Minolta Di450 User Manual

							6-44
When a Message Appears
Chapter 6
6. When the Message “Malfunction Detected.” Appears
Malfunction Resetting Procedure
4003P200CA
When a screen as shown on the left appears on the
Touch Panel, it indicates that the machine has
developed a minor malfunction.
Turning OFF, then ON, the machine will reset the
minor malfunction.
IMPORTANT
If this does not reset the minor malfunction, call
your Technical Representative and give him or
her the malfunction code being shown on the
To u c h Pa n e l .
4003P201CA
When a screen as shown on the left appears on the
Touch Panel, it indicates that the machine has
developed a malfunction.
Call your Technical Representative.
IMPORTANT
When you call your Technical Representative, be
sure to give him or her the malfunction code
being shown on the Touch Panel.
Downloaded From ManualsPrinter.com Manuals 
						

							6-45
When a Message Appears
Chapter 6
7. What Does Each Message Mean?
What does each message mean?
Message Cause Action
Malfunction detected. Call your
Technical Rep. and provide
code:The machine malfunctioned
and is unable to make copies.Call and inform your Technical
Representative of the code
being shown on the Touch
Panel.
Please add toner.
Follow the instructions on label
inside of Front Door.Toner has run out and the
machine is unable to make
copies.Replace the Toner Bottle with a
new one. (“When the Message
‘Please add Toner.’ Appears”

 p. 6-6)
Please add toner. Toner is soon running out. Replace the Toner Bottle with a
new one. (“When the Message
‘Please add Toner.’ Appears”

 p. 6-6)
Stapler empty. Replace Staple
Cartridge or cancel Staple
mode.The staples have run out. Replace the Staple Cartridge
with a new one. (“When the
Message ‘Stapler is empty.’
Appears”
p. 6-8)
Preventative maintenance time. The time has come when the
machine needs service.Call your Technical
Representative.
Your account has reached its
maximum copy allowance.
Please call your administrator.The max. number of copies that
can be made for your account is
determined in the Administrator
Mode.Contact the administrator of
your machine. (Administrator
Mode of Utility Mode

p. 5-19)
Return the following # of
originals to Document Feeder:
# Sheet(s)After a misfed sheet of paper
has been cleared, you need to
reload the originals fed out onto
the Document Exit Tray onto
the Document Handling Tray.Add the number of originals
indicated to the bottom of the
remaining stack and reload.
Image data has caused memory
overflow. Your copy job has
been canceled.Themachineisunabletoscan
the data for lack of memory.Wait until a print cycle is run or
erase a reserved job to make
room for new data.
Original left on the Glass. You have left an original on the
Original Glass.Remove the original from the
glass.
This mode cannot be selected
with the .You have set two functions that
conflict with each other.Cancel either one of the two
functions.
Downloaded From ManualsPrinter.com Manuals 
						

							6-46
When a Message Appears
Chapter 6
8. When This Type of Copy is Produced
When this type of copy is produced
Symptom Possible Cause Action
The image is too light. The exposure level for the Auto
Exposure mode is set at
“Lighter.”Change the setting of “Auto
Default Level” of User’s Choice.

p. 5-14
Or, cancel the Auto Exposure
mode and select Manual
Exposure to adjust the exposure
level to obtain a darker image.

p. 3-44
The exposure level for the
Manual Exposure mode is set at
“Lighter.”Touch [Darker] as necessary to
obtain a darker image.
p. 3-44
You have been making copies
from a photo or an original with
a large dark area.The machine needs more toner.
Replenish toner by using Toner
Replenisher of Utility Mode.

p. 5-11
The Toner Bottle has just been
replaced.The machine needs more toner.
Replenish toner by using Toner
Replenisher of Utility Mode.

p. 5-11
The message “Replenish Toner.”
isshownontheTouchPanel.Replace the Toner Bottle.

p. 6-6
The paper is damp. Change the paper.
p. 6-2
The image is too dark. The exposure level for the Auto
Exposure mode is set at
“Darker.”Change the setting of “Auto
Default Level” of User’s Choice.

p. 5-14
Or, cancel the Auto Exposure
mode and select Manual
Exposure to adjust the exposure
level to obtain a lighter image.

