JVC Projector Dla Rs60u3d Instructions Manual

							21
ENGLISH
Installing the Projector and Screen
Set Angle
Shift 
About installation (Continued)
While installing, please place this unit and the screen perpendicular to each other. Failing 
to do so may  increase trapezoidal distortion.  (Reference page: 36, 52)
The angle range which can be set for this unit is ±30°.
■ 
Left/Right position 
　 *  0% up/down position (center)
■  
Up/Down position
　 * 
0% left/right position (center)
Lens shift correlation chart:
● Malfunctions may occur if the angle is not set within the above-mentioned range.
Approximately 34% (maximum) of the projected image  Approximately 34% (maximum) of the projected image 
Approximately 80% 
(maximum) of the projected 
image  Approximately 80% 
(maximum) of the 
projected image
90
80
70
60
50
40
30
20
10 0yy 10y   20
yy

30y     40
Horizontal lens shift¢Ë£ 


Vertical lens shift ¢Ë£ 
● Maximum Up-Down shift varies with the amount of Left-Right shift. 
Likewise, maximum Left-Right shift varies with the amount of Up-
Down shift.
● 
The values on the chart are intended to act as a guide. Use them 
for reference during installation.
30°
30°
30°
30°
Left-Right Shift(%) 0%
10% 20%30% 34%
Up-Down Shift(%) 80%
66%47%18% 0%
Lens movability 
range
■
 
Lens shift movement        
range 
Preparation    
						

							22
Preparation
2
About installation (Continued)
Fixation of the projector
Measures to prevent the unit from toppling or dropping should be taken f\
or safety reasons and 
accident prevention during emergencies including earthquakes.
When mounting this unit on a pedestal or ceiling, remove the 4 feet on t\
he bottom surface and 
use all the 4 screw holes (M5 screws) to mount.
Ceiling
■ Bottom Surface
Air inlets 4 locations
Precautions for Mounting
● Special expertise and techniques are required for 
mounting this unit. Be sure to ask your dealer or a 
specialist to perform mounting.
● Depth of the screw holes (screw length) is 23 
mm. Use screws shorter than 23 mm but longer 
than 13 mm. 
Using other screws will result in 
malfunctioning or cause the unit to drop.
● When mounting to a pedestal, ensure 
sufficient space (foot height of 10 mm or 
higher) around the unit so that 
the air inlets 
are not blocked.
● Do not tilt this unit more than ±5 degrees 
from side to side when using.
●  Regardless whether the unit is still under 
guarantee, 
JVC is not liable for any product 
damage caused by mounting the unit with non-
JVC ceiling fittings or when the environment is 
not suitable for ceiling-mount.
● When using the unit hanging from a ceiling, 
pay attention to the surrounding temperature. 
When a heater is in use, temperature around 
the ceiling is higher than expected.     
						

							23
ENGLISH
About installation (Continued)
Determine the distance from the lens to the screen to achieve your desir\
ed screen size. 
This unit uses a 2.0x power zoom lens for projection. 
Screen Size and Projection Distance
■ Relationship Between Projection Screen Size and Projection Distance
P
ro je ctio n S cre en S iz e
(Height, Width) 
Aspect Ratio 16:9 A
ppro xim ate  P ro je ctio n 
Distance
W(Wide) to  T(Tele)
140"
(Approx.1.7, 3.1m) Approx.4.23 m 
to
  
Approx.8.60m
150"
(Approx.1.9, 3.3m) Approx.4.53m 
to
  
Approx.9.22m
160"
(Approx.2.0, 3.5m) Approx.4.84m 
to
  
Approx.9.84m
170"
(Approx.2.1, 3.8m)  
Approx.5.14m  to
  
Approx.10.45m
180"
(Approx.2.2, 4.0m)  
Approx.5.45m  to
  
Approx.1 1.07m
190"
(Approx.2.4, 4.2m)  
Approx.5.75m  to
  
Ap
prox.1 1.68m
200"
(Approx.2.5, 4.4m)  
Approx.6.06m  to
 
Approx.12.30m
P ro je ctio n S cre en 
Size
(Height, Width) 
Aspect Ratio 16:9  A
ppro xim ate  P ro je ctio n 
Distance
W(Wide) to  T(Tele)
60 "
( Approx. 
0.7, 1.3m) Approx.1.78m 
to
  
