Konica Minolta magicolor 1690MF d User Manual

							Scanning With the Machine 6-8
Scanning With the Machine
The machine keys can be used to make scans. This operation differs from 
scanning from a computer application since the destination of the scan data 
can also be specified.
Before scanning, check that the Scan key is lit up in green. If the key 
is not lit up in green, press the Scan key to enter Scan mode.
If, while specifying settings, no key is pressed for the length of time 
specified for 
AUTO PANEL RESET, the entered settings are can-
celed and the main screen (Scan mode) is displayed.
Scanning with the original glass is possible only with A4-, A5-, B5 
(JIS)-, Letter- or Statement-size documents.
Scanning with the ADF is possible only with A4-, A5-, B5 (JIS)-, 
Legal-, Letter- or Statement-size documents.
Basic Scanning Operation
1Position the document to be 
scanned. 
For details on positioning 
the document, refer to 
“Placing a document on 
the original glass” on 
page 3-28 and “Loading 
a document into the ADF” 
on page 3-29.
Downloaded From ManualsPrinter.com Manuals 
						

							Scanning With the Machine6-9
2Press the Scan key to enter Scan mode.
3Specify the desired scan settings.
For details on specifying the destination of the data, refer to “Spec-
ifying the Data Location” on page6-10 and “Specifying the Desti-
nation Address (Scan to E-mail/FTP/SMB)” on page 6-12.
For details on selecting the data format, refer to “Selecting the 
Data Format” on page 6-26.
For details on selecting the scan quality setting, refer to “Selecting 
the Scan Quality Setting” on page 6-27.
For details on setting the scan size, refer to “Setting the Scan Size” 
on page 6-28.
For details on setting the color of the scan data, refer to “Setting 
the Scan Color” on page 6-28.
For details on specifying the subject when sending data, refer to 
“Specifying the Subject” on page 6-28.
4To scan color scans, press the Start-Color key. To scan monochrome 
scans, press the Start-B&W key.
If the document was loaded in the ADF, scanning begins, and then the 
data is sent to the specified location. If the document was placed on the 
original glass, continue with step 5.
Scanning with the Scan to PC operation is possible only if this 
machine is connected to a computer using a USB cable.
5When NEXT PAGE? appears in the message window, place the second 
document page on the original glass, and then press the Select key.
When scanning with the Scan to PC operation, a multi-page docu-
ment cannot be scanned with the original glass. To scan a 
multi-page document, load the document into the ADF.
6Press the + or , key to select the size of the document positioned in step 
5, and then press the Select key.
7After all document pages have been scanned, press the Start key.
The scanned document is sent to the specified location.
If the Stop/Reset key is pressed while scanning, JOB CANCEL 
appears. To continue scanning, select 
NO. To stop scanning, 
select 
YES.
To cancel a job where scanning was finished and the data is 
queued to be sent, refer to “Deleting a Queued Transmission Job” 
on page 6-29.
Downloaded From ManualsPrinter.com Manuals 
						

							Scanning With the Machine 6-10
Specifying the Data Location
Select whether the computer or USB memory device is the location where 
scan data is to be saved. When transmitting via a network, refer to “Specify-
ing the Destination Address (Scan to E-mail/FTP/SMB)” on page 6-12.
If an address has been specified as the destination for the data, SCAN 
TO PC
 and SCAN TO USB MEMORY cannot be selected.
Saving Data on a Computer Connected (Scan to PC)
In order to perform Scan to PC operations, the following requirements must 
be met.
zThis machine is connected to a computer using a USB cable.
zThe TWAIN scanner driver, the printer driver and LinkMagic (Windows 
only) are installed on the computer.
zEither LinkMagic is activated or the LinkMagic icon appears in the 
Windows notification area.
zThe document is positioned at the location specified with Paper 
Source (Flatbed (original glass) or ADF) in LinkMagic.
For details on LinkMagic, refer to the Reference Guide on the Docu-
mentation CD/DVD.
Follow the procedure described below to send scan data to a computer con-
nected to this machine.
The scan settings specified with LinkMagic are given priority. Specify 
the various settings with LinkMagic. For details, refer to the Reference 
Guide on the Documentation CD/DVD.
1In the main screen (Scan mode), press the + or , key to select SCAN 
TO
, and then press the Select key.
2Press the + or , key to select SCAN TO PC, and then press the Select 
key.
The scan data is saved in the folder specified with LinkMagic. For 
details, refer to the Reference Guide on the Documentation CD/DVD.
Downloaded From ManualsPrinter.com Manuals 
						

