Lexmark X264 Service Manual
Have a look at the manual Lexmark X264 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information 4-73 7013-XXX Right side printer cover removal 1.Remove the rear door and cover. See “Rear door and cover removal” on page 4-69. 2.Remove the front scanner cover. See “Front scanner cover removal” on page 4-29. 3.Remove the right side scanner cover. See “Right side scanner cover removal” on page 4-75. 4.Remove the screw (A) from the front of the printer. A
4-74 Service Manual 7013-XXX 5.Press in on the tabs (B), and swing the right side printer cover out. 6.Lift the right side printer cover, and remove. B B
Repair information 4-75 7013-XXX Right side scanner cover removal 1.Lift the ADF scanner cover, and remove the front scanner cover. See “Front scanner cover removal” on page 4-29. 2.Remove the screw (A) from the front of the printer. 3.Remove the screw (B) from the rear of the printer. A B
4-76 Service Manual 7013-XXX 4.Disconnect the right side scanner cover from the printer, and remove.
Repair information 4-77 7013-XXX Toner level sensor removal 1.Open the front access door. 2.Remove the right side printer cover. See “Right side printer cover removal” on page 4-73. 3.Disconnect the toner level sensor cable (A) from J5 on the controller board. 4.Squeeze the lower tabs (B) of the toner level sensor, and push it from its holder. 5.Remove the toner level sensor through the inside of the printer. Note: The toner level sensor must be installed properly, or the printer will not function. BA
4-78 Service Manual 7013-XXX Top printer cover removal 1.Remove the ADF scanner assembly. See “ADF scanner assembly removal” on page 4-9. 2.Open the front access door. 3.Lift the top printer cover, and remove.
Repair information 4-79 7013-XXX Transfer roll removal Note: A flashlight may be useful to remove the transfer roll. 1.Open the front access door. 2.At the right side of the transfer roll, squeeze the holder arms (A) with the left hand while lifting. Stop when the holder is unlatched. 3.At the left side of the transfer roll, squeeze the holder arms with the right hand while lifting with the left hand. Stop when the left holder is unlatched. 4.With a hand at each end, lift the transfer roll out. Note: Do not try removing the spring on the left; it is not removable but can be dislodged. The spring included with the FRU is to be used only if the old right-side spring is damaged or lost. Both springs must be positioned on posts that cannot be seen. If the old springs are moved, then feel the base of the springs to assure that they are on the posts. The top of the springs must be captured in the bearings of the transfer roll.
4-80 Service Manual 7013-XXX Upper front guide assembly removal 1.Open the front access door. 2.Remove the four screws (A) from the upper front guide. 3.Remove the upper front guide. A
Repair information 4-81 7013-XXX Wear strip (tray 1 and 250-sheet tray 2) removal 1.Hold the tray with the bottom up. 2.Use a spring hook to disconnect the strip from the top of the tray. 3.Remove the strip from inside the tray.
4-82 Service Manual 7013-XXX Wear strip (550-sheet tray 2) removal 1.Use a spring hook to disconnect the strip from the top of the tray. 2.Life the strip, and remove. Note: When replacing the strip (for all trays): •Carefully insert the strip from the top of the tray, and push it down through the opening until it clicks into place. •Turn the tray over to view the bottom of the strip. Using the spring hook, check to make sure that the end of the strip is fastened tightly. •Be sure that the drafted edge of the strip is installed toward the bottom of the tray.