HP Color LaserJet CM2320nf User Manual
Have a look at the manual HP Color LaserJet CM2320nf User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
2.Lower the jam-access tray. 3.Remove the jammed sheet by pulling it straight out. 4.Close the jam-access tray. 5. Replace tray 2. 6.Press OK to continue printing. ENWW Clear jams 209
Clear jams in tray 3 1.Pull out tray 3 and place it on a flat surface. 2.Remove the jammed sheet by pulling it straight out. 3.Replace tray 3. 4.Press OK to continue printing. 210 Chapter 15 Problem solve ENWW
Clear jams in fuser area 1.Open the rear door. 2.If necessary, push the guide (callout 1) and remove any visible paper (callout 2) from the bottom of the delivery area. NOTE: If the sheet tears, make sure that all fragments are removed before you resume printing. Do not use sharp objects to remove fragments. 3. Close the rear door. ENWW Clear jams 211
Clear jams in output bin 1.Look for jammed paper in the output bin area. 2. Remove any visible media. With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the product. NOTE: If the sheet tears, make sure that all fragments are removed before resuming printing. 3.Open and then close the rear door to clear the message. Clear jams in duplexer (duplexing models only) 1.Open the rear door. 212 Chapter 15 Problem solve ENWW
2.If necessary, pull the guide (callout 1) and remove any visible paper (callout 2) from the bottom of the delivery area. 3.If necessary, remove any visible paper from bottom side of the duplexing unit. 4.If you can not see any jammed paper, lift the duplexing unit using the tab on the side of the duplexing unit. 5.If you can see the trailing edge of the paper, remove the paper from the product. ENWW Clear jams 213
6.If you can see the leading edge of the paper, remove it from the product. 7.Close the rear door. 214 Chapter 15 Problem solve ENWW
Clear jams from the ADF Occasionally, media becomes jammed during a fax, copy, or scan job. You are notified of a media jam by the Doc feeder jam Clear, Reload message that appears on the product control-panel display. ● The ADF input tray is loaded incorrectly or is too full. See Load paper and print media on page 59 for more information. ● The media does not meet HP specifications, such as those for size or type. See Paper and print media on page 53 for more information. 1. Open the ADF cover. NOTE: Verify that any shipping tape inside the ADF has been removed. 2.Lifting the green lever, rotate the pick mechanism until it stays open. ENWW Clear jams 215
3.Gently try to remove the page without tearing it. If you feel resistance, go to the next step. 4.Open the ADF lid and gently loosen the media by using both hands. 5.When the media is free, gently pull it out in the direction shown. 216 Chapter 15 Problem solve ENWW
6.Close the lid to the flatbed scanner. 7.Lower the green lever. 8.Reinstall the cleanout part by inserting it as shown. Push down on the two tabs until the part snaps into place. Install the cleanout part correctly, because future jamming might occur if the cleanout part is not replaced correctly. ENWW Clear jams 217
9.Close the ADF lid. Avoid repeated jams ●Verify that the input tray is not overfilled. The input tray capacity varies depending on the type of print media that you are using. ● Verify that the media guides are properly adjusted. ● Check that the input tray is securely in place. ● Do not add print media into the input tray while the product is printing. ● Use only HP-recommended media types and sizes. See Paper and print media on page 53 for more information about print media types. ● Do not fan media prior to loading it in a tray. To loosen the ream, hold it firmly in both hands and twist the media by rotating your hands in the opposite direction. ● Do not let print media stack up in the output bin. The print media type and the amount of toner used affect the output bin capacity. ● Check the power connection. Make sure that the power cord is firmly connected to both the product and the power supply box. Plug the power cord into a grounded power outlet. 218 Chapter 15 Problem solve ENWW