p. 3-44
The exposure level for the
Manual Exposure mode is set at
“Darker.”Touch [Lighter] as necessary to
obtain a lighter image.
p. 3-44
The Original Glass surface is
dirty.Wipe the Original Glass clean
with a soft dry cloth.
p. 7-10
The original is not held tightly
against the Original Glass.Place the original in position so
that it is held tightly against the
Original Glass.
p. 3-6
The copy is blurry. The paper is damp. Change the paper.
p. 6-2
1074O110
1074O109
1074O110
Downloaded From ManualsPrinter.com Manuals 
						

							6-47
8. When This Type of Copy is Produced
When a Message Appears
Chapter 6
* Call your Technical Representative if these procedures do not correct the problem.Symptom Possible Cause Action
The copy has lines.
The copy has dark specks or spots.
The Original Glass is dirty. Wipe the Original Glass clean
with a soft dry cloth.
p. 7-10
The Original Pad is dirty. Wipe the Original Pad clean with
a soft cloth dampened with
alcohol.
p. 7-10
The original is very thin or
highly transparent.Place a blank sheet of paper over
the original.
p. 3-6
The original is 2-sided. The information on the back side
of a 2-sided, thin original may be
slightly reproduced on the copy.
Set the machine into the Manual
Exposure mode and, using
[Lighter], make the exposure
level lighter.
p. 3-44
The edge of the copy is dirty. The Original Pad is dirty. Wipe the Original Pad clean with
a soft cloth dampened with
alcohol.
p. 7-10
You have selected a paper size
larger than the original. (When
the zoom ratio is set at full size
×1.000)Select the same paper size as the
original.
p. 3-9
Or, use Auto Size to enlarge the copy
to the appropriate size.

p. 3-14
The original is not placed in the
correct position (when the zoom
ratio is set at full size
×1.000).Select the same paper size as the
original. Or, reload the paper in
the same direction as the
original.
p. 3-9
The reduction ratio selected is
not in accord with the paper size.
(When doing manual reduction
copying.)Select the zoom ratio according
to the paper size.
p. 3-14
Or, use Auto Size to reduce the copy
to the appropriate size.

p. 3-14
The image on the copy is not
aligned properly
.
The original is not placed in the
correct position.Place the original correctly on
the Original Glass against the
Original Width Scale.
p. 3-6
Or, load it in the Electronic
Document Handler correctly
along the Document Guide
Plates.
p. 3-5
The originals may not be
suitable for use in the Electronic
Document Handler.Raise the Electronic Document
Handler and place the originals
on the Original Glass one at a
time, instead of using the
Electronic Document Handler.

p. 3-5
Something is sticking to the
Original Glass.Wipe the Original Glass clean
with a soft dry cloth.
p. 7-10
1139O1670A
1074O111
1074O112
1074O113
Downloaded From ManualsPrinter.com Manuals 
						

							6-48
When a Message Appears
Chapter 6
9. The Machine is not Functioning as Designed
The machine is not functioning as designed
* If these procedures do not correct the problem, turn OFF the Power Switch, unplug the power cord from
the power outlet, and contact your Technical Representative.Symptom Check for Action
The Touch Panel shows nothing. Is only the Start key lit up green? The machine is in the Energy
Saver mode. Press any key on
the control panel to cancel
Energy Saver mode.
Auto Shut Off is activated. Turn the Power Switch ON.
The Display Contrast Knob is
turned to the excessively light or
dark position.Viewing the Touch Panel, adjust
the Display Contrast Knob as
necessary.
The Start key does not light up
green.Is your Access Number or
Account Number entered?Enter your Access Number or
Account Number by following
the procedure given in “Entering
the Access Number.”

p. 2-20
No copies are fed out when the
Start key is pressed.The machine has developed a
malfunction.Check the Touch Panel and take
action according to the message
on the panel.
The machine was just turned ON
and is warming up.It takes the machine about 4 min.
to be ready for making copies
after it has been turned ON.
Please wait.
Control panel keys do not
respond.The Interrupt key LED is lit up. The machine is in the interrupt
mode. Press the Interrupt key to
cancel the interrupt mode.
The machine is not activated
when the Power Switch is turned
ON.The power cord is left unplugged
from the power outlet.Plug the power cord into the
power outlet.
The room circuit breaker is
open.Close the room circuit breaker.
4003P141CA
1166O260AA
Downloaded From ManualsPrinter.com Manuals 
						

