Minolta Di450 User Manual

							5-10
2. Image Memory Input
Using the Utility Mode
Chapter 5
Press the Utility key.
Touch [Job/Image/Scan Input].
Touch [Image Memory Input].Touch [Delete], then touch the number key to
be deleted.
To u c h [ E n t e r ] .
Deleting a Programmed Image
1
4002O282CA
2
4003P142CA
3
4003P152CA
4
4003P465EC
5
Downloaded From ManualsPrinter.com Manuals 
						

							5-11
Using the Utility Mode
Chapter 5
3. Meter Count and Toner Replenisher
Meter Count
Touching [Meter Count] allows you to check the total count of each of the following seven counters
recorded since the installation of the machine.
Shows the total number of prints made since the
installation of the machine.
Shows the number of prints made on paper of a
preset size. (The size will be set by your Technical
Representative.)
Shows the number of 2-sided prints made.
Shows the number of 2-sided prints made on paper
ofapresetsize(thesamesizeasthatsetforthe
Size Counter.)Shows the total number of prints made by the
active accounts.
Shows the number of prints produced by the
machine configured as a printer.
Shows the number of prints produced by the
machine configured as a printer on paper of a size
preset for Size Counter.
(This counter counts the number of prints made on
paper of the same size as that set for the Size
Counter.)
Toner Replenisher
Touching [Toner Replenisher] sets the machine into the auxiliary toner replenishing mode.
The machine tends to exhaust the supply of toner rapidly when printing a large number of pages using an
original with dark solid areas such as a photo. As a result, the printed image density will become lighter.
In such a case, you can use Toner Replenisher to regain the normal image density quickly.
NOTES
 Do not turn OFF the Power Switch or open the Front Door while the machine is replenishing toner.
 Toner is not replenished if the image density is sufficiently high.
 The toner replenishing sequence ends automatically.
Total Counter
Size Counter
2-Sided Total Counter
2-Sided Size Counter
Account Total Counter
Printer Total Counter
Printer Size Counter
Downloaded From ManualsPrinter.com Manuals 
						

							5-12
Using the Utility Mode
Chapter 5
4. User’s Choice
The machine has been set so that the most frequently used settings are automatically selected in the initial
mode. User’s Choice allows you to select the default settings which are automatically selected in the
initial mode according to your own needs. This saves time and effort to make extra settings when the
machine is turned ON or Auto Panel Reset is activated.
For more details, consult your Technical Representative.
User’s Choice Functions
[1/6]
 p.5-13
[2/6]
 p.5-14
[3/6]
 p.5-15[4/6]
 p.5-15
[5/6]
 p.5-16
*1: Sleep is shown when the Printer Controller
is mounted.
[6/6]
 p.5-16 A listing of User’s Choice functions is given in six
pages of menu, from[1/6] to [6/6]. To show the
listing of each page, touch the desired page
number key at the bottom of the Touch Panel.
4003P466EA
Original Copy Default
Language Selected
Mixed Original Detect
Memory Recall
Auto Paper/Auto Size
Tray Priority
2in1, 4in1, Booklet Copy Zoom
Density Priority
Default Level
Output Priority
Intelligent Sorting
Criss Cross Mode
“Small” Originals
4in1 Copy Order
Date Printing Format
Date Printing Position
Page Number PositionConfirmation Beep
Universal Tray
Special Paper
Auto Panel Reset
Energy Save Mode
Plug-in Counter Reset
Auto Shut OFF *1
Date/Time Set
Print Exposure
Priority Device
Density (ADF)
Priority Offset Tray
Downloaded From ManualsPrinter.com Manuals 
						

