GE F650 Manual

							CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-9
Table 3-2:  Types of f iles generated by EnerVista 650 Setup software, online 
Settings & Conf iguration File *.650Logic Conf iguration Files (*.pep, *.aut , *.lib)
*.pep*.aut*.lib
Description Settings and Conf iguration Section Header for Logic 
pr

oject Graphical edition 
cont
ainer. Logic 
equations (Virtual 
Outputs) in FDB 
format . User programmable 
lo
gic objects
Created by EnerVista 650 Setup Logic configuration 
grap

hic editor (PLC 
Editor) Logic conf iguration 
graph
ic editor (PLC 
Editor) Logic conf iguration 
graph
ic editor (PLC 
Editor)
Contents Relay conf iguration f ile containing all  elements, 
settings, input/output and LE

Ds conf iguration, graphic 
display conf iguration, etc.
Equations corresponding to the logic created and 
compiled in the PL

C Editor PLC project f ile 
cont

aining the 
necessary 
information 
relative to the relay 
model, logic 
libraries included in 
the project (*.lib), 
graphic file name 
(*.aut), etc. PLC Project f ile 
cont
aining all the 
drawings used by 
the logic, required 
by 650 relay based 
on IEC 61131-3 
standard. 
Functional block 
diagram (FDB). Library f ile to be 
i
ncluded as an object 
in a PLC project . 
Logic packages that 
can be stored into 
libraries and be 
distributed in 
different PLC 
projects.
How to 
tra
 nsfer to 
relay Connect with the relay (
Comm unications > Computer)Connect with the relay ( Communica tions > Computer)
Send settings and conf iguration from f ile Launch 650 Logic equations editor (Se
 tpoint > Logic 
Conf iguration )
Open the created PLC project ( F
 ile > Open Project)
Compile the project ( Run > Compile)
Now the logic (virtual outputs) can be sent directly to relay 
( Run > Send 

Equations to Relay ). Texts of virtual outputs are 
not stored in the relay, only in the logic conf iguration f iles to be 
edited.
Modify settings and configuration directly in the relay:
How to save EnerVista 650 Setup:
File > Get info from relay . User de
 finable texts retrieved 
are operations, events, and LEDs. PLC Editor:
File > Save Project
File > Save Library
The relay does not 
pr
 ovide this 
information unless 
the *.pep f ile is 
stored in the relay  The relay does not 
pr
ovide this 
information unless 
the *.pep f ile is 
stored in the relay. The relay does not 
pr
ovide this 
information unless 
the *.pep f ile is 
stored in the relay.
To store the logic conf iguration f iles in the relay use the 
Communication > Upload info f iles to relay  op
 tion
How to store 
in the r
 elay Communication > Upload info f iles to relay
 thr ough 
Ethernet Communication > Upload info f iles to relay
 thr ough Ethernet 
How to 
re
 trieve from 
the relay Communication > Download info f iles fr
om relay 
through Ethernet Communication > Download info f iles from relay
 thr ough 
Ethernet
REMINDER:
Logic programming support files (*.pep, *.aut, *. lib) CANNOT be retrieved directly from the relay.
It is necessary to do one of the following to store support files:
* Store in the PC 
* Upload to the relay (Communication > Upload info files to relay), after which they can be retrieved from the relay 
						

							3-10F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
3.1.5  EnerVista 650 Setup menu
The EnerVista 650 Setup menu structure is shown in Table 3-3: EnerVista 650 Setup menu structure. 
Unless specified, options are available in both online and offline mode.
(*) indicates options enabled only in online mode.  (**) indicates options enabled only in offline mode.
Table 3-3: EnerVista 650 Setup menu structure
NOTICEThe View > Language submenu allows the user to change the default language for the EnerVista 
650 Setup program. This feature is only enabled when the relay is not communicating and no file has 
been opened.
FileSetpointActualOperations(*)CommunicationIEC 61850 
CONFIGURATORSecurityViewHelp
New (**) Product 
SetupFront 
Pa
nel Fixed 
comm
ands Computer
Login userTracesInstruction 
Ma
nual
Open (**) System 
SetupStatus
Modem (*) Change 
Pa