Approx.3.66m
70"
(Approx.0.9, 1.5m) Approx.2.09m 
to
 Approx.4.28m
80"
(Approx.1.0, 1.8m) Approx.2.40m 
to
 Approx.4.89m
90"
(Approx.1.1, 2.0m) Approx.2.70m 
to
 Approx.5.51m
100"
(Approx.1.2, 2.2m) Approx.3.01m 
to
 Approx.6.13m
1 10"
(Approx.1.4, 2.4m) Approx.3.31m 
to
 Approx.6.75m
120"
(Appro
x.1.5, 2.7m) Approx.3.62m 
to
 Approx.7.36m
130"
(Approx.1.6, 2.9m) Approx.3.92m 
to
 Approx.7.98m
Effective Range of Remote Control Unit
■  
  When directing the remote control toward this 
unit. 
● When aiming the remote control towards the 
remote sensor on this unit, ensure that the 
distance to the sensor in front or at the rear of 
this unit is within 7 m.
●  If the remote control fails to work properly , move 
closer to this unit.
■  
  When reflecting off a screen
●Ensure that the total of distance A between this 
unit and screen and distance B between remote 
control and screen is within 7 m.
● As the efficiency of signals reflected from the 
remote control unit differ with the type of screen 
used, operable distance may decrease.
30°
30°
20° 20°
30°
30°
20° 20°
A
B
This unit
This unit
Remote control
Screen Remote control 
Preparation    
						

							24
Preparation
2
About the connection
T ypes of possible input signals (PC compatible)
● HDMI
No.DesignationResolution fh
[kHz] fv
[Hz] dot CLK
[MHz] T
otal No. 
of dots [dot] T
otal No. 
of lines [line] No. of 
ef fective 
dots
[dot] No. of 
ef fective 
lines [line]
1 VGA 60
640 X 480 31.50060.000 25.200 800525 640 480
2 VGA 59.94
640 X 480 31.46959.940 25.175 800525 640 480
3 SVGA 60
800 X 600 37.87960.317 40.000 1,056 628800 600
4 XGA 60
1024 X 768  48.36360.004 65.000 1,344 8061,024 768
5 WXGA  60
1280 X 768 47.76060.000 79.998 1,675 7961,280 768
6 WXGA  +60
1440 X 900 55.91959.999106.470 1,9049321,440 900
7 SXGA 60
1280 X 1024 63.98160.020108.000 1,6881,066 1,280 1,024
8 WSXGA  +60
1680 X 1050 65.22260.002147.140 2,2561,087 1,680 1,050
9 WUXGA  60
1920 X 1200 74.03859.95154.000 2,0801,235 1,920 1,200
● PC (D-sub 3-lines 15 pins)
No.DesignationResolution fh
[kHz] fv
[Hz] dot CLK
[MHz] T
o ta l  N o. 
of dots [dot] T
otal 
No. of  lines
[line] No. of 
ef fective 
dots
[dot] No. of 
ef fective 
lines [line]
1 VGA 60
640 X 480 31.50060.000 25.175 800525 640 480
2 VGA 72
640 X 480 37.90072.000 31.500 832520 640 480
3 VGA 75
640 X 480 37.50075.000 31.500 840500 640 480
4 VGA 85
640 X 480  43.30085.000 36.000 832509 640 480
5 SVGA 56
800 X 600 35.20056.000 36.000 1024625 800 600
6 SVGA 60
800 X 600 37.90060.000 40.000 1056628 800 600
7 SVGA 72
800 X 600 48.10072.000 50.000 1040666 800 600
8 SVGA 75
800 X 600 46.90075.000 49.500 1056625 800 600
9 SVGA 85
800 X 600 53.70085.000 56.250 1048631 800 600
10 XGA 60
1024 X 768 48.40060.000 65.000 13448061024 768
11 XGA 70
1024 X 768 56.50070.000 75.000 13288061024 768
12 XGA 75
1024 X 768 60.00075.000 75.750 13128001024 768
13 XGA 85
1024 X 768 68.70085.000 94.500 13768081024 768
14 WXGA 60
1280 X 768 47.76060.000 79.998 16757961280 768
15 WXGA+  60
1440 X 900 55.91959.999 106.470 19049321440 900
16 SXGA 60
1280 X 1024 64.00060.000 108.000 1688      1066 1280 1024
17 SXGA+  60
1400 X 1050 63.98160.020 108.000 16881066 1400 1050
18 WSXGA+  60
1680 X 1050 65.222
60.002147.140 22561087 1680 1050
19 1920x1080 60 1920 X 108067.50060.00148.500 22001125 1920 1080
20 MAC13"
640 X 480 35.00066.667 30.240 864525 640 480
21 MAC16"
832 X 624 49.10775.087 55.000 1120654 832 624
22 MAC19"
1024 X 768 60.24174.927 80.000 13288041024 768     
						

