Konica Minolta magicolor 1690MF d User Manual

							Cleaning the Machine 8-4
Cleaning the Machine
CAUTION
Be sure to turn off the machine and unplug the power cord before 
cleaning. However, be sure to turn on the machine when cleaning the 
print head window.
Exterior
M
„Control Panel
„Machine Exterior
„Original Cover Pad „Original Glass„Ventilation Grill
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Machine8-5 Media Rollers
The accumulation of paper dust and other debris on the media rollers can 
cause media-feeding problems. 
Cleaning the Media Feed Roller
1Open the scanner unit.
If there is paper in the 
output tray, remove it, 
and then fold up the out-
put tray before opening 
the scanner unit.
Note
Do not touch the wires and flat 
cable shown in the illustration.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Machine 8-6
2Grab the handle and lift it up 
slightly to the back, and then 
slowly pull the imaging cartridge 
out vertically.
Note
Do not touch the PC drum and the transfer belt on the imaging 
cartridge. 
Position the removed imaging 
cartridge horizontally as shown in 
the illustration at the right.
Be sure to keep the imaging 
cartridge horizontal and place it 
where it will not become dirty.
Do not leave the imaging 
cartridge removed for more than 
15 minutes, and do not place the 
removed imaging cartridge in a 
location where it would be 
exposed to direct light (such as 
sunlight).
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Machine8-7
3Clean the media feed rollers by 
wiping them with a soft, dry 
cloth.
CAUTION
The area around the fuser unit is 
extremely hot.
Touching anything other than the 
indicated levers may result in 
burns. If you get burned, 
immediately cool the skin under 
cold water, and then seek 
professional medical attention.
BOTTOM
VIEW
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Machine 8-8
Note
Decreased print quality may 
result if the surface of the 
transfer roller is touched.
Be careful not to touch the 
surface of the transfer roller. 
4Slowly insert the imaging car-
tridge vertically, and then push it 
slightly down toward you to fin-
ish reinstalling the imaging car-
tridge.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Machine8-9
5Carefully close the scanner unit.
Note
Do not touch the wires and flat 
cable shown in the illustration.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Machine 8-10
Cleaning the Media Feed Rollers for the ADF
1Open the ADF feed cover.
2Clean the media feed rollers by 
wiping them with a soft, dry 
cloth.
3Close the ADF feed cover.
M
M
M
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Machine8-11
Cleaning the Media Feed Rollers for Tray 2
Be sure to remove the duplex option before cleaning the media feed rollers 
for Tray 2.
1If the duplex option is installed, remove it.
If the duplex option is not installed and the locking pins are 
installed at the back of Tray 2, remove the locking pins (one in 
each opening on the left and right sides at the back of Tray 2).
To remove a locking pin, turn it to either the left or the right so that 
its grip is vertical, and then pull out the locking pin to remove it.
2Remove the dust cover from Tray 1 and close the tray.
3Lift the machine off of Tray 2 and 
temporarily place it on a sturdy 
flat surface.
4Clean the media feed rollers by 
wiping them with a soft, dry 
cloth.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Machine 8-12
5Lift the machine and reinstall it 
on top of Tray 2.
6Open Tray 1 and reattach the dust cover.
7If you removed the duplex option in step 1, reinstall it.
If the duplex option is not to be installed, install the locking pins.
While holding the grip of the locking pin vertical, insert the locking 
pin into the opening on either the left or right side of the lower 
feeder unit and, while pushing it in, turn it to either the left or the 
right. The locking pin is installed when its grip is horizontal.
Installing the left and right locking pins secures the lower feeder 
unit to the machine so it cannot be removed.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Machine8-13
Cleaning the Media Feed Rollers for the attachment
Be sure to remove the duplex option before cleaning the media feed rollers 
for the attachment.
1If the duplex option is installed, remove it.
2Remove the dust cover from Tray 1 and close the tray.
3Lift the machine off of the attach-
ment and temporarily place it on 
a sturdy flat surface.
4Clean the media feed rollers by 
wiping them with a soft, dry 
cloth.
Downloaded From ManualsPrinter.com Manuals