Lexmark X264 Service Manual
Have a look at the manual Lexmark X264 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information 4-53 7013-XXX Installation notes: 1.Remove the new clutch from its packaging. 2.Measure 4 inches (100 mm) from the clutch, and cut the clutch cable. 3.Install the new media clutch on the ACM drive shaft. 4.Insert the red wire from the printer into the wire splice connector. 5.Insert the red wire from the clutch into the wire splice connector.
4-54 Service Manual 7013-XXX 6.Using a pair of pliers, squeeze the connector to secure the red wires in place. Note: Check the connector to make sure that the gray connector is pressed flush to the bottom of the wire splice. 7.Repeat steps four through six for the black wires on the clutch and printer. 8.Tuck the connectors securely above the duplex guide. Note: If needed, use a wire tie to secure the cable in place. Make sure the tie does not interfere with the paper path. 9.Reinstall the gear drive. 10.Print the menu pages to test the printer. 11.Reinstall the left cover.
Repair information 4-55 7013-XXX Media manual input sensor removal 1.Remove the right side printer cover. See “Right side printer cover removal” on page 4-73. 2.Place the machine on its side. Note: Be careful to not mar the finish of the printer. 3.Disconnect the sensor cable (A) from J26 (MPFS) on the controller board. 4.Remove the screw (B). 5.Free the cable from its retainers, and pull it through the opening toward the sensor mount. A B
4-56 Service Manual 7013-XXX Reinstallation note: •Prop open the duplex door, and insert the hook end of the spring hook through the frame opening (C) from the controller board side. Extend the hook until the sensor connector can be hooked. •Hook the spring hook (D) to the connector (E), and pull it through the opening. •Place the sensor into position, and reconnect the cable on the controller board. •Using the spring hook, be sure to reroute the cable through the three retainers (F) between the sensor and side frame. Note: If the cable is not properly installed in its retainers, then the loose cable will obstruct the paper path. EDC F
Repair information 4-57 7013-XXX Warning: Check to make sure the duplex paper jam door is in its proper position. If it is not, then the paper tray will become lodged and the printer will need to be replaced.
4-58 Service Manual 7013-XXX Multipurpose feeder (MPF) removal 1.Open the front access door. 2.Remove the four screws (A) from the upper front guide. 3.Remove the upper front guide. 4.Remove the two screws (B). A B
Repair information 4-59 7013-XXX 5.Close the front access door, and pull up on the MPF by the steel shaft until the MPF lifts from its hinges. Note: The picture below shows the E460dn, E460dw printer. The multipurpose feeder removal is the same for all MFP models. 6.Disconnect the MPF from the lower front cover.
4-60 Service Manual 7013-XXX 7.Open the front access door, and remove the lower paper guide.
Repair information 4-61 7013-XXX MPF tray removal 1.Open the lower front cover. 2.Remove the four screws (A). 3.Disconnect the MPF tray, and remove. A
4-62 Service Manual 7013-XXX Multipurpose feeder (MPF) feed clutch removal 1.Remove the left side printer cover. See “Left side printer cover removal” on page 4-33. 2.Remove the duplex. See “Duplex removal” on page 4-16. 3.Disconnect the cable (A) from J29 on the controller board. 4.Place the printer on its right side. Note: Be careful to not damage any cables or mar the finish of the printer.