Lexmark X264 Service Manual
Have a look at the manual Lexmark X264 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information 4-23 7013-XXX Fax card removal 1.Remove the rear door and cover. See “Rear door and cover removal” on page 4-69. 2.Remove the right side printer cover. See “Right side printer cover removal” on page 4-73. 3.Remove the two screws (A) securing the fax card to the printer frame. 4.Disconnect the cable (B) from the controller board. 5.Remove the fax card. CAUTION This product contains a lithium battery. THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED BY AN INCORRECT TYPE. Discard used batteries according to the battery manufacturer’s instructions and local regulations.
4-24 Service Manual 7013-XXX Flatbed removal 1.Remove the ADF. See “ADF removal” on page 4-4 or “Toner level sensor removal” on page 4-77. 2.Remove the left side scanner cover. See “Left side scanner cover removal” on page 4-35. 3.Remove the right side scanner cover. See “Right side scanner cover removal” on page 4-75. 4.Remove the right side printer cover. See “Right side printer cover removal” on page 4-73. 5.Remove the operator panel. See “Operator panel removal” on page 4-65. 6.Remove the two screws (A) from the rear of the tub. 7.Remove the two screws (B) from behind the operator panel. 8.Disconnect the ribbon cable from J12, the flatbed motor cable from JFBM1, and the home sensor cable from J1 on the controller board. A B
Repair information 4-25 7013-XXX 9.Remove the torroid (C) from the ribbon cable. 10.Lift the scanner, and remove all cables. 11.Remove the scanner.
4-26 Service Manual 7013-XXX Installation note: 1.Remove the clear plastic guide from the old flatbed and attach it to the new flatbed. 2.Route the CCD ribbon cable through the guide as shown below. 3.Install the large torroid from the old ribbon cable onto the CCD ribbon cable as shown above. 4.Route the flatbed motor cable and the home sensor cables in the channel and under the tab (D).
Repair information 4-27 7013-XXX 5.Route the flatbed motor cable and the home sensor cables under the ribbon cable folding guide (E) and torroid (F). 6.After the cables are folded and routed, the flatbed assembly should look like the picture below.
4-28 Service Manual 7013-XXX Front door access cover blank removal 1.Remove the nameplate blank cover. See “Nameplate blank cover removal” on page 4-64. 2.Remove the two screws (A). 3.Remove the front door access cover blank. A
Repair information 4-29 7013-XXX Front scanner cover removal 1.Use a flathead screwdriver to pry the front scanner cover away from the printer. Note: Be careful to not mar the finish of the printer. 2.Pull the scanner cover away from the operator panel. 3.Remove the front scanner cover.
4-30 Service Manual 7013-XXX Fuser removal 1.Remove the rear exit guide. See “Rear exit guide assembly with sensor and reversing solenoid removal” on page 4-71. 2.Remove the two screws (A). 3.Partially pull the fuser forward for better access.
Repair information 4-31 7013-XXX 4.Push in on the cable connector cover (B), and remove. 5.Disconnect the AC cable (C). 6.Disconnect the thermistor cable (D). C B D
4-32 Service Manual 7013-XXX 7.Disconnect the exit sensor cable (E) from the controller board. 8.Remove the fuser. Note: •Be careful to not damage the gears during the fuser installation. •Be sure to reinstall the AC cable during the fuser installation. E