Konica Minolta bizhub 211 User Manual

							Advanced copy operations6
bizhub 163/211 6-33Copying with a recalled copy program
1Position the document to be copied.
– Refer to Loading the document on page 4-18.
2Press the [Mode Memory] key.
3Press the [+] or [,] key until RECALL is selected, and then press the 
[OK] key.
4Press the [+] or [,] key until the desired program number is selected, 
and then press the [OK] key.
5Press the [Start] key.
MODE MEMORY
REGISTER
RECALL
MODE MEMORY REGIST.
PROGRAM2
PROGRAM1
Downloaded From ManualsPrinter.com Manuals 
						

							6Advanced copy operations
6-34 bizhub 163/211
6.9 Copying using an account number
If account numbers have been specified, use of the machine can be limited 
to specific users or to a specified number of copies for each account.
The following procedure describes how to make copies after entering an 
account number.
Entering the account number
!
Detail 
If account numbers have been specified, the machine cannot be used 
unless the account number is entered first.
In order to use this function, the account numbers must be specified 
using the account track parameters (displayed from the ADMIN. 
MANAGEMENT menu in the Utility mode). Refer to page 7-37.
1Using the keypad, type in the three-digit account number.
– To correct the entered account number, press the [Clear/Stop] key, 
and then type the number in correctly.
 ACCOUNT NO.:---
 ACCOUNT NO.:***
 (PRESS ACCESS KEY)
Downloaded From ManualsPrinter.com Manuals 
						

							Advanced copy operations6
bizhub 163/211 6-35
2Press the [Access] key.
The basic screen appears and 
copying can be started.
3Position the document(s) to be copied, and then select the desired 
copy settings.
– Refer to Before making copies on page 4-3.
– Refer to Advanced copy operations on page 6-3.
4Press the [Start] key.
5When you are finished making copies, press the [Access] key again.
Downloaded From ManualsPrinter.com Manuals 
						

							6Advanced copy operations
6-36 bizhub 163/211
Downloaded From ManualsPrinter.com Manuals 
						

							7Utility mode/Copy mode 
parameters
Downloaded From ManualsPrinter.com Manuals 
						

							Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode/Copy mode parameters7
bizhub 163/211 7-3
7 Utility mode/Copy mode parameters
7.1 Utility mode
There are eight parameter in the Utility mode.
2
Note 
Depending on the options installed, some parameters may not be 
available. If an unavailable parameter is selected, an error message 
appears.
No.NameDescriptionPage reference
1 MACHINE SET-
TINGUsed to specify settings for the machine’s oper-
ating environment.p. 7-6
2PAPER SOURCE 
SETUPUsed to specify the size and type of paper load-
ed in the 1st paper drawer. In addition, settings 
can be specified for the paper drawers that are 
selected during the automatic tray switching op-
eration.p. 7-20
3 CUSTOM SIZE 
MEMORYUsed to register up to two custom paper sizes. p. 7-30
4USER MANAGE-
MENTUsed to perform maintenance operations in or-
der to maintain the machine’s efficiency.p. 7-33
5ADMIN. MAN-
AGEMENTUsed by the administrator to specify settings for 
managing the accounts and to specify remote 
monitoring settings.p. 7-37
6 COPY SETTING 1 Used to specify the default settings for the vari-
ous copy functions.p. 7-56
7 COPY SETTING 2 p. 7-72
8 DIAL REGISTRA-
TIONThis menu item appears only when optional im-
age controller IC-206 or network interface card 
NC-503 is installed.
Specify speed dial settings.
For details, refer to the user manual for the cor-
responding option.-
9 SCAN SETTING Used to specify settings when optional image 
controller IC-206 or network interface card NC-
503 is installed on the machine. For details, refer 
to the user manual for the corresponding option.-
Downloaded From ManualsPrinter.com Manuals 
						

