Minolta Di450 User Manual

							6-4
1. When the Message “Replenish paper.” Appears
When a Message Appears
Chapter 6
Slide out the 3rd (or 4th) Drawer.
Load the paper stack into the drawer so that
its front side faces down.
NOTE
The paper should be
loaded no higher than the

(Max. Level Indicator).
Slide the drawer back in.
3rd Drawer/4th Drawer
(5-Way Type)
1
4002O163AB
2
4002O164AB
Max.
1145O555KA
3
4002O165AC
Downloaded From ManualsPrinter.com Manuals 
						

							6-5
1. When the Message “Replenish paper.” Appears
When a Message Appears
Chapter 6
Holding the Lock Release Lever, open the
Cassette Door.
When adding paper to a partially loaded cassette,
press the Paper Plate Descent key to lower the
Paper Plate before opening the Cassette Door.
Place the paper stack onto the Paper Plate so
that its front side faces up.
NOTES
 Make sure that the leading edge of the paper
stack is pressed tightly up against the Guide
Plate on the take-up side of the cassette.
 The paper should be loaded no higher than
the

(Max. Level Indicator).
Close the Cassette Door.
* This causes the Paper Plate to rise
automatically.
NOTE
The Paper Plate may not ascend if the Cassette
Door is not closed completely. Be sure to close
the door completely.
Large Capacity Cassette
1
4002O166AC
4002O167AC
2
4002O168AC
Max.
1145O555KA
CAUTION
If the Paper Plate Descent key is
pressed while the Paper Plate is moving
upward, the Paper Plate starts moving
downward. When the key is pressed a
second time thereafer, the Paper Plate
stops moving down.
3
4002O169AC
Downloaded From ManualsPrinter.com Manuals 
						

							6-6
When a Message Appears
Chapter 6
2. When the Message “Please add Toner.” Appears
Replacing the Toner Bottle
Swing down the Front Door.
Swing open the Toner Bottle Holder and pull
out the used Toner Bottle.Tap a new Toner Bottle against a desk or
other hard surface four to five times. Then,
turn the Toner Bottle upside down and tap it
in the same way again.
Shake the new Toner Bottle well and turn it
over lengthwise five times.
4003P185CA
The message shown on the left appears when toner
is soon running out.
It is recommended therefore that you replace the
Toner Bottle as soon as possible.
You can still make prints, but the image density
will become lighter and lighter.
4003P186CA
When toner has run out, the message shown left
appears and you can no longer start a new print
cycle.
Replace the Toner Bottle with a new one by
following the procedure given below.
1
4002O170AB
2
4002O171AB
3
4002U099AA
4
1075O266AA
Downloaded From ManualsPrinter.com Manuals 
						

							6-7
2. When the Message “Please add Toner.” Appears
When a Message Appears
Chapter 6
With the “UP” marking on top, insert the
bottle into position.
Check that the marking on the bottle is
aligned with the marking on the Toner
bottle Holder.
Pull the seal off the Toner Bottle.
Swing the Toner Bottle Holder closed and
close the Front Door.NOTES
 Use ONLY the specified toner for this machine.
Using any other toner could result in trouble.
 Do not throw away, but keep, the used Toner
Bottle which will be collected by your Tech.
Rep.
 Be careful not to drop the Toner Bottle from a
40 or more height. It may cause damage to the
Toner Bottle.
 When the Front Door is closed, the machine
automatically starts replenishing the supply of
toner. During this period, do not attempt to turn
OFF the Power Switch or open the Front Door.
Toner Replenisher
Use the Toner Replenisher function available
from the Utility Mode if the image is light
immediately after the Toner Bottle has been
replaced with a new one.p. 5-11
5
4002U062AA
6
4002O173AB
7
4002O174AC
Downloaded From ManualsPrinter.com Manuals 
						

							6-8
When a Message Appears
Chapter 6
3. When the Message “Stapler is empty.” Appears
Replacing the Staple Cartridge
Holding the Grip, slide the Finisher away
from the machine.
Open the Front Door.
Slide out the Staple Unit.While pressing down the Staple Cartridge
Lever, pull the Staple Cartridge out its port.
Pull the staple sheet about 1-1/4 inches out of
the new Staple Cartridge and break off that
portion.
Finisher FN-5
The message shown on the left appears when the
staples are running out.
Replace the Staple Cartridge with a new one by
following the procedure given below.
4003P487EA
1
4002O187AA
2
4002O339AA
3
1155O068AA
4
1155O069AA
5
1136O012AA
Downloaded From ManualsPrinter.com Manuals 
						

