Lexmark X264 Service Manual
Have a look at the manual Lexmark X264 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information 4-63 7013-XXX 5.Remove the three screws (B) from the left side of the printer. 6.Disconnect the left hinge (C) from the feed clutch, and remove the e-clip (D). 7.Lift and remove the multipurpose feeder (MPF) feed clutch.
4-64 Service Manual 7013-XXX Nameplate blank cover removal 1.Open the front cover. 2.Remove the three screws (A) from the top of the front cover. 3.Remove the nameplate blank cover. A
Repair information 4-65 7013-XXX Operator panel removal 1.Remove the front scanner cover. See “Front scanner cover removal” on page 4-29. 2.Remove the right side scanner cover. See “Right side scanner cover removal” on page 4-75. 3.Remove the left side scanner cover. See “Left side scanner cover removal” on page 4-35. 4.Remove the screw (A) from the front of the printer. 5.Lift the operator panel, and disconnect the cable (B). 6.Remove the operator panel. 7.Remove the bezel from the operator panel. A B
4-66 Service Manual 7013-XXX Operator panel cable removal 1.Remove the ADF scanner assembly. See “ADF scanner assembly removal” on page 4-9. 2.Disconnect the operator panel cable from J14 on the controller board. 3.Un-route the operator panel cable from the scanner tub frame assembly. 4.Remove the operator panel cable.
Repair information 4-67 7013-XXX Paper input and duplex sensor assembly removal 1.Remove the right side printer cover. See “Right side printer cover removal” on page 4-73. 2.Remove the duplex. See “Duplex removal” on page 4-16. 3.Remove the two screws (A) from the sensors. 4.Disconnect the sensor cable (B) from J30 on the controller board. 5.Remove the paper input and duplex sensor assembly. A B
4-68 Service Manual 7013-XXX Printhead removal 1.Remove the top cover. See “Top printer cover removal” on page 4-78. 2.Remove the right side printer cover. See “Right side printer cover removal” on page 4-73. 3.Disconnect the two cables (A) from J12 and J8 on the controller board, and unroute them back through the frame toward the printhead. 4.Remove the three screws (B). Note: Use a pencil to mark the screw locations of the printhead on the metal frame. Align the new printhead relative to the location of the old printhead. See “Printhead assembly mechanical adjustment” on page 3-24. 5.Remove the printhead. A B
Repair information 4-69 7013-XXX Rear door and cover removal 1.Open the rear door. 2.Pull the rear door up at an angle, disconnect the door from the notch (A), and remove. 3.Remove the two screws (B) from the top of the rear cover. A B
4-70 Service Manual 7013-XXX 4.Tilt the rear cover, and lift to remove.
Repair information 4-71 7013-XXX Rear exit guide assembly with sensor and reversing solenoid removal 1.Remove the top printer cover. See “Top printer cover removal” on page 4-78. 2.Remove the rear door and cover. See “Rear door and cover removal” on page 4-69. 3.Disconnect the narrow media sensor cable and the reversing solenoid cable (A) from J9 and J10 on the controller board. 4.Remove the six screws (B) from the rear exit guide assembly. BBB
4-72 Service Manual 7013-XXX 5.Remove the solenoid cable (C) through the opening. 6.Remove the narrow media sensor cable (D) through the opening. 7.Remove the rear exit guide assembly. Note: Be careful to not damage the gears during the rear exit guide assembly removal and reinstallation.