							5-13
4. User’s Choice
Using the Utility Mode
Chapter 5
Useful Tip
When“100 Accounts” is selected, the User’s
Choice functions of [1/6] to [4/6] can be set for
each account after the corresponding access
code has been entered. (In this case, the listing of
User’s Choice displayed on the Touch Panel is
from [1/4] to [4/4].)
The administrator can make the User’s Choice
settings in common with all 100 accounts after
“100 Accounts” has been selected.
➀With the Touch Panel prompting you to enter
the access code, press the Utility key.
➁Touch [User’s Choice].
➂Enter the administrator number from the 10-
Key Pad.
* This allows the administrator to make the
settings for [1/6] to [6/6].
NOTE
The User’s Choice settings in common with 100
accounts for [1/6] to [4/6] are not valid for the
accounts for which the individual User’s Choice
settings have been made after “100 Accounts”
was selected.[1/6]
Specify the original copy type automatically
selected when power is turned ON or panel reset.
The initial setting is “1-Sided 1-Sided.”
Select the language of the Touch Panel messages.
The initial setting is “English.”
Select whether to default to Mixed Original
Detection (“ON”) or not (“OFF”) when power is
turned ON or panel reset.
The initial setting is “OFF.”
* If the following combination is set at a time in
User’s Choice, the Mixed Orig. Detect will be
automatically canceled and the copies are
made in Single-Sided Double-Sided copy
mode.
 Original Copy Default: Single-Sided
Double-Sided
 Mixed Orig. Detect: ON
Select whether to enable (“ON”) the function that
allows you to use the same image data of the copy
cycle that has just been completed or not (“OFF”).
The initial setting is “OFF.”
Specify the default mode selected automatically
when power is turned ON or panel reset, either
“Auto Paper,” “Auto Size,” or “Manual.”
The initial setting is “Auto Paper.”
Select the default paper source that is
automatically selected.
The initial setting is “1” (1st Drawer).
Original Copy Default
Language Selected
Mixed Original Detect
Memory Recall
Auto Paper/Auto Size
Tr a y P r i o r i t y


  

Downloaded From ManualsPrinter.com Manuals 
						

							5-14
4. User’s Choice
Using the Utility Mode
Chapter 5
[2/6]
Select whether to enable (“ON”) or disable
(“OFF”) recalling a default zoom ratio for 2in1,
4in1, or Booklet Creation. Setting is possible for
“2in1/4in1” and “Booklet Creation.”
 “2in1/4in1”
Default zoom ratios:
2in1: 0.647
4in1: 0.500
The initial setting is “ON.”
 “Booklet Creation”
Default zoom ratios:
Booklet Creation: 0.647
The initial setting is “ON.”
Select the default density setting selected
automatically in the initial mode. Select either
“Auto” or “Manual” for the exposure mode and
“Text,” “Text/Photo,” or “Photo” for the image
quality setting.
The initial settings are “Auto” for the exposure
mode and “Text” for the image quality setting.
* “Auto” cannot be combined with “Text/
Photo” or “Photo.”
Auto
Select the default exposure level in the Auto
Exposure mode, either “Lighter,” “Normal,” or
“Darker.”
The initial setting is “Normal.”
Manual
Set the default exposure level in the Manual
Exposure mode.
The initial setting is “5.”
* With EXP5 at the central level, the exposure
level will become lower as the number
becomes smaller, and it will become higher as
the number becomes greater.Select the default combination of the finishing
type when the machine is equipped with a Finisher
from among the followings:

Non-Sort, Sort, or Group
Hole Punch (only when FN-503/FN-5 is mounted)
2-Hole Punch (only when FN-105 is mounted)
3-Hole Punch (only when FN-105 is mounted)
Corner Staple
2-Point Staple (only when FN-105/FN-5 is
mounted)