							Scanning With the Machine6-11
Saving Data on a USB Memory Device (Scan to USB 
Memory)
Follow the procedure described below to save scan data to a USB memory 
device plugged into the USB memory port of this machine.
This machine is compatible with a USB Host device of 4 GB or less.
1Plug the USB memory device into the USB Host port of this machine.
2In the main screen (Scan mode), press the + or , key to select “SCAN 
TO”, and then press the Select key.
3Press the + or , key to select SCAN TO USB MEMORY, and then press 
the Select key.
Depending on the USB memory device that is used, it may take some 
time for the scan data to be transferred.
Downloaded From ManualsPrinter.com Manuals 
						

							Scanning With the Machine 6-12
Specifying the Destination Address (Scan to E-mail/FTP/
SMB)
Scan data can be sent via the network to a specified address (e-mail address, 
FTP address or SMB address). The address can be typed in directly, or an 
address registered on the machine can be selected.
To send scan data via the network, settings for NETWORK SETTING 
and 
E-MAIL SETTING (when sending to an e-mail address) must 
be specified.
If the size of the scan data sent by e-mail exceeds the size specified 
with 
FILE SIZE, the data is automatically divided into multiple 
e-mail messages. For details, refer to “SCAN SETTING Menu” on 
page 2-52.
To save scan data in a shared folder on a computer installed with 
Windows or on the FTP server, the FTP address or SMB address 
must be registered as a speed dial destination. These addresses can 
be registered only from Local Setup Utility (LSU) or PageScope Web 
Connection. For details, refer to the Reference Guide on the Docu-
mentation CD/DVD.
Directly Entering the E-mail Address
The destination address (e-mail address) where the scan data is to be sent 
can be directly typed in.
A maximum of 16 addresses (total of e-mail addresses from direct 
input and an LDAP search) can be specified.
1In the main screen (Scan mode), use the keypad to type in the destination 
address (up to 64 characters).
For details on entering/editing text, refer to “Entering Text” on 
page A-6.
2After the text is entered, press the Select key.
3If an e-mail address was selected, press the + or , key to select FIN-
ISH
, and then press the Select key.
To add an additional e-mail address, select ADD in step 3, and 
then specify the destination.
To edit the specified e-mail address, select 
CHECK/EDIT in step 
3, and then continue with step 2 of “Editing a Specified Destination 
Address”. To delete an address, select 
CHECK/EDIT in step 3, 
and then continue with step 2 of “Deleting a Specified Destination 
Address”.
Downloaded From ManualsPrinter.com Manuals 
						