							7-1
Chapter 7 Miscellaneous
Chapter 7
Miscellaneous
Downloaded From ManualsPrinter.com Manuals 
						

							7-2
Chapter 7 Miscellaneous
1. Specifications
Specifications
Di450/Di550
Di450 Di550
Type Console Copier/Printer
Platen Type Stationary
Photoconductor OPC
Copying System Electrostatic Dry Powdered Image Transfer to Plain Paper
Developing System Micro-Toning System
Fusing System Lamp-Heated Roller
Resolution 600dpi
Types of Original Sheets, books and other three-dimensional objects
Maximum original size : 11×17 Lengthwise
Maximum original weight : 6-1/2 lb
Kinds of Paper Plain paper (16 lb to 24 lb), recycled paper
Exclusive paper : Thick paper (24-1/4 lb to 41-3/4 lb), translucent paper,
OHP transparencies
*Exclusive paper can only be used for the Multi Bypass Tray.
Copy Paper Size 1st Drawer/2nd Drawer : 11×17L to 5-1/2×8-1/2L
Intelligent Multi Bypass Tray : Crosswise : 4 to 11-3/4
Lengthwise : 5-3/4 to 17
Paper Feeding System 1st Drawer/2nd Drawer : 550 sheets (20 lb)
Intelligent Multi Bypass Tray : 50 sheets (20 lb),
20 sheets (recycled paper or exclusive paper)
Warm-up Time 240 seconds or less
First Copy LetterC = 4 seconds or less (in full size mode using 1st Drawer)
Copy Speed
(Approx. copies/min)Full size (x1.000)
11×17L : 28
LegalL :32
LetterL : 38
LetterC : 45Full size (x1.000)
11×17L : 31
LegalL :37
LetterL : 45
LetterC : 55
Zoom Ratios Fixed ratios, Full size: 1:1±0.005
Reduction ratios :×0.500,×0.647,×0.733,×0.785,×0.930
Enlargement ratios :×1.214,×1.294,×1.545,×2.000
Variable ratios : From×0.250 to×4.000 in×0.001 increments
Multiple Copies Up to 999 copies (count-down system)
Exposure Control Auto Exposure Mode, Manual Exposure Mode, Text Exposure Mode,
Text/Photo Exposure Mode and Photo Mode
Lost Image 1-sided copy in the full size mode
Leading Edge, 1/8 Trailing Edge, 1/8 Rear Edge, 1/8
Power Requirements AC120V, 220V-240V; 50/60Hz
Power Consumption 1.43kW
Dimensions Width : 26-1/4 Depth : 29-1/4Height : 40-3/4
Weight 249 lb
Downloaded From ManualsPrinter.com Manuals 
						

							7-3
1. Specifications
Chapter 7 Miscellaneous
2 Way Paper Feed Cabinet PF-208
KindsofPaper Plainpaper(16lbto24lb),recycledpaper
Paper Size Duplex Unit : 11×17L to 5-1/2×8-1/2L
3rd Drawer : 11×17L to 5-1/2×8-1/2L
4th Drawer : 11×17L to LetterL
Capacity 3rd Drawer : 550 sheets (20 lb)
4thDrawer :550sheets(20lb)
Power Source Supplied from copier
Dimensions Width :26-1/4Depth :28-3/4Height :15-1/4
Weight 100-1/4 lb
Large Capacity Cabinet PF-115
KindsofPaper Plainpaper(16lbto24lb),recycledpaper
Paper Size Duplex Unit : 11×17L to 5-1/2×8-1/2L
3rd Drawer : LetterC
Capacity 3rd Drawer : 2,600 sheets (20 lb)
Power Source Supplied from copier
Dimensions Width :26-1/4Depth :28-3/4Height :15-1/4
We i g h t105lb
Duplexing Paper Feed Cabinet PF-7D
KindsofPaper Plainpaper(16lbto24lb),recycledpaper
Paper Size Duplex Unit : 11×17L to 5-1/2×8-1/2L
Power Source Supplied from copier
Dimensions Width :26-1/4Depth :28-3/4Height :15-1/4
Weight 82-3/4 lb
Electronic Document Handler EDH-3
Document Feeding System Standard Mode : 1-sided original, 2-sided original
Mixed Original Detection Mode : 1-sided Mixed Original Detection
2-sided Mixed Original Detection
Single Feeding Mode : 1-sided original
Kinds of Original Plain paper
1-sided original : 13-1/4 lb to 29-1/4 lb
2-sided original, Mixed Original Detection : 16 lb to 24 lb
SingleFeeding :9-1/4lbto41-3/4lb
Original Size 1-sided, 2-sided original, Single Feeding : 11×17L to 5-1/2×8-1/2L
Mixed Original Detection : 11×17L to Letter
Capacity of Document
Handling TrayUp to 100 sheets (20 lb)
Power Source Supplied from copier
Power Consumption 72W or less
Dimensions Width : 26 Depth : 22-3/4 Height : 5-1/2
Weight 28-3/4 lb
Downloaded From ManualsPrinter.com Manuals 
						