ssword ModBus 
Mem
ory 
Map GE Multilin 
on the web
Save (**) Protection 
Elem

ents Metering
Troubleshooti
ng
 (*) User 
M
anageme
nt Languages 
(**
) About 
Ener
Vista 
650 Setup
Save As (**) Control 
Elem

ents Inputs/
Output
s Calibration (*)
Close (**) Inputs/
Output

s 
Quick 
Settings Records 
(*)
Upgrade 
Rel
ay (*)
Conf ig File
(* 650) 
Conver
 ter Relay 
Conf
iguratio
n
Compare to 
sett
 ings f ile
Properties (**) Logic 
Conf

iguratio
n Upgrade 650 
W
eb Server
Procome 
Conf
 iguratio
n Update 
M
agnetic 
Module
IEC103 
Conf
 iguratio
n
Get info from 
re
 lay (*) Clock (*)
Upload info 
f
iles to relay
Send info to 
re
 lay (*) Download 
info f
iles from 
relay
Print Setup (**)
Print Preview (**)
Print (**)
Print to f ile
PLC Checksum 
Calculation
Settings 
Checksum
  
Calculation
Order Code
Exit 
						

							CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-11
3.1.6  File menu
(*) indicates online only, (**) indicates offline only
File
New (**) Create a new settings and conf iguration f ile, with the default relay 
setti
ngs and no conf iguration 
Open (**) Open a settings and conf iguration f ile for offline working. 
Save (**)Save *.650 settings and conf iguration f ile 
Save As (**)Save as *.650 settings and conf iguration f ile.
Close (**)Close the opened *.650 f ile in EnerVista 650 Setup. 
Conf ig File (*.650) Converter Tool to convert the *.650 files from one version to another
Compare to settings f ile Compare online unit or opened settings f ile to another settings f ile
Properties (**)File properties for *.650.
Get info from relay (*)Retrieve the *.650 settings and relay conf iguration compiled equations 
fr
om the relay.
Send info to relay (*) Send and write the *.650 settings and configuration to the relay. 
Print Setup (**)To conf igure printer settings.
Print Preview (**)Preview of settings and conf iguration f ile printing format .
Print (**)Launch the *.650 f ile to be printed.
Print to f ile (*.xls) (**)*.650 printed to f ile in excel format . 
PLC Checksum CalculationCalculate the CRC of PLC equations of the .650 f ile (When a .650 is 
uploa
ded to the relay, the calculate PLC CRC and the actual value of the 
PLC CRC read from the relay must match).
Settings Checksum 
Calculation Calculate the CRC of settings of the .650 f ile (When a .650 is uploaded to 
the r
elay, the calculate Setting CRC and the actual value of the Setting 
CRC read from the relay must match).
Order code(*) Option available for F650 with f irmware version 7.00 or above. This 
allows a mode
l to have special functionality (see model selection) with 
password requirements. For detailed information go to section 9.6.3.3 
ORDER CODE UPGRADE PROCESS in chapter 9. 
Exit Quit the application closing all the open windows. 
						

							3-12F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
3.1.6.1   New, Open, Save, Save as, and Close
In these options, the EnerVista 650 Setup program opens a dialog box (with default path to Files > Config program folder) 
where the setting and configuration files  can be selected from offline files. To access this menu, there must be no 
communication between the PC program and the relay (offline mode).
Figure 3-5: Open f ile menu
Once the *.650 file for the appropriate  relay model (FXGX) is selected, the EnerVista 650 Setup program enables the offline 
options to fully program the unit. The enabled menus in the EnerVista 650 Setup program are: File, Setpoint, Actual, 
Communication, View and Help.
Offline mode displays the File, Setpoint, Actual, Communication , Security, View and Help submenus in order to program the 
unit. The Actual values submenus are for structure purposes only. Values are not refreshed while the relay is not 
communicating.
The Save as and Close file options are used to save the *.650 file into the computer and to close the current file. To work in 
offline mode for settings and configuration editing, a new *.650  file can be opened without closing the previous file. The 
Close option is instead used to clear all data in EnerVista 650 Setup program, enabling the Language, Upgrade firmware 
version and Upgrade Operating system menu options. 
						

							CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-13
3.1.6.2  Conf iguration f ile converter 
The configuration file converter tool provides automatic conversion of configuration files from and older firmware version 
to a newer version. In order to convert a configuration file, follow these steps:
1. Working in offline mode, go to File > Conf ig File (*.650) Converter
2. Select the f ile to be converted.
3. After source f ile selection is complete, select  c
 onversion settings. Make the following selections:
Source Model: Indicates source F650 model and original version of selected file.
Destination model:Drop-down list of available F650 models  and firmware versions. Select a 
destination model and firmware version. In the bottom part of this section, a 
brief description of all models affected is displayed in green after selecting one 
model in the list. 
Source file pathIndicates the path where source model file is located.
Figure 3-6: Conf ig f ile (*650) converter menu
It is possible to change the model type (FXGX) using the conversi on tool. It must be taken into account that part of the logic 
can be readjusted to fit the new input and output board selection. Notice also that the external wiring of inputs and 
outputs boards is different for type 1, 2, 4 and 5.
File conversion to version 7.50 or above   
The file conversion tool has been modified to include the increased number of setting groups available in firmware version 
7.50 and above. In firmware version 7.50, the maximum number of setting groups (SG) available increased from 3 to 6.   
Some considerations must be taken into  account previous to convert (*.650) files from firmware version below 7.50 to 
firmware version 7.50 or above. In these  cases, the tool internally checks if setting groups functionality is enabled or 
disable at Setpoint > Control Elements > Setting group in the source file and depend on its value, different conversions 
are performed in elements affected by setting groups.
Source Model
Destination Model
Source file path 
						

							3-14F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
For example, if the Phase TOC High element is config ured in the source *.650 file as described below:
                     1. Note that fields in blue contain default values
CASE 1: If the setting groups option is disabled (Setpoint > Control Elements > Setting group) in the source file, conversion 
is performed in the destination file as follows:
• Settings of different elements (Phase TOC High 1, 2 and 3)  that belong to Setting group 1(SG1) in the source f ile are 
copied into elements that belong to Setting Group 1 in the destination f ile.
• Elements in the other setting groups are conf igured with default values in the conf iguration f ile.
CASE 2: If the setting groups option is enabled (Setpoint > Control Elements > Setting group) in the source file, conversion 
to the destination file is as follows:
• Settings of different elements (Phase TOC High 1, 2 and 3) th at belong to different setting groups in the source f ile are 
copied into elements that belong to f irst group of f irst three setting groups in the destination f ile 
• Protection elements in the other groups/setting groups ar e conf
 igured with default values in the destination f ile.
Phase TOC HighPhase TOC High 1 (G1)Phase TOC High 2 
(G2)Phase TOC High 3(G3)
Function ENABLED ENABLEDENABLED
InputPHASOR(DFT)PHASOR(DFT)PHASOR(DFT)
Pickup Level 0.10 1.502.00
Curve Def inite time Def inite timeDef inite time
TD Multiplier 0.02 0.050.1
Reset
INSTANTANEOUSINSTANTANEOUSINSTANTANEOUS
Voltage Restraint
DISABLEDDISABLEDDISABLED
Snapshot Events
ENABLEDENABLEDENABLED
SG1SG2SG3SG4SG5SG6
Phase TOC HighG1G2G3G1G2G3G1G2G3G1G2G3G1G2G3G1G2G3
FunctionENABLEDDISABLED
Input                                         PHASOR(DFT)
Pickup Level0.101.502.001.00
CurveDef inite timeIEEE Ext Inv
TD Multiplier0.020.050.101.00
Reset                                      INSTANTANEOUS
Voltage 
Restraint                                     DISABLED
Snapshot Events                                    ENABLED
SG1 SG2 SG3SG4SG5 SG6
Phase TOC High G1G2G3 G1 G2G3 G1G2G3 G1G2 G3G1 G2G3 G1G2 G3
Function
ENABLEDDISABLEDENABLEDDISABLEDENABLEDDISABLED
Input                                                                                                                      PHASOR(DF T)
Pickup Level
0.101.001.501,002.001.00
Curve
Definite  timeIEEE Ext  InvDef inite timeIEEE Ext InvDef inite timeIEEE Ext Inv
TD Multiplier
0.021.000.051,000.101.00
ResetINSTANTANEOUS
Voltage 
RestraintDISABLED
Snapshot 
EventsENABLED 
						

							CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-15
3.1.6.3  Properties
When this option is selected, the program displays the relay  model information, firmware version, etc. of the file being 
edited, as shown:
Figure 3-7: File properties menu
3.1.6.4  Print options
The printing options are active only in offline mode with a file open, and not in online mode, connected with the relay.
Print setup
Option to configure the printer options and settings.
Print preview
Option to preview the whole settings and configuration f ile (*.650) in paper format to be printed as shown:
Figure 3-8: Print preview of settings f ile 
						

							3-16F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
Print
Option to print the relay configuration using the PC default (activ e) printer on port COMx or LPT. This option is active only in 
offline mode and in file edition (not in online mode while connected to the relay).
Print to f ile (*xls)
Option to export the configuration file to an Excel file.
3.1.6.5  Compare to settings f ile
This tool provides an automatic comparison  of two different configuration files, or of an online unit to one settings file.
Open the source *.650 file and select the version and model to compare against. The results of the comparison are 
displayed as shown:
Figure 3-9: Compare to settings f ile
3.1.6.6  PLC checksum calculation
When working in offline mode, the PLC Checksum calculation option calculates the CRC of the PLC equations and Relay 
configuration section for the open *.650 file. When a *.650 file  is uploaded to the relay, the calculated PLC Checksum and 
the actual value of the PLC Checksum read from the relay (Actual values > Status > System Info) must match.
In order to calculate this checksum, the following sections of the * .650 file are considered:
• All equations compiled in the f ile and located in EnerVista 650 Setup  Setpoint > Logic conf iguration
• Conf iguration available in the f ile and located in EnerVista 650 Setup  Setpoint > Relay conf
 iguration, excluding:
– HMI tab conf iguration
– All configured text
– Opening and closing time in the Switchgear section 
						

							CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-17
3.1.6.7  Setting checksum calculation
When working in offline mode, the Settings Checksum calcul ation option calculates the CRC of different configured 
settings for the open *.650 file. When a *.650 file is uploaded to the relay, the calculated Sett ings Checksum and the actual 
value of the Settings Checksum read from the relay (Actual values > Status > System Info) must match.
In order to calculate this checksum, the following sections of the * .650 file are considered:
• All settings in the relay conf iguration section (Setpoint > Relay conf iguration) excluding:
– Those communication settings:  Setpoint > Pr
 oduct Setup > Communication settings > SerialPorts  or
Network  (Ethernet)  or Mod
 bus Protocol or Routing
– Relay calibration factors
– Opening and closing time in the Switchgear section
3.1.7  Setpoint menu
(*) indicates online only,  (**) indicates offline only
Setpoint
Product Setup Communications settings for all protocols and physical mediums. ModBus user map 
def
inition, fault report , oscillography, data logger  demand settings and T ime Settings.
System Setup General Settings, Flex Curves Def inition, Breaker settings, maintenance, switchgear 
snapshot event
s management and Miscellaneous Settings.
Protection Elements Phase, Neutral, Ground, Sensitive Ground and Negative Sequence Current Settings. 
V
oltage Elements settings and Power Settings management .
Control Elements Setting groups, under- and over-frequency settings, synchrocheck, autoreclose, breaker 
failur
e, VT fuse failure, broken conductor, locked rotor settings management , Pulse 
Counters, Analog comparators, Frequency Rate of Change, Load encroachment , max 
number of starts, Digital Counters, Cold Load Pickup and PLC T imer Masks
Inputs/Outputs Contact I/O settings for all boards available in device, Remote Comms Force Outputs and 
V
irtual inputs.
Quick Settings Menu that encompass the most important settings to conf igure the device such as; 
Curr
ent and Voltage sensing or current protection element .
Relay Conf iguration Conf iguration of Outputs, LEDs, Operations, Protection Elements, Oscillography, Control 
Event
s, Control Elements, Switchgear, Inputs, Virtual Inputs, Operations and HMI. Whole 
relay conf iguration with internal relay signals or user-def inable ones as logic (virtual 
outputs).
Logic Conf iguration Logic conf iguration graphic editor (PLC Editor). It is a PLC Project f ile editor that contains all 
the int
ernal drawings used to make the logic (virtual outputs) based on IEC 61131-3 
standard. Functional block diagram (FDB).
Procome 
Conf iguration Procome Configuration tool. Only available for Procome models (5) when communicating 
thr
ough Ethernet with EnerVista 650 Setup
IEC103 Conf iguration  IEC103 settings for available IEC103 models (3) when communicating through Ethernet 
with Ener
vista 650 Setup
Clock (*) Relay synchronization to computer clock or to user-def inable date and time. Online mode 
only. 
						

