Kyocera TASKalfa 221 User Manual

							Copier Functions1-13
Border Erase Mode
Shadows that may appear around the edges of copies can be erased.
The following modes are availabl e for border erase function.
NoteYou can set the default value of the border erase width. (See  Border Erase Width Default Value 
on page 3-10.)
1Set the original.
2Press the  Border Erase  key.
3Press the S key or the T  key to select Sheet Erase  
or  Book Erase.
4Press the  Enter key.
5Press the  < key or the  > key to set the border erase 
width. You can set the width to  1/8 to 3/4 in 1/8 
increments [1 mm to 18 mm in 1 mm increments].
6Press the  Enter key.
7Press the  Start key. Copying starts.
Mode
Description
Sheet Erase Use this mode to erase shadows t hat may appear around the edges of 
copies made from sheet originals.  You can set the width of the border 
to be erased to 1/8 to 3/4 in 1/8 increments [1 mm to 18 mm in 1 mm 
increments].
Book Erase Use this mode to make clean copies from a thick book. You can set the 
width of the border to be erased to 1/8 to 3/4 in 1/8 increments 
[1 mm to 18 mm in 1 mm increments].
Border Erase :
Sheet Erase
Book Erase
Border Erase Width :
1/ 81/4  3/4
Downloaded From ManualsPrinter.com Manuals 
						

							Copier Functions
1-14
Continuous Copying
The continuous copying function allows multiple originals to be separated into some blocks, to be 
scanned at more than one time, and to be copied in one batch. Since multiple originals of the same 
type are scanned in multiple steps to accumulate data in memory, many originals can be copied in 
one batch.
1Set the originals.
2Press the  Function key.
3Press the  S key or the  T key to select  Continuous 
scan .
4Press the  Enter key.
5Press the  S key or the  T key to select  On.
6Press the  Enter key.
7Press the  S key or the  T key to select  End.
8Press the  Enter key.
9Press the  Start key. Scanning of originals starts.
10Replace the originals and press the  Start key. Scanning of originals of the next step starts.
11When all originals have been scanned, press the  Enter key. Copying starts.
Continuous Scan
Function :
End
Orig. Orient .:
:Top Edge
Off
Continuous Scan :
Off
On*
Downloaded From ManualsPrinter.com Manuals 
						

							Copier Functions1-15
Auto Rotation
With the auto rotation function, t he image of the original is automatically rotated counterclockwise by 
90 degrees if the orientation of the original is diff erent from that of the paper loaded in the cassette.
Notes• The paper sizes that can be used for auto rotation are A4/11 × 81/2 or smaller sizes. A3, B4, 
Folio, 11 × 17 (Ledger), 8
1/2× 14 (Legal) or 8K cannot be used for auto rotation.
• You can select whether or not to enable auto rotation at a default setting. (See  Auto Rotation 
Copy  on page 3-9.)
1Set the original.
2Press the  Function key.
3Press the  S key or the  T key to select Auto 
Rotation.
4Press the  Enter key.
5Press the  S key or the  T key to select On or  Off.
6Press the  Enter key.
Auto Rotation
Function :
Orig. Orient .
Continuous Scan
:
:Top Edge
Off
:On
Auto Rotation : Off
On*
Downloaded From ManualsPrinter.com Manuals 
						

							Copier Functions
1-16
EcoPrint Mode
The ecoprint mode can reduce toner consumption. Use this mode when high quality copies are not 
necessary, for example, for trial copying.
Notes• The copy densityDensity will be a little lighter.
• You can select whether or not to turn on  the ecoprint mode at a default setting. (See EcoPrint 
Mode  on page 3-4.)
1Set the original.
2Press the  Function key.
3Press the  S key or the  T key to select  EcoPrint.
4Press the Enter key.
5Press the  S key or the  T key to select  On or  Off .
6Press the  Enter key.
EcoPr int
Function :
Continuous Scan
Auto Rotation
:
Off
OnOff
: :
EcoPrint :
Off
On*
Downloaded From ManualsPrinter.com Manuals 
						

							Copier Functions
1-17
Mixed Size Originals Mode
With  Mixed Size Originals, you  need not use the Paper Selection key to specify the paper size 
when  using  the opti onal document  processor. T he origi nal sizes  are detected  one by one and ea ch 
origi nal is automatical ly copied to a sheet of the same size.
Notes•The maximum numb er of sheets that can be set in  the do cument  processor in  this mode  is 30.
• The origin al sizes th at can be  used for the auto se lection mode:
Inch Specification  — 11 × 8
1/2 and 1 1×17 (L edger) or 81/2×14  (Legal) and 81/2× 11 
(Letter)
Me tric S pecification  — A3 and A4, f olio and A4R, or B4 and B5. 
The  origin al width  must be the  same.
1Set the orig inals in the docum ent processor.
2Press the Mixed Size Originals  key.
3Press  the Start  key. C opying st arts.
Downloaded From ManualsPrinter.com Manuals 
						