							6-9
3. When the Message “Stapler is empty.” Appears
When a Message Appears
Chapter 6
NOTE
Check that no portion of the staple sheet hangs
out of the cartridge. Break off any portion of the
sheet that hangs out of the cartridge.
InsertthenewStapleCartridgeuntilaclick
is heard.
Push the Staple Unit back in and close the
Front Door.Slide the Finisher back against the machine.
Touch [Staple] shown on the Touch Panel
and the machine automatically feeds a sheet
of paper to test the stapling.
Remove the sheet of paper to check that it
has been properly stapled.
* If no staples are evident, clear the staple
misfed.
“Clearing the Staple Misfeed.”p. 6-38
NOTES
 Reload the Staple Cartridge only after you are
prompted to do so by the message. Removing
the Staple Cartridge before then will result in
stapling trouble.
 After a new Staple Cartridge has been installed,
be sure to run a test-stapling sequence to
ensure that staples are properly driven into the
paper.
1134O076AA
6
1155O070AA
7
1155O071AA
8
4002O188AC
9
4003P188CA
10
1155O644AC
Downloaded From ManualsPrinter.com Manuals 
						

							6-10
3. When the Message “Stapler is empty.” Appears
When a Message Appears
Chapter 6
Holding the Grip, slide the Finisher away
from the machine.

Open Right Door [FN7].
Turn the dial to the left to move the Staple
Unit (two Stapler Units in FN-105) toward
the center.
Pull the Staple Cartridge out to the front.

NOTE
Two Staple Cartridges are mounted in Finisher
FN-105. Be sure to remove the specific Staple
Cartridge that is indicated in the message on the
To u c h Pa n e l .


Pinch the portions of the Staple Cartridge
marked with “Push” to pop up the upper part
of the cartridge and remove the empty staple
clip.

Remove the empty staple clip from the
Staple Cartridge
.
Finisher FN-105/Finisher FN-106
1
4002O175AC
2
4002O176AB
3
4002O177AB
4
4002O178AAStapler #2 Stapler #1
4002O179AD
Stapler #1
5
4002O362AA
4002O180AB
Downloaded From ManualsPrinter.com Manuals 
						

							6-11
3. When the Message “Stapler is empty.” Appears
When a Message Appears
Chapter 6

Load a new staple clip in the Staple Cartridge
and return the upper part of the cartridge
back again.
Gently peel off the stopper seal.

Load a new staple clip into the Staple
Cartridge and carefully peel off the Seal.
InsertthenewStapleCartridgeuntilaclick
is heard.


Close Right Door [FN7].
Slide the Finisher back against the machine.
Touch [Staple] shown on the Touch Panel
and the machine automatically feeds a sheet
of paper to test the stapling.
Remove the sheet of paper to check that it
has been properly stapled.
* If no staples are evident, clear the staple
misfed.
“Clearing the Staple Misfeed.”
p. 6-40
NOTES
 Reload the Staple Cartridge only after you are
prompted to do so by the message. Removing
the Staple Cartridge before then will result in
stapling trouble.
 After a new Staple Cartridge has been installed,
be sure to run a test-stapling sequence to
ensure that staples are properly driven into the
paper.
6
4002O363AA
4002O181AC
7
4002O182AA
4002O183AD
8
4002O184AB
9
10
4003P188CA
11
4002O186AC
Downloaded From ManualsPrinter.com Manuals 
						

							6-12
3. When the Message “Stapler is empty.” Appears
When a Message Appears
Chapter 6
Press and turn the knob and open the cover at
therearoftheFinisher.
Slide out the Staple Unit.
While pressing down the green lever, pull out
the Staple Cartridge.
Remove the empty staple clip from the
Staple Cartridge.Load a new staple clip into the Staple
Cartridge and carefully peel off the Seal.
Insert the Staple Cartridge into the Staple
Unit until it clicks into place.
Align the arrows and firmly push the Staple
Unit down into the well.
Press and turn the knob to lock the cover.
Mailbin Finisher
1
1155O766AA
2
1166O127AA
3
1166O128AA
4
4002O340AA
5
4002O341AA
6
1166O130AB
7
1166O131AB
8
1155O767AA
Downloaded From ManualsPrinter.com Manuals 
						

							6-13
3. When the Message “Stapler is empty.” Appears
When a Message Appears
Chapter 6
Touch [Staple] shown on the Touch Panel
and the machine automatically feeds a sheet
of paper to test the stapling.
Remove the sheet of paper to check that it
has been properly stapled.
* If no staples are evident, clear the staple
misfed.
“Clearing the Staple Misfeed.”
p. 6-42
NOTES
 Reload the Staple Cartridge only after you are
prompted to do so by the message. Removing
the Staple Cartridge before then will result in
stapling trouble.
 After a new Staple Cartridge has been installed,
be sure to run a test-stapling sequence to
ensure that staples are properly driven into the
paper.
9
4003P188CA
10
1155O736AB
Downloaded From ManualsPrinter.com Manuals