							Scanning With the Machine6-13
Selecting From the Favorite List
From the speed dial destinations and group dial destinations registered on 
this machine, register a maximum of 20 destinations in the favorite list for 
convenient access to frequently specified destinations. Follow the procedure 
described below to specify an address (e-mail address, FTP address or SMB 
address) from the favorite list as the recipient of the scan data.
For details on registering addresses in the favorite list, refer to “Regis-
tering in the Favorite List” on page 6-20.
1With the main screen (Scan mode) or Can Use AddressBook dis-
played, press the AddressBook key so that 
FAVORITE appears.
2Press the + or , key to select the desired data, and then press the Select 
key.
3Press the Select key again.
If an FTP address or an SMB address was selected, the destination 
address is specified.
4If an e-mail address was selected, press the + or , key to select FIN-
ISH
, and then press the Select key.
To add an additional e-mail address, select ADD in step 4, and 
then specify the destination. When sending the data to an FTP 
address or SMB address, multiple addresses cannot be specified.
To check the specified e-mail address, select 
CHECK/EDIT in 
step 4. To delete an address, select 
CHECK/EDIT in step 4, and 
then continue with step 2 of “Deleting a Specified Destination 
Address”.
Selecting a Speed Dial Destination
A maximum of 250 speed dial destinations can be registered on this machine. 
Follow the procedure described below to specify an address (e-mail address, 
FTP address or SMB address) from the registered speed dial destinations as 
the recipient of the scan data.
For details on registering addresses as speed dial destinations, refer 
to “Registering Speed Dial Destinations (Direct Input)” on page 6-21 
or “Registering Speed Dial Destinations (LDAP Search)” on 
page 6-22.
1With the main screen (Scan mode) or Can Use AddressBook dis-
played, press the AddressBook key twice so that 
SPEED DIAL 
appears.
2Use the keypad to type in the number (between 1 and 250) for the speed 
dial destination, and then press the Select key.
Downloaded From ManualsPrinter.com Manuals 
						

							Scanning With the Machine 6-14
The information registered for the speed dial destination appears for two 
seconds.
3Press the Select key again.
If an FTP address or an SMB address was selected, the destination 
address is specified.
4If an e-mail address was selected, press the + or , key to select FIN-
ISH
, and then press the Select key.
To add an additional e-mail address, select ADD in step 4, and 
then specify the destination. When sending the data to an FTP 
address or SMB address, multiple addresses cannot be specified.
To check the specified e-mail address, select 
CHECK/EDIT in 
step 4. To delete an address, select 
CHECK/EDIT in step 4, and 
then continue with step 2 of “Deleting a Specified Destination 
Address”.
Selecting a Group Dial Destination
A maximum of 20 group dial destinations can be registered on this machine. 
(A maximum of 50 e-mail addresses can be registered with one group.) Fol-
low the procedure described below to specify e-mail addresses from the reg-
istered group dial destinations as the recipient of the scan data.
For details on registering e-mail addresses as group dial destinations, 
refer to “Registering Group Dial Destinations” on page 6-24.
A group dial destination containing a telephone number cannot be 
used in Scan mode.
1With the main screen (Scan mode) or Can Use AddressBook dis-
played, press the AddressBook key three times so that 
GROUP DIAL 
appears.
2Use the keypad to type in the number (between 1 and 20) for the group 
dial destination, and then press the Select key.
The information registered for the group dial destination appears for two 
seconds.
3Press the Select key again.
4Press the + or , key to select FINISH, and then press the Select key.
To add an additional e-mail address, select ADD in step 4, and 
then specify the destination.
To check the specified e-mail address, select 
CHECK/EDIT in 
step 4. To delete an address, select 
CHECK/EDIT in step 4, and 
then continue with step 2 of “Deleting a Specified Destination 
Address”.
Downloaded From ManualsPrinter.com Manuals 
						

							Scanning With the Machine6-15
Selecting From the Address Book
The speed dial destinations and group dial destinations registered on this 
machine are saved in the address book. Follow the procedure described 
below to specify an address (e-mail address, FTP address or SMB address) 
from the address book as the recipient of the scan data.
This feature is available only if data has been registered in the 
address book.
1With the main screen or Can Use AddressBook displayed, press the 
AddressBook key four times so that 
PHONE BOOK appears.
2Press the + or , key to select LIST, and then press the Select key.
A list of the address book contents appears.
3Press the + or , key to select the desired data, and then press the Select 
key.
4Press the Select key again.
If an FTP address or an SMB address was selected, the destination 
address is specified.
5If an e-mail address was selected, press the + or , key to select FIN-
ISH
, and then press the Select key.
To add an additional e-mail address, select ADD in step 5, and 
then specify the destination. When sending the data to an FTP 
address or SMB address, multiple addresses cannot be specified.
To check the specified e-mail address, select 
CHECK/EDIT in 
step 5. To delete an address, select 
CHECK/EDIT in step 5, and 
then continue with step 2 of “Deleting a Specified Destination 
Address”.
Searching the Address Book
The destination address (e-mail address, FTP address or SMB address) 
where the scan data is to be sent can be specified by searching the address 
book.
This feature is available only if data has been registered in the 
address book.
1With the main screen (Scan mode) or Can Use AddressBook dis-
played, press the AddressBook key four times so that 
PHONE BOOK 
appears.
2Press the + or , key to select SEARCH, and then press the Select key.
3Use the keypad to type in the search keyword (maximum of 10 charac-
ters), and then press the Select key.
Downloaded From ManualsPrinter.com Manuals 
						