Non-Sort, Sort, or Group
Hole Punch (only when FN-105/FN-503/FN-5 is
mounted)
Corner Staple
2-Point Staple (only when FN-105/FN-5 is
mounted)
The initial setting is “Non-Sort.”
Select whether to turn “ON” or “OFF” the
function that automatically switches between Sort
and Non-Sort. It selects Non-Sort if only a single
original is loaded and Sort if two or more originals
are loaded in the Electronic Document Handler.
The initial setting is “ON.”
Select whether to enable (“ON”) or disable
(“OFF”) crisscross sorting when the conditions for
crisscross sorting are met and Sort or Group is
selected.
The initial setting is “ON.”
2in1, 4in1, Booklet Copy Zoom
Density Priority
Default Level
4003P167CA
Output Priority
Intelligent Sorting
Criss Cross Mode
Downloaded From ManualsPrinter.com Manuals 
						

							5-15
4. User’s Choice
Using the Utility Mode
Chapter 5
[3/6]
Select whether to enable (“ON”) a copy cycle or
not (“OFF”) when it is initiated by pressing the
Start key with no originals placed on the Original
Glass or with an original smaller than the
detectable size placed on the glass in the Auto
Paper mode.
If this function is turned “ON,” the copy cycle is
run using the paper loaded in the default paper
source. If turned “OFF,” a warning message
appears to instruct the user to select the paper.

The initial setting is “ON.”

The initial setting is “OFF.”
Select the default copying order in the 4-in-1 mode
from among the following two:
The initial setting is “ ”
Select the format for date printing, i.e.,
“punctuation,” “year,” and “date format.”
 “Punctuation” can be either “XX/XX/XX” or
“XX.XX.XX.”
The initial setting is “XX/XX/XX.”
 “Year” can be either “’yy” or “yyyy.”
The initial setting is “’yy.”
 “Date Format” can be either “’00/12/27,” “12/
27/’00,” “DEC/27/’00,” “27/12/’00,” or “27/
DEC/’00.”
The initial setting is “’00/12/27.”Enter the position at which to print the date by X
andYusing[]or[]. The dimension can range
from 3/16 to 1-9/16.
The initial setting is “X: 1/4, Y: 3/4.”
Enter the position at which to print the page
number using []or[]. It can range from 3/16
to 1-9/16 from the bottom of the page.
The initial setting is “1/4.”
[4/6]
Select whether to turn “ON” or “OFF” the beep
that sounds each time a key on the Touch Panel is
touched.
The initial setting is “ON.”
“Small” Originals
4in1 Copy Order
Date Printing Format
12
3413
24
12
34
Date Printing Position
Page Number Position
Confirmation Beep
Downloaded From ManualsPrinter.com Manuals 
						

							5-16
4. User’s Choice
Using the Utility Mode
Chapter 5
[5/6]
Select either “Auto Detect” or “Size Input” for the
size of the paper loaded in the Universal Tray.
The initial settings are as follows:
1st Drawer: “Auto Detect”
2nd Drawer: “Auto Detect”
Designate a drawer for special paper.
The initial setting is “Normal” for all drawers.
See p. 3-10 for Special Paper Setting.
Select the time it takes the auto panel reset
function to be activated from among “30 seconds,”
“1 min.,” “2 min.,” “3 min.,” or “5 min.,” or not
activate the function at all (“No Reset”).
The initial setting is “1 min.”
Set the time it takes the machine to enter the
Energy Saver mode, from 1 min. to 90 min. (in 1
min. increments).
The initial setting is “15 min.”
Select whether to reset the panel (“ON”) or not
(“OFF”) when the Plug-In Counter is pulled out of
the machine.
The initial setting is “ON.”

Auto Shut Off shuts down the machine a given
period of time after the last operation.
Select the time it takes the Auto Shut Off function
tobeactivated,from15min.to90min.in1min.
increments.
The initial setting is “90 min.”
* A setting is also possible to disable Auto Shut
Off.
Select the time it takes the machine to
automatically enter the Sleep mode from 15 to 90
min. in 1 min increments.
The initial setting is “90 min.”
* The Sleep function can even be disabled.
[6/6]
Set the date and time-of-day.
The initial setting is “2000/10/01,00:00:00.”
Select the print exposure level from among
“Lighter,” “Normal,” or “Darker.”
The initial setting is “Normal.”
Select the configuration of the machine, either as a
“Copier” or “Printer.”
The initial setting is “Copier.”
Select the image density level when the Electronic
Document Handler is used, either Mode 1 or Mode 2.
Select the density level according to the original,
either “Mode 1” or “Mode 2.”
The initial setting is “Mode 2.”
Mode 1: Used for the standard original, such as a
word-processor made document.
Mode 2: Effective in reproducing a pale original,
such as a faint pencil-written document.