							3-18F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
3.1.7.1  Product setup menu
(*) indicates online only,  (**) indicates offline only
3.1.7.2  Communication settings menu
This section details the settings related to communication  parameters for the different protocols available in the F650.
(*) indicates online only, (**) indicates offline only
Product Setup
Communication 
Settings Serial Ports, Network (Ethernet), ModBus Protocol, DNP Slave, IEC 870-5-104,  SNTP settings 
a
nd procome (if available on model selection), PTP1588 and Routing (for f irmware version 
7.00 and higher) 
ModBus User Map ModBus user map definition. The ModBus user map is formed by 256 records, selectable 
fr
om the complete relay ModBus map.
Fault Report Fault report settings. Possibility to show fault reports on HMI screen.
OscillographyOscillography settings (trigger position, samples per cycle, etc.). The trigger and digital 
c
hannels (up to 16) must be conf igured in  Setpoint > Relay conf iguration.
Data LoggerData logger conf iguration
DemandDemand settings. The demand trigger and demand reset signals must be conf igured in 
Setpoint > R
elay conf iguration
Time Settings Time settings.
COMMUNICATIoN 
SETTINGS
Serial PortsBaud rate and parity for COM1 and COM2 serial communication ports.
Network (Ethernet)Ethernet communication parameters for ETH_1/ETH2 or ETH_E/ETH_A/ETH_B 
(Depend
ing on model) (IP Address, Netmask, Gateway IP)
NOTE: The ModBus Slave address used by Ethernet ports is the one set for 
C
 OM2.EnerVista 650 Setup software allows programming two different Ethernet 
addresses, but the f irst IP has always to be set as the second IP Address is an Alias.
ModBus Protocol ModBus Slave Addresses for serial and Ethernet communication and the ModBus port 
num
ber used for ModBus TCP/IP
DNP3 Slave Physical port , Slave Address for DNP, IP Addresses for Masters, TCP/UDP Port , 
Un
solicited Response parameters, Analog scale factors and deadbands, message 
fragment size, Binary input block.Available for standard and IEC61850 models.
IEC 870-5-104  TCP Port , Common Addr of ASDU, Cyclic Meter Period and, Synchronization Event 
settings.
Available for standard and IEC61850 models.
SNTP (*) Synchronization over Ethernet settings
PROCOMEComm port and slave number for procom e protocol. Only available forprocome models (5).
PTP 1588Precission T ime Protocol 1588 settings. (Available on fw version 7.00 or higher)
RoutingA default route and a maximum number of 6 static routes may be configured. The 
de
fault route is used as the last choice, if no other route towards a given destination is 
found.This option is only available for version 7.00 and higher.