							Scanning With the Machine 6-16
The search begins, and the search results appear after a while. If no data 
matches the search keyword, 
NOT FOUND appears for about two sec-
onds.
For details on entering/editing text, refer to “Entering Text” on 
page A-6.
Text starting with the first character of the maximum 10 characters 
is searched for. Text will not be found if the search keyword is in 
the middle of a word.
4Press the + or , key to select the desired data, and then press the Select 
key.
To narrow down the search results, press the Back key, and then 
perform step 3 again.
5Press the Select key again.
If an FTP address or an SMB address was selected, the destination 
address is specified.
6If an e-mail address was selected, press the + or , key to select FIN-
ISH
, and then press the Select key.
To add an additional e-mail address, select ADD in step 6, and 
then specify the destination. When sending the data to an FTP 
address or SMB address, multiple addresses cannot be specified.
To check the specified e-mail address, select 
CHECK/EDIT in 
step 6. To delete an address, select 
CHECK/EDIT in step 6, and 
then continue with step 2 of “Deleting a Specified Destination 
Address”.
Searching an LDAP Server
The destination e-mail address where the scan data is to be sent can be 
specified by using information on the LDAP server.
To connect to an LDAP server, settings for LDAP SETTING must be 
specified. For details, refer to the Reference Guide on the Documenta-
tion CD/DVD.
A maximum of 16 addresses (total of addresses from direct input and 
an LDAP search) can be specified.
If anonymous access is used to search for information on an LDAP 
server, the correct search results may not be retrieved.
1With the main screen (Scan mode) or Can Use AddressBook dis-
played, press the AddressBook key four times so that 
PHONE BOOK 
appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Scanning With the Machine6-17
2Press the + or , key to select LDAP SEARCH, and then press the 
Select key.
3Press the + or , key to select NAME or E-MAIL, and then press the 
Select key.
To search registered names, select NAME. To search e-mail 
addresses, select 
E-MAIL.
4Use the keypad to type in the search keyword (maximum of 10 charac-
ters), and then press the Select key.
The search begins, and the search results appear after a while. If no data 
matches the search keyword, 
NOT FOUND appears for about two sec-
onds.
For details on entering/editing text, refer to “Entering Text” on 
page A-6.
Text starting with the first character of the maximum 10 characters 
is searched for. Text will not be found if the search keyword is in 
the middle of a word.
5Press the + or , key to select the desired data, and then press the Select 
key.
To check the found information, press the ) key.
An e-mail address exceeding 64 characters cannot be specified. If 
such an e-mail address is specified, 
ADDRESS IS TOO LONG 
appears for about two seconds, and then the screen for specifying 
the destination address appears.
To narrow down the search results, press the Back key, and then 
perform step 4 again.
6Press the Select key again.
7Press the + or , key to select FINISH, and then press the Select key.
To add an additional e-mail address, select ADD in step 7, and 
then specify the destination.
To edit the specified e-mail address, select 
CHECK/EDIT in step 
7, and then continue with step 2 of “Editing a Specified Destination 
Address”.
To delete a specified e-mail address, select 
CHECK/EDIT in step 
7, and then continue with step 2 of “Deleting a Specified Destina-
tion Address”. The address cannot be edited.
Downloaded From ManualsPrinter.com Manuals