Lexmark X264 Service Manual
Have a look at the manual Lexmark X264 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information 4-43 7013-XXX 5.Lift the gear drive, and disconnect the main motor gear drive cable (C). 6.Remove the main motor gear drive.
4-44 Service Manual 7013-XXX Manual feed clutch removal 1.Remove the left side printer cover. See “Left side printer cover removal” on page 4-33. 2.Open the front access door, and disconnect the fuser link (A). 3.Place the printer on its right side. Note: Be careful to not mar the finish of the printer. 4.Remove the four screws (B) from the main motor gear drive. 5.Rotate the main motor gear drive enough to access the manual feed solenoid. A B
Repair information 4-45 7013-XXX 6.Use a screwdriver to remove the e-clip (C) from the manual feed clutch. Note: The picture below shows the E260d, E260dn printer. The manual feed clutch removal is the same for the MFP models. 7.Remove the manual feed clutch (D). C D
4-46 Service Manual 7013-XXX Manual feed solenoid removal 1.Remove the right side printer cover. See “Right side printer cover removal” on page 4-73. 2.Remove the duplex. See “Duplex removal” on page 4-16. 3.Open the front access door, and place the printer on its right side. Note: Be careful to not mar the finish of the printer. 4.Remove the two screws (A). 5.Remove the three screws (B) from the left door mount. A B
Repair information 4-47 7013-XXX 6.Lift the left door mount (C) away from the side frame, and unroute the cable (D) with a spring hook. 7.Reinstall the left door mount, and place the printer on its top. Note: Be careful to not mar the finish of the printer. 8.Disconnect the cable (D) from J25 on the controller board, and remove the manual feed solenoid. Installation note: Install the two screws holding the new solenoid in place, and route the cable (D) behind the MPF clutch (E). ECD
4-48 Service Manual 7013-XXX Media ACM ASM feeder removal 1.Remove the left side printer cover. See “Left side printer cover removal” on page 4-33. 2.Remove the LVPS/HVPS. See “LVPS/HVPS removal” on page 4-39. 3.Remove the duplex. See “Duplex removal” on page 4-16. 4.Remove the main motor gear drive. See “Main motor gear drive removal” on page 4-42. 5.Loosen the media feed clutch. See “Media feed clutch removal” on page 4-51. Warning: Do not cut the media feed clutch cable (leave the media feed clutch hanging). 6.Use a screwdriver to pop the shaft retainer tab (A) loose from the ACM feed shaft. 7.Use a small pair of pliers to remove the shaft retainer tab.
Repair information 4-49 7013-XXX 8.Use a screwdriver to pop the inner shaft lock (B) loose. 9.Remove the inner shaft lock (C).
4-50 Service Manual 7013-XXX 10.Pull out the auto compensator shaft, and remove the spring (D). 11.Remove the auto compensator shaft. 12.Disconnect the spring (E) from the cylinder. 13.Remove the media ACM ASM feeder. E
Repair information 4-51 7013-XXX Media feed clutch removal 1.Remove theleft cover. See “Left side printer cover removal” on page 4-33. 2.Remove the main motor gear drive. See “Main motor gear drive removal” on page 4-42. 3.Carefully remove the e-clipthat secures the clutch to the ACM shaft. 4.Pull up the clutch from the cavity, exposingthe white tape. 5.Cut the tape to expose the wire connectionto the clutch, and cut the cables at the copper leads. 6.Clean any adhesive residue from the wires.
4-52 Service Manual 7013-XXX 7.Pull the clutch cable into the motor cavity. Pull up the cable to remove any slack. 8.Remove any shrink tubing that is holding the wires together. Warning: Do not strip the insulation off the red and black wires. The connectors will not work if the insulation is removed.