Comdial Dxp Plus Digital Communications System Instructions Manual

							/M/66-123DXP Plus Programming Instructions
7.1.29Remote Station DisableDescription:
The remote station disable feature, when enabled, allows users at stations with the proper class
of service to dial a code and remotely disable or enable another station. Normally, you should
give this capability to the system attendant but you can assign it to any class of service that is
appropriate.
Programming:1 D Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From COS programming menu, type item number for feature and press ENTER,
6. Press SPACE bar for feature setting.
7. When finished, press ESCAPE twice.
8, Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
9. Repeat steps 4-8 for each COS or press ESCAPE to end.
Operation:DisableStation:
Enable Station:INTERCOM % 05, then dial intercom number of station
INTERCOM # 05, then dial intercom number of station
7.1.30Remote Day Exception Number/Night Exception NumberDescription:
A DISA caller may have access to an outside line where the toll restriction is based on the
DISA authorization code that is associated with a particular class of service. Remote day and
night exception numbers allow DISA callers to dial numbers that their toll restriction normally
prevents them from dialing. If a toll restriction table exception number matches one of the
exception numbers that you assign using this procedure, the DISA caller is allowed to dial the
number.
The exception number values that you can assign are 1 through 32 and NONE. You can assign
32 exception numbers to each DISA class of service. You also must assign one exception
number to each toll restriction table line entry (Section II. 7). Refer to Se&ion 8.8 for complete
DISA programming details.
Programming:1 B Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From COS programming menu, type item number for day exception number
and press ENTER.
6. Type day exception number (O-32) (n, nn, n-nn, or 0 for none) and press ENTER.
7. Repeat step 6 for night exception number.
7. When finished, press ESCAPE twice.
8. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
9. Repeat steps 4-8 for each COS or press ESCAPE to end.
7-22 Station Fsa tures Programming 
						

							7.1.31Line AnswerDescription:
This feature provides station access to a line for call answering purposes for an entire class of
service of stations. Also refer to 
Section 7.1.32. You must turn on both that feature and this one
for a line to be fully usable.
Programming:1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4.Type class of service number (l-32) and press ENTER.
5.From COS programming menu, type item number for feature and press ENTER.
6.Press CONTROL E.
7.Type a for add, r for remove and press ENTER.
8.Type line port l-240 (type as n,nn,nnn or n-nnn) to be removed or added
and press ENTER.
9.Press ESCAPE three times.
10.Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
11. Repeat steps 4-10 for each COS or press ESCAPE to end.
7.1.32Line OriginafeDescription:
This feature provides station access to a line for call originating purposes for an entire class of
service of stations. Also refer to 
Section 7.1.31. Both that feature and this one must be turned on
for a line to be fully usable.
Programming:1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4.Type class of service number (l-32) and press ENTER.
5.From COS programming menu, type item number for feature and press ENTER.
6.Press CONTROL E.
7.Type a for add, r for remove and press ENTER.
8.Type line port l-240 ( n, nn,nnn or n-nnn) to be removed or added and press ENTER.
9.Press ESCAPE three times.
10. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
11. Repeat steps 4-8 for each COS or press ESCAPE to end.
Station Features Programming 7-23 
						

							lMl66-123DXP Pius Programming Instructions
7.1.33Periodic Line Tone
Description:This when enabled, provides periodic warning tones to station users while they are busy on
certain lines. The warning tone consists of one 500 ms burst, a 100 ms off period, and 
one100
ms burst. The tone reminds the users to 
keep their conversations short on these lines. You can
enable this feature for a class of service of telephones and then specify the particular lines that
you deem applicable. Further, you can select how often the tone sounds. Also refer to Section
7.1.34 for a related feature.
Programming:1 ePress CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4.Type class of service number (l-32) and press ENTER.
5.From COS programming menu, type item number for feature and press ENTER.
6. Press CONTROL E.
7,Type a for add, r for remove and press ENTER.
8.Type line port l-240 (n, nn,nnn or n-nnn) to be removed or added and press ENTER.
9.Press ESCAPE three times.
10.Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
11. Repeat steps 4-8 for each COS or press ESCAPE to end.Periodic Line Tone Time
Description:After you enable the periodic warning tones that remind users to lceep conversations short on
certain outside lines, use this procedure to set how often that you wish the periodic warning
tones to occur
Programming:1~ Press CONTROL T for main menu.
2. From main menu, select systems and press ENTER.
3. From system menu, select timing and press ENTER.
4. From system timing menu, type item number for feature and press ENTER.
5. Press SPACE bar for feature setting and press ENTER to accept setting.
6. When finished, press ESCAPE twice.
7. Type y to accept changes, n to reject them, or r to resume editing and press 
ENTER.7-24 Station Features Programming 
						

