HP Color LaserJet CP6015xh User Manual
Have a look at the manual HP Color LaserJet CP6015xh User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Install memory You can install more memory for the product by adding a dual inline memory module (DIMM). CAUTION:Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap, or frequently touch the surface of the DIMM antistatic package and then touch bare metal on the product. Install DDR memory DIMMs 1.Turn the product off. 2.Disconnect all power and interface cables. ENWWReplace supplies 157
3.Locate the black formatter pressure release tabs on the formatter board in the rear of the product. 4.Gently press the black tabs toward each other. 5.Gently pull on the black tabs to pull the formatter board from the product. Place the formatter board on a clean, flat, grounded surface. 158 Chapter 11 Manage and maintain the product ENWW
6.To replace a DIMM that is currently installed, spread the latches apart on each side of the DIMM slot, lift the DIMM up at an angle, and pull it out. If you are adding a DIMM, use the other slot provided. XOXOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXO XOXOXOXOXO XOXOXO XOXO XOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXOXOXO XOXOXOXOXOXO 7.Remove the new DIMM from the antistatic package. Locate the alignment notch on the bottom edge of the DIMM. 8.Holding the DIMM by the edges, align the notch on the DIMM with the bar in the DIMM slot at an angle and firmly press the DIMM into the slot until it is fully seated. When installed correctly, the metal contacts are not visible. XOXOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXO XOXOXOXO XO XOXOXOXOXO XOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXOXOXO XOXOXOXOXOXO 9.Push down on the DIMM until both latches engage the DIMM. XOXOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXO XOXOXOXOXOXO XOXOXOXOXOXOXOXOXOXO XOXOXOXOXOXO XIOXIOXIXO OXIXO XIOXIOXIOXIOXIXO OX I X O XIOXIOXIOXIOXIXO OXIXO XIOXIOXIOXIOXIXO OXIXO XIOXIO NOTE:If you have difficulty inserting the DIMM, make sure the notch on the bottom of the DIMM is aligned with the bar in the slot. If the DIMM still does not go in, make sure you are using the correct type of DIMM. ENWWReplace supplies 159
10.Align the formatter board in the tracks at the bottom of the slot, and then slide the board back into the product. NOTE:To prevent damage to the formatter board, ensure the formatter board is aligned in the tracks. 11.Reconnect the power cable and interface cables, and turn the product on. 12.To enable the new memory, see the following section. Enable memory for Windows 1.Windows XP and Windows Server 2003 (using the default Start menu view): Click Start, click Settings, and then click Printers and Faxes. -or- Windows 2000, Windows XP, and Windows Server 2003 (using the Classic Start menu view): Click Start, click Settings, and then click Printers. -or- Windows Vista: Click Start, click Control Panel, and then in the category for Hardware and Sound click Printer. 2.Right-click the driver icon, and then select Properties. 3.Click the Device Settings tab. 4.Expand the area for Installable Options. 160 Chapter 11 Manage and maintain the product ENWW
5.Next to Printer Memory, select the total amount of memory that is installed. 6.Click OK. Install an HP Jetdirect or EIO print server card or EIO hard disk This product is equipped with an external I/O (EIO) slot. You can install an additional HP Jetdirect print server card in the available EIO slot. 1.Turn the product off. 2.Disconnect all power and interface cables. ENWWReplace supplies 161
3.Locate an open EIO slot. Loosen and remove the two retaining screws holding the cover for the EIO slot, and then remove the cover. You will not need these screws and the cover again. They can be discarded. 4.Firmly insert the HP Jetdirect print server card into the EIO slot. 5.Insert and tighten the retaining screws that came with the print server card. 162 Chapter 11 Manage and maintain the product ENWW
6.Reconnect the power cable and remaining interface cables, and turn the product on. 7.Print a configuration page. An HP Jetdirect configuration page that contains network configuration and status information should also print. If it does not print, turn the product off, and then uninstall and reinstall the print server card to ensure that it is completely seated in the slot. 8.Perform one of these steps: ●Choose the correct port. See the computer or operating system documentation for instructions. ●Reinstall the software, choosing the network installation this time. Replace the staple cartridge If the optional HP 3-bin Stapler/Stacker Accessory or HP Booklet Maker/Finisher Accessory runs out of staples while it is stapling a print job, the product automatically stops, if set to stop when out. If the product is set to continue when out, the product will continue to print without stapling. NOTE:Only replace the staple cartridge unit when the stapler/stacker or booklet maker has run out of staples. Removing the staple cartridge at other times can cause an error to occur. NOTE:When the stapler/stacker or booklet maker runs out of staples, the stapler unit will return to its default position automatically. Replace the staple cartridge 1.Open the front door of the booklet maker or stapler/stacker. ENWWReplace supplies 163
2.Push up to on the staple cartridge to remove it from the booklet maker or stapler/stacker. 3.Insert the replacement staple cartridge unit into the stapler unit. 4.Push the staple cartridge unit into the stapler unit until it clicks into position. 5.Close the front door. 164 Chapter 11 Manage and maintain the product ENWW
Replace saddle stitch staple cartridges in the booklet maker 1.Open the front door of the booklet maker. 2.Grasp the blue handle and pull the staple carriage out of the booklet maker. 3.Grasp the small blue handle on the staple cartridge unit and pull it toward you, then swing the staple cartridge unit into an upright position. 2 1 4.Grasp the edges of each staple cartridge and pull up firmly to remove the staple cartridges from the staple cartridge unit. ENWWReplace supplies 165
5.Unpack the new cartridges and remove the plastic packing lock from each one. 6.Hold the new cartridges so that the arrows on the cartridges align with the arrows on the staple cartridge unit and insert them into the unit. 7.Pull the handle of the staple cartridge unit toward you and rotate it downward to its original position. Lock it into position by pushing in the handle. 1 2 8.Push the staple carriage back into the booklet maker finisher. 166 Chapter 11 Manage and maintain the product ENWW