							25
ENGLISH
About the connection (Continued)
● Do not turn on the power until connection is complete. 
● The connection procedures dif fer according to the device used. For details, refer to the instruction 
manual of the device to be connected.
●  This device is used for image projection. Connect to an audio output device such as amplifier and 
speaker for audio output from the connected device.
● The images may not be displayed depending on the devices and cables to be connected.
For HDMI cable (sold separately), only use one that is HDMI-approved. 
●  It may not be possible to connect to this unit depending on the dimension of the connector cover of the 
cables to be connected. 
1        HDMI         2
RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUTOK
T
o connect via HDMI 
terminal
(Reference page: 26)
Connection to the unit
To connect via video terminal  (Reference page: 27)
Connection by LAN terminal (Reference page: 30) 
To connect via PC terminal (Reference page: 28) 
Connection by 3D SYNCHRO 
terminal (Reference page: 28) Connection by REMOTE terminal (Reference page: 30)
T
o connect RS-
232C terminal
(Reference  
page: 29)
PC  VCR and  
camcorder
BD/DVD Recorder 
BD/DVD Player 
To connect via Trigger terminal 
(Reference page: 29)
RS50RS50RS60
RS50RS50RS60 
Preparation    
						

							26
Preparation
2
About the connection (Continued)
■  Connecting via HDMI Cable
■ Connecting via HDMI-DVI Conversion Cable
1        HDMI         2
RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUT
OK
1        HDMI         2
RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUT
OK
This unit
This unit BD/DVD recorder
HDMI cable (sold separately)
HDMI output terminal
Notebook PC
● 
If noise is produced, take PCs (Notebook PC) away from this unit.
● 
For a transmission bandwidth in compliance with the HDMI standard, a 340MHz cable is recommended. 
In case a cable is used for transmission bandwidth of 75MHz, it is recommended to choose 1080i or 
less for the transmitting equipment.
●  If the video is not displayed, try to reduce the length of the cable or lowering the resolution of the video 
transmitting equipment.
●  If noise is produced, take PCs (desktop computer
) away from this unit.
● If the video is not displayed, try to reduce the length of the cable or lowering the resolution of the video 
transmitting equipment. HDMI-DVI conversion cable
(sold separately) DVI output terminal
Desktop computer 
HDMI  1  input terminal
HDMI  2  input terminal
HDMI  1  input terminal
HDMI  2  input terminal     
						

