& M TRUNK: Pressing the E & M TRUNK softkey programs the
selected card slot as an E&M Trunk Card. Pressing the ENTER...

Customer Data Entry (CDE)Note:The system automatically programs DTMF Receivers where
they are installed, provided nothing is already programmed
for that circuit.
4-SYSTEM TYPE:The SX-200 DIGITAL Generic 1003 software can
support 4 system variants, two of which are interchangeable;
336 Port 
- This variant is digital and cannot be changed.
456-Port 
- This variant can be interchanged with the 480-port.
480-Port - This variant can be interchanged with the 456-port.
672-Port 
- This variant is digital and...

SECTION MITL9109-094-210-NA6-CANCEL: This 
softkey appears after a programming error has oc-
curred. Pressing the CANCEL 
softkey returns the display to the level
where the programming error was made. The CANCEL 
softkey appears
with an error message. Refer to Table 5-1, Programming Error Mes-
sages for a list of these error messages.
7-BAY/BLT/CCT: Instead of moving the line pointer to the desired line
of the form, the programmer can call it up directly by specifying the
bay, slot and circuit.
Pressing...

Customer Data Entry (CDE)
Form 02- Feature Access Codes
4.14This form specifies the Feature Access Codes for the system
(refer to Table 4-4, Feature Access Codes). Feature Access
Codes can be a maximum of 
five digits (except Callback Busy and
Executive Busy Override access codes which must be only one digit).
The codes must be unique; they cannot match any listed directory
number or other access code in the system. Refer to Table 4-5,
Programmable Feature Access Codes for a complete list of the access...

SECTION MITL9109-094-210-NA4.16 Commands
4-TOP: Pressing the TOP 
softkey moves the line pointer to the first
line of the form. The command line displays the first line.
5-BOTTOM: Pressing the BOTTOM 
softkey moves the line pointer to
the last line of the form. The command line displays this line.
6-QUIT: Pressing the QUIT 
softkey when editing this form returns the
display to the level before the field was modified. The change is not
saved. At all other times, pressing this 
softkey exits Form 02 and...