Select the output tray into which copied paper is to
be fed, either “Top Tray” or “Bottom Tray.”
The initial setting is “Top Tray.”
Universal Tray
Special Paper
Auto Panel Reset
Energy Save Mode
Plug-In Counter Reset
Auto Shut Off
Sleep
Date/Time Set
Print Exposure
Priority Device
Density (ADF)
Priority Offset Tray
:Mode1: Mode 2
Downloaded From ManualsPrinter.com Manuals 
						

							5-17
4. User’s Choice
Using the Utility Mode
Chapter 5
Making the User’s Choice Settings
Press the Utility key.
Touch [User’s Choice].
Select the key of the page number on which
the desired User’s Choice function is listed.
For example, to change Output Priority from
Non-Sort to Sort, touch [2/6].Touch the key of the desired User’s Choice
function.
For example, touch [Output Priority].
To u c h [ S o r t ] .
To u c h [ E n t e r ] .
*Repeat steps 3 to 6 to make new settings for
other User’s Choice functions.
Touch [Exit].1
4002O282CA
2
4003P168CA
3
4003P169CA
4
4003P170CA
5
4003P471EA
6
7
Downloaded From ManualsPrinter.com Manuals 
						

							5-18
Using the Utility Mode
Chapter 5
5. Administrator Mode
This mode is used only by the administrator of your machine. When Administrator Mode is selected, the
machine prompts you to enter your “Administrator’s #.” The following functions can be set only when
the correct administrator number is entered.
NOTES
 The administrator number is to be programmed by your Tech. Rep. Ask him/her for more details.
 The administrator of this machine should remember the administrator number.
Selecting the Administrator Mode
Press the Utility key.
Touch [Administrator Mode].
Enter the administrator number from the 10-
Key Pad and touch [Enter].The Touch Panel now shows the detailed
functions that can be set under Administrator
Mode.1
4002O282CA
2
4003P172CA
3
1149O235AC
4
4003P473EA
Downloaded From ManualsPrinter.com Manuals 
						

							5-19
5. Administrator Mode
Using the Utility Mode
Chapter 5
Administrator Mode Functions
This function is used to control the number of
pages printed according to the account.
Select whether to turn “ON” or “OFF” the Copy
Track function for “Copier” or “Printer” and select
the Copy Track method, either “100 Accounts” or
“1000 Accounts.”
The initial setting is “OFF.”
When“100 Accounts” is selected:

Access Code:
You can program or change your access code
(for a max. of 100 accounts).

Account No.:
Program or change the account number.

Copy Limit:
You can limit the maximum number of prints
that can be made.

Total Count:
Displays the count of the Total Counter. You
can also clear the counter.

Size Count:
Displays the count of the Size Counter. You can
also clear the counter.
When“1000 Accounts” is selected:

Total Count:
Displays the count of the Total Counter. You
can also clear the counter.This function is used to limit the number of pages
that can be printed at one time (number of sets of
printed pages).
The initial setting is “OFF.”

This function can disable the Auto Shut Off
function. Select whether to enable (“YES”) or
disable (“NO”) the Non-Auto Shut Off function.
The initial setting is “No” (disable).

Select whether to enable (“Yes”) or disable (“No”)
the setting that disables Sleep.
The initial setting is “No” (disable).
Copy Track
Copy Track Data
Max. Copy Set
Disable Auto Shut Off
Disable Sleep
Downloaded From ManualsPrinter.com Manuals