							7.1.34Maximum Call Duration
Description:The system provides the maximum call duration feature. This feature, when enabled,
automatically cuts off calls on certain lines after a preprogrammed time. The system will not cut
off calls made to an emergency number (Section 
10.4). The system sounds a warning tone at the
busy station 10 seconds before it disconnects the call. The warning tone consists of one 800 ms
burst followed by eight 100 ms bursts. Also refer to Section 7.1.33 for a related feature.
Programming:1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4.Type class of service number (l-32) and press ENTER.
5.From COS programming menu, type item number for feature and press ENTER.
6.Press CONTROL E.
7.Type a for add, r for remove and press ENTER.
8.Type line port l-240 (n, nn,nnn or n-nnn) to be removed or added and press ENTER.
9.Press ESCAPE three times.
10.Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
11. Repeat steps 4-8 for each COS or press ESCAPE to end.
Maximum Call Duration Time
Description:After you enable the maximum call duration feature, use this procedure to set the cut off time.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select systems and press ENTER.
3. From system menu, select timing and press ENTER.
4. From system timing menu, type item number for feature and press ENTER.
5. Press SPACE bar for feature setting and press ENTER to accept setting.
6. When finished, press ESCAPE twice.
7. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.Station Features Programming 7-25 
						

							lMl66-123BXP Plus Programming Instructions
7.7.35Line Group Access
Description:Use this procedure to give a station access to line groups. Refer to Section 8.2 for other line
group considerations.
Programming:1 0 Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From COS programming menu, type item number for feature and press ENTER.
6. Type line groups 
(l-16,0 = none, type as n,n,nn or n-nn) and press ENTER.
7. When finished, press ESCAPE twice.
8. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
9. Repeat steps 4-8 for each COS or press ESCAPE to end.
7.1.36Line Group Queue
Description:Use this procedure to give a station the ability to queue for an idle line in a line group. Refer to
Section 8.2 for other line group considerations.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select station and press ENTER.
3. From station menu, select COS programming and press ENTER.
4. From the COS programming menu, type item number for feature and press ENTER.
5. When finished, press ESCAPE twice.
6. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
7. Repeat steps 4-8 for each COS or press ESCAPE to end.
7-26 Station Features Programming 
						

							7.1.37Line-To-Line Transfer (Unsupervised Conference)Description:This programming feature gives a station the ability to set up an unsupervised conference
between two lines.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From COS programming menu, type item number for feature and press ENTER.
6. Press SPACE bar for feature setting.
7. When finished, press ESCAPE twice.
8. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
9. Repeat steps 4-8 for each COS or press ESCAPE to end.
Line-To-Line Connect DurationDescription:After you have given a station the ability to set up an unsupervised conference between two
lines, use this procedure to set the maximum amount of time that an unsupervised conference
can continue between two lines. When the time out occurs, the system recalls the station from
where the user enabled the unsupervised conference.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select system and press ENTER.
3. From system menu, select timing and press ENTER.
4. From timing menu, type item number for feature and press ENTER.
5. Press SPACE bar for feature setting and press ENTER.
7. When finished, press ESCAPE twice.
8. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
Sfa tion Features Programming 7-27 
						

							/M/66-123DXP Plus Programming Instructions
7.1.36Voice Announce BlockDescription:
When you enable this programming feature a station has the ability to block voice announced
internal signalling when its user dials the proper code.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From COS programming menu, type item number for feature and press ENTER.
6. Press SPACE bar for feature setting.
7. When finished, press ESCAPE twice.
8. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
9. Repeat steps 4-8 for each COS or press ESCAPE to end.
Operation:On: INTERCOM +t+ 2
Off: INTERCOM 
# 2
7.1.39Infernal /ST HashDescription:
If industry-standard telephone users access an outside line using the line group feature and then
quickly press and release (flash) the telephone’s hookswitch, the IST will react in one of two
different ways depending upon how you program this feature. Refer to Section 72.35 for other
IST programming considerations.
qWith this feature disabled, IST users can flash the hookswitch while on an outside line and
generate a hookflash signal on the outside line; however, they cannot flash the hookswitch
to obtain an intercom dial tone. The 
Section 7.2.35 procedure sets the hookflash signal time.
This time determines whether the IST hookflash signal is long enough to recall the outside
line dial tone or short enough to access the outside line features. Refer to the CO
specifications for actual requirements.
qWith this feature enabled, IST users can flash the hookswitch while on an outside line and
obtain intercom dial tone; however, they must dial 
+ 08 after they flash the hookswitch if
they need to generate a hookflash signal on the outside line.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, 
seIect COS programming and press ENTER.
4. Type class of service number (l-32) that corresponds with class of service assigned
to the IST and press ENTER.
5. From COS programming menu, type row number for IST distinctive ringing
and press ENTER.
6. Press SPACE bar for feature setting.
7. When finished, press ESCAPE twice.
8. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
9. Press ESCAPE to end.
7-28 Station Features Programming 
						