							7Utility mode/Copy mode parameters
7-4 bizhub 163/211
7.2 Utility mode/Copy mode parameters
* indicates manufacturer’s default settings.
MenuParameterSettings
MACHINE SET-
TINGAUTO PANEL RESET OFF / 30sec / 1min* / 2min / 3min / 4min / 5min
ENERGY SAVE MODE 1 to 240 minutes (default: 15 minutes)
AUTO SHUT OFF OFF* / ON (15 to 240 minutes)
DENSITY (ADF) MODE 1* / MODE 2
DENSITY (BOOK) MODE 1* / MODE 2
PRINT DENSITY
LCD CONTRAST
KEY SPEED SETTING TIME TO START (0.1sec / 0.3sec / 0.5sec / 
1.0sec* / 1.5sec / 2.0sec / 2.5sec / 3.0sec)
INTERVAL (0.1sec / 0.3sec / 0.5sec / 1.0sec / 
1.5sec / 2.0sec / 2.5sec / 3.0sec)
LANGUAGE ENGLISH* / GERMAN / FRENCH / ITALIAN / 
DANISH / DUTCH / SPANISH / NORWEGIAN / 
SWEDISH / FINNISH / TURKISH / PORTU-
GUESE
PAPER SOURCE 
SETUPINCH/METRIC Each tray: INCH / METRIC*
TRAY1 PAPER PAPER SIZE (AUTO* / SIZE INPUT)
MEDIA TYPE (PLAIN* / TRANSPARENCY / 
CARD / ENVELOPE)
PAPER TYPE PLAIN* / RECYCLE / SPECIAL
CUSTOM SIZE 
MEMORYMEMORY1 X: 140 mm to 432 mm
Y: 90 mm to 297 mm
MEMORY2
USER MANAGE-
MENTDRUM DEHUMIDIFY -
TONER REPLENISHER -
ADMIN. MAN-
AGEMENTADMINISTRATOR NO. 000000-999999
AUTO SHUT OFF DISABLE / ENABLE*
ACCOUNT TRACK ACCOUNT TRACK MODE (ON* / OFF)
ACCOUNT NO. REG. (ADD / CHECK/EDIT)
ACCOUNT TRACK DATA (DISPLAY* / ALL 
COUNTER CLEAR / LIST)
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode/Copy mode parameters7
bizhub 163/211 7-5
COPY SETTING 1 PAPER PRIORITY TRAY1* / TRAY2 / TRAY3 / TRAY4 / TRAY5 / 
MULTI BYPASS
QUALITY PRIORITY TEXT/PHOTO* / TEXT / PHOTO
DENSITY PRIORITY AUTO* / MANUAL
DENSITY LEVEL AUTO
MANUAL
BINDING POSITION LEFT* / RIGHT
MARGIN SETTING 0 mm to 20 mm (default: 10 mm)
ERASE SETTING LEFT* / UPPER / FRAME
(5 to 20 mm; default: 10 mm)
SMALL ORIGINAL DISABLE* / ENABLE
COPY SETTING 2 COPY PRIORITY AUTO PAPER SELECT* / AUTO ZOOM / MAN-
UAL
OUTPUT PRIORITY NON-SORT* / SORT / GROUP
4IN1 COPY ORDER PATTERN1* / PATTERN2
MIXED ORIGINAL OFF* / ON
DUPLEX COPY OFF / ON*
CRISSCROSS MODE OFF / ON*
MenuParameterSettings
Downloaded From ManualsPrinter.com Manuals 
						

							7Utility mode/Copy mode parameters
7-6 bizhub 163/211
7.3 MACHINE SETTING
From the MACHINE SETTING menu, the following machine settings can be 
changed.
MACHINE SETTING parameters
No.MACHINE SET-
TINGDescription
1 AUTO PANEL RE-
SETThis parameter can be used to specify the length of time until the 
auto panel reset operation is performed after copying or the oper-
ation for the last key pressed is finished. When the auto panel reset 
operation is performed, the machine automatically returns to the 
default mode and the basic screen is displayed.
The manufacturer’s default setting is 1 minute.
2 ENERGY SAVE 
MODEThis parameter can be used to specify the length of time that the 
machine is idle before it enters Power Save mode.
The manufacturer’s default setting is 15 minutes.
3 AUTO SHUT OFF This parameter can be used to specify the length of time that the 
machine is idle before it is turned off.
The manufacturer’s default setting is OFF.
4 DENSITY  (ADF) This parameter can be used to specify the image quality level when 
the optional document feeder is used.
MODE1: Select this setting to lighten the copy density and reduce 
spots in the copy.
MODE2: Select this setting to produce copies at the same density 
as that of the document.
The manufacturer’s default setting is MODE1.
5 DENSITY (BOOK) This parameter can be used to specify the density level when a 
document placed on the original glass is copied.
MODE1: Select this setting to produce copies at the same density 
as that of the document.
MODE2: Select this setting to lighten the copy density and reduce 
spots in the copy.
The manufacturer’s default setting is MODE1.
6 PRINT DENSITY This parameter can be used to select one of the five density levels 
for printing.
The manufacturer’s default setting is  .
7 LCD CONTRAST This parameter can be used to adjust the contrast of the control 
panel display.
The manufacturer’s default setting is  .
8 KEY SPEED SET-
TINGThis parameter can be used to specify the length of time until re-
peating input begins after a key is held down and the repeating in-
terval.
The manufacturer’s default setting is 1.0sec for TIME TO 
START and is 0.1sec for INTERVAL.
9 LANGUAGE The display language can be selected.
The manufacturer’s default setting is ENGLISH.
10 SCAN THRESHOLD This parameter appears only when optional image controller IC-
206 or network interface card NC-503 is installed.
This parameter can be used to specify the amount of memory that 
is available before the memory becomes full and scanning stops.
For details, refer to the user manual for the corresponding option.
Downloaded From ManualsPrinter.com Manuals