							7-4
1. Specifications
Chapter 7 Miscellaneous
Finisher FN-105
Types of Trays Top Offset Tray, Bottom Offset Tray
Modes Non-Sort Mode, Sort Mode, Group Mode, Staple Mode, Hole Punch Mode
Kinds of Paper Top Offset Tray
Non-Sort Mode
 Plain paper (16 lb to 24 lb), recycled paper
 Exclusive paper
Thick paper (24-1/4 lb to 41-3/4 lb), translucent paper, OHP
transparencies
Hole Punch Mode
 Plain paper (16 lb to 24 lb), recycled paper
Bottom Offset Tray
Sort Mode, Group Mode
 Plain paper (16 lb to 41-3/4 lb), recycled paper
Staple Mode, Punch Mode
 Plain paper (16 lb to 24 lb), recycled paper
Paper Size Top Offset Tray : 11×17L to 5-1/2×8-1/2
Bottom Offset Tray : 11×17L to Letter
Capacity Top Offset Tray
 Plain paper (20 lb), recycled paper
: Max. paper size 11×17L to 5-1/2×8-1/2, 250 sheets
 Exclusive paper
: Thick paper, translucent paper, OHP transparencies = 20 sheets each
Bottom Offset Tray
 Plain paper (20 lb), recycled paper
: LetterL or smaller, 3,000 sheets
: Larger than LegalL, 1,500 sheets
Stapling Acceptable paper size : 11×17L to Letter
Acceptable number of copies : 2 to 50 sheets
Punching Acceptable paper size : 11×17L to Letter

Punch Hole : 2-Hole or 3-Hole

Punch Hole : 2-Hole
Power Source Supplied from copier
Power Consumption 63W or less
Dimensions Width : 21-1/4 Depth : 24-3/4 Height : 38-1/2
Weight Finisher : 86-1/2 lb
Accessories Staple Cartridge, 5,000 staples/cartridge× 2 pieces
Downloaded From ManualsPrinter.com Manuals 
						

							7-5
1. Specifications
Chapter 7 Miscellaneous
Finisher FN-106
Types of Trays Top Offset Tray, Bottom Offset Tray
Modes Non-Sort Mode, Sort Mode, Group Mode, Staple Mode
Kinds of Paper Top Offset Tray
Non-Sort Mode
 Plain paper (16 lb to 24 lb), recycled paper
 Exclusive paper
Thick paper (24-1/4 lb to 41-3/4 lb), translucent paper, OHP
transparencies
Bottom Offset Tray
Sort Mode, Group Mode
 Plain paper (16 lb to 41-3/4 lb), recycled paper
Staple Mode
 Plain paper (16 lb to 21-1/4 lb), recycled paper
Paper Size Top Offset Tray : 11×17L to 5-1/2×8-1/2
Bottom Offset Tray : 11×17L to Letter
Capacity Top Offset Tray
 Plain paper (20 lb), recycled paper
: Max. paper size 11×17L to 5-1/2×8-1/2, 250 sheets
 Exclusive paper
: Thick paper, translucent paper, OHP transparencies = 20 sheets each
Bottom Offset Tray
 Plain paper (20 lb), recycled paper
: LetterL or smaller, 1,000 sheets
: Larger than LegalL, 500 sheets
Stapling Acceptable paper size : 11×17L to Letter
Acceptable number of copies : 2 to 30 sheets
Power Source Supplied from copier
Power Consumption 63W or less
Dimensions Width : 21-1/4 Depth : 24-3/4 Height : 38-1/2
Weight Finisher : 78-1/4 lb
Accessories Staple Cartridge, 3,000 staples/cartridge×1 piece
Downloaded From ManualsPrinter.com Manuals