Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Test For Single-Carrier Cabinets Manual

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-9 Access the System 
3
.
Setting the Data Module Operating Mode
1. Connec t an RS-232 c ab le from the DSA/DNA c omp uter to the d ata 
mod ule. If you are using  an 8400B+ , c onnec t the DSA/DNA c omp uter to 
the data module using the supplied adapter cable.
2. Using  a terminal emulator, c onnec t to the serial p ort to whic h...

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-10 Access the System 
3
Setting the 7400B+ Options
1. Set the DIP switc hes for the 7400B+  using  Tab le 3-3. The DIP switc hes are 
loc ated  insid e the unit. To ac c ess them
a. Remove the p ower c ord  from the unit.
b . Remove the c over from the top  rear of the unit.
c . Set the d ip  switc hes.
d . Rep lac e the c over.
e....

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-11 Access the System 
3
Connecting by analog modem to INADS port
You c an c onnec t a PC to the DEFINITY ECS throug h a mod em.
1. Connec t the eq uip ment as shown in Fi g u re  3 - 5
.
Figure 3-5. A typical remote connection through a modem to access a remote 
DEFINITY ECS
Follow these step s to c onnec t to the DEFINITY ECS...

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-12 Access the System 
3
4. Plug  the mod em into an AC p ower outlet.
5. Turn on the modem.
6. Set the following  p ort setting s:
Table 3-4. U.S. Robotics Modem Dip Switch Settings
Dip 
Switch Setting Description
1UP
DOWNData Terminal Ready normal
Data Terminal Ready override
2UP
DOWNVe r b a l  re su lt  c o d e s
Numeric result...

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-13 Activate the System 
3
Activate the System
!CAUTION:
It may b e nec essary to reseat c irc uit p ac ks. To p revent d amag e from static  
elec tric ity, always wear an Elec tromag netic  Comp atib ility (EMC) wrist strap  
(c omc od e 900698226) when hand ling  all system c omp onents.
Install Translation Flash Memory Card
1....

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-14 Activate the System 
3
Figure 3-6. Write Switch on Translation Card
Power Up DC-Powered System
NOTE:
If the system is high or c ritic al reliab ility, p ower-up  the Exp ansion Port 
Network (EPN) first, then the Proc essor Port Network (PPN). 
Always power 
up  the c ontrol c ab inet
 last.
1. At the DC Battery Cab inet (if...

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-15 Activate the System 
3
Verify Messages on Terminal
1. After several minutes, verify all tests p ass. Sc reen 3-1 d isp lays the sc reen 
of a typ ic al Release 8si system.
NOTE:
If any of the terminal messag es ind ic ate a test has failed  or if the 
message spe down mode
 is d isp layed , refer to 
DEFINITY 
Enterprise Communic...

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-16 Screens and Commands 
3
Screens and Commands
Screens
The system is ad ministered  using  sc reens d isp layed  on the terminal. The 
sc reens are used  to ad d , c hang e, d isp lay, list d ata, and  to remove system and  
telep hone features. To ac c ess a sc reen, enter a valid system c ommand in 
resp onse to the command:...

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-17 Administer the System 
3
Administer the System
Contac t the reg ional CSA (Customer Software Assoc iate) to req uest an “ init”  
login. The CSA assig ns the Offer Categ ory op tion. This op tion must b e set b efore 
c ontinuing  with this installation. Limited  c ommand  op tions are availab le until this 
op tion is set. 
Log...

DEFINITY Enterprise Communication Server Release 8.2
Installation and Test for Single-Carrier Cabinets  555-233-120  Issue 1
April 2000
Accessing and Activating the System 
3-18 Administer the System 
3
Change Customer Options
The following features are p art of the b asic  software p ac kag e and  d o not need  to 
b e ac tivated . They d efault to y
 (yes) on the Op tional Features sc reen.
nARS/AAR Partitioning
nEmerg enc y Ac c ess to Attend ant
nHosp itality (Basic )
nService Ob serving
Use the...