							Copier Functions
1-18
Program Function
Up to eight combinations of copy modes and functions displayed on the operation panel can be 
registered as a single program.
Registering a Program
1Set the desired copy modes, etc., to be registered.
2Press the  Program key.
3Press the  S key or the  T key to select  Register 
program .
4Press the  Enter key.
5Press the  S key or the  T key to select the program 
number to register (1 to 8).
NoteYou can also select the program number using a numeric key.
6Press the  Enter key. The program is registered.
Using a Program to Make Copies
1Press the  Program key.
2Press the  S key or the  T key to select the program 
number to recall.
NoteYou can also select the program number using a numeric key.
3Press the  Enter key.
4Set the originals and press the  Start key. Copying starts with the settings that were registered.
Register program .
Program :
Program #7
Program #8
Program #3
Register program :
Program #1
Program #2
Program #3
Program :
Program #1
Program #2
Downloaded From ManualsPrinter.com Manuals 
						

							2-1
2 Printer Settings
This chapter explains the settings required for using the printer functions. For setting operation 
required for using this machine as a network printer, use the operation panel.
The principal settings that can be made are shown below.
• Using This Machine as a Network Printer
• Menu Hierarchical Diagram
• Status Page Printing
• e-MPS Function
• Interface
•Emulation
• Font
• Print Configuration
• Print Quality
• Memory Card Operation
• Hard Disk Operation
• RAM Disk Operation
• Paper Handling
• Other Settings
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings
2-2
Using This Machine as a Network Printer
To use this machine as a network printer, use the procedure below for the setting.Preparation of network connection environment(Assignment of IP address, etc.)
È
Connection of network cable
(Refer to the  Basic Operation Guide , Connecting the Network Cable.)
È
Setting operation from the operation pane l of this machine (See this chapter.)
Principal setting items
•Network
• Emulation selection
• Number of copies and print orientation
• Print quality
• Paper sizes for the cassette and multi-purpose tray È
Installation and setting operation of printer driver
(Refer to the  KX Printer Driver Operation Guide .)
È
Printing from application
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings2-3
Menu Hierarchical Diagram
Note> displayed on each setting screen indicates the current setting.
Print Status 
Page `No
, Print
e-MPS `Quick Copy `Select User 
Name`Select JOB
`Copies: ###
Delete
Private/
Stored `Select User 
Name`Select JOB
`Copies: ### Enter User ID
Delete
Print VMB 
Data `Tray ### Enter User ID
List of VMB `No,  Print
List of code 
JOB `No, 
Print
e-MPS 
Configuration `Quick Copy
`Number of JOB:  0 to  50
Temp Code Job 
Size `0
 to  9999 M Byte
Perm Code Job 
Size `0
 to  9999 M Byte
VMB Size `0 to  9999 M Byte
Interface `Network `NetWare `On, Off
Change # `Auto,  802.3,  Ethernet II , 
802.2,  802.3 SNAP
TCP/IP `On, Off
Change # `DHCP `On, Off
IP Address `### .###. ###.###
Subnet Mask `### .###. ###.###
Gateway `### .###. ###.###
EtherTalk `On, Off
Network 
Status Page `On
, Off
USB
O ption `NetWare `On, Off
C

hange # `Auto,  802.3,  Ethernet II , 
802.2,  802.3 SNAP
TCP/IP `On, Off
Change # `DHCP `On, Off
IP Address `### .###. ###.###
Subnet Mask `### .###. ###.###
Gateway `### .###. ###.###
EtherTalk `On, Off
Opt. 
StatusPage `On
, Off
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings
2-4
Emulation`PCL 6
KC-GL `KC-GL Pen 
Adjust `Pen (1
 to 8) `01 to  99 dot(s)
KC-GL Page 
Set `A2, A1, 
A0, B3,  B2, B1,  B0, SPSZ
KPDL `Print KPDL 
Errs `On, Off
KPDL (AUTO) `Print KPDL 
Errs `On, Off
Alt. 
Emulation `PCL6
, KC-GL , Line Printer , IBM Proprinter , 
Diablo 630 , EPSON LQ-850
Line Printer
IBM Proprinter
Diablo 630
EPSON LQ-850
Font `Select Font `Internal `I### ID `I###
Detail `4 to  999.75 Point
0.44 to  99.99 CPI
Courier `Dark,  Regular
Letter 
Gothic `Dark, 
Regular
Option `#### ID `S###,  M###, H### , O###
Detail `4 to  999.75 Point
0.44 to  99.99 CPI
Code Set `#####
List of 
Inter. Fonts `No, 
Print
List of 
Option Fonts `No, 
Print
Page S et
`Copies `1 to  999
Zoom(Reduce) `Paper size  ###

,  Print size ###
Orientation `Portrait , Landscape
Page Protect `Auto,  On
LF Action `LF only , CR and LF , Ignore LF
CR Action `CR only , CR and LF , Ignore CR
Wide A4 `On,  Off
Print 
Quality `KIR Mode
`On,  Off
Ecoprint 
Mode `On, 
Off
Resolution `Fast1200 Mode , 600 dpi, 300 dpi
Print 
Density `1
 to  5
Downloaded From ManualsPrinter.com Manuals