							27
ENGLISH
About the connection (Continued)
1        HDMI         2RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUTOK
CBD/DVD player
Component video output  terminals
Y (green)
C
R/PR (red)
C
B/PB (blue)
●  Set “COMP.” in the setting menu to “Y Pb/Cb Pr/Cr”. 
(Reference page: 52)
This unit
To component video input terminals
Component video cable  (sold separately)
■  
Connecting via RGB V
ideo Cable
● Set  “
COMP .”
 in the setting menu to  “
RGB ”
. (Reference page: 52)
●  For information on compatible input signals, see  “
Specifications ”
.(Reference page: 73)
1        HDMI         2
RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUT
OK
This unit
Device equipped with 
RGB output
RGB video cable (sold separately) RGB video output terminals
R(Red)
B(Blue)
G(G re en ) 
(In clu des s yn c 
signals)
T o RGB video input terminals
■ 
Connecting via Component V
ideo Cable 
Preparation    
						

							28
Preparation
2
RS50RS5 0RS60■ Connecting via PC Cable 
About the connection (Continued)
1        HDMI         2
RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUT
OK
This unit
● 
For information on supported input signals, please refer to 
“Specifications
”.(Reference page: 73)
PC cable
(sold separately
)
To PC input terminal
VGA output terminal
Notebook PC
■  
Connected by a 3D SYNCHRO terminal
1        HDMI         2
RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUT
OK
This unit
● 
3D synchro emitter:  This is a dedicated terminal for PK-EM1 (sold separately).
● 3D glasses (PK-AG1-B) is an optional device, and is not included in the 3D synchro emitter .
           
                      
●  Note that converting 2D images to 3D ones using the 3D feature of this product, and playing them for
    commercial purposes or for broadcasting in public places may infringe the rights of aut
hors protected 
    under the copyright laws.
● 3D 
images  may appear  different  depending  on the  ambient  temperature  and lamp  usage.  Stop using  the 
projector if images cannot be projected correctly .
●  Before you watch 3D video images, make sure to read "3D description of the system" 
    (Reference page 57 to 59).
3D synchro emitter
3D-glasses
CAUTION     
						

							29
ENGLISH
About the connection (Continued)
■ Connecting via T
rigger Cable
1        HDMI         2
RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUTOK
This unit
     
●  Do not supply the power to the other devices.
● 
Do not connect audio terminals of the other devices such as headphones etc. Otherwise, this may 
cause a malfunction of the other devices or injury. 
● Using beyond the rated value will cause malfunction.
● Exercise adequate caution to prevent short circuit as the trigger terminal outputs a voltage of 12V.
● 
T he d efa ult  is  s e t to  " N o o utp ut" . P le ase  s e t it  u nder th e it e m  " T rig ger"  o f m enu [5 ] " F unctio n" ( R efe re nce 
page: 54). Screen
T rigger cable
 (sold separately)
T rigger input terminal 
( Φ 3.5)
1        HDMI         2
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUT
OK
■
 Connected by RS-232C connection cable
This unit
RS-232C 
 
terminal
RS-232C connection cable (sold separately)
To Trigger output terminal
CAUTION 
Preparation    
						

							30
Preparation
2
About the connection (Continued)
■  Connected by LAN terminal  
1        HDMI         2
RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUT
OK
This unit
● 
The network is used to control the unit. It is not used for transmission of the video signal.
● Please contact your network administrator for questions concerning the network connection. Network
HUB
Server
1        HDMI         2 RS-232-C
3D C
R/PRCB/PB   Y
SYNCHRO PC
TRIGGERREMOTE
CONTROL
STANDBY/ON
MENUBACK
INPUT
OK
■
 Connected by a REMOTE terminal
This unit
Exte rn al  in fr a re d s e nso r 
(sold separately)
●  F or  a n e xte rn al  in fr a re d s e nso r  a nd c o nnectin g c a ble ,  p le ase  c o nta ct  y o ur  d eale r  o r  a  J V C  s e rv ic e 
center .
connection cable(sold separately)
connection cable
   (sold separately)
RS50RS5 0RS60