							7.1.40Forced Account CodesDescription:
After you have enabled the account code feature for the system, set its parameters, and
programmed its list of account codes into the system, turn the feature on for a station class of
service and make it either forced or optional.If you make it a forced account code, the user
must enter an account code before the system will let him or her dial the number for an outgoing
call.Also, on incoming calls a user must enter an account code before the system will allow
him or her to make any future outgoing calls. See 
Section 10.3 for other account code
programming considerations and to 
Section 10.4 for an exception to forced account code entry.
Programming:1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4.Type class of service number (l-32) and press ENTER.
5.From the COS programming menu, type item number for account code and press ENTER.
6.Press SPACE BAR for feature setting.
7. When finished, press ESCAPE.
8.Press CONTROL N as necessary to display line number for forced account code
and press ENTER.
9.Type item number for forced account code and press ENTER.
10. Press SPACE BAR for feature setting.
11. When finished, press ESCAPE twice.
12. Type y to accept changes, n to reject them, or r to resume editing and press ENTER to end.
7.1.41Allow Busy Display (Display Of Busy Status)Description
When you activate this feature, users calling a busy station from an LCD speakerphone can read
the busy status of the called station on the telephone’s display. (for example, Busy 
with line 2).
With the feature inactive, the display shows busy but does not reveal the busy status.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From COS programming menu, type item number for feature and press ENTER.
6. Press SPACE bar for feature setting.
7. When finished, press ESCAPE twice.
8. Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
9. Repeat steps 4-8 for each COS or press ESCAPE to end.Station Features Programming 7-29 
						

							/M/66-123DXP Pius Programming instructions
7.1.42Clear Major Alarm RingDescription:
This feature allows users to clear the major alarm ring condition from a telephone station. To
make this feature available to users, you must first program a class of service as described
below and then assign that class of service to the user’s telelphone station.Programming:
1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4.Type class of service number (l-32) and press ENTER.
5.From COS programming menu, type CTRL-N to get to the page with the selection for
clearing the major alarm ring.
6.Select clear major alarm ring and press ENTER.
7.Press SPACE bar to toggle between yes or no.
8.When finished, press ESCAPE twice.
9.Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
10. Press ESCAPE to end..
OperationClear major alarm ring condition: INTERCOM #90
9.1.43Handset Volume On impacf TelephonesDescription:
You can program the handset volume feature on Impact telephones to offer the station user
more choices in selecting the handset volume level locally from his or her telephone. Normally,
users have up to 8 volume levels that they can select. However, when you program the high
level, the user’s handset volume choices increase to 13.
Programming:1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4,Type class of service number (l-32) and press ENTER.
5.From COS programming menu, type CTRL-N to get to the page with the selection for high
level handset volume.
6.Select high level handset volume and press ENTER.
7.Press SPACE bar to toggle between yes or no.
8.When finished, press ESCAPE twice.
9.Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
10. Press ESCAPE to end.
Operation:While on a call, press VOLUME UP or VOLUME DOWN once for each change of volume.
To set loudness default to a certain level,
- lift handset,
- adjust loudness using VOLUME UP or VOLUME DOWN,
- press INTERCOM and dial +#7,
- hang up.7-30 Station Features Programming 
						

							DXP Plus Programming InstructionsIMl66-123
7.1.44Restrict A RS Hookflash
(Automatic Route Selection, Hookflash Restriction)
Description:This feature enhances ARS response to hookflash action on an outside line when that action is
followed by dialed digits. With the feature enabled, the system delays response to a hookswitch
flash until after the ARS feature verifies as valid all subsequent dialed digits. With the feature
disabled, the system sends the hookflash over the line without waiting for the ARS feature to
verify the validity of subsequent dialed digits. This station class of service feature is applicable
only when the ARS feature is active.
Programming:1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4.Type class of service number (l-32) that corresponds with class of service
that you wish to modify and press ENTER.
5.From COS programming menu, type row number that corresponds with
Restrict ARS Hookflash and press ENTER.
6.Press SPACE bar for feature setting.
7.When finished, press ESCAPE twice.
8.Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
9. Press ESCAPE to end.
7.1.45Quick Transfer
Description:The quick transfer feature allows users to perform an automatic screened or unscreened transfer
of an incoming line call without pressing their telephone’s TRANSKNF button. The transfer
occurs automatically as soon as the user who answers the call dials the intercom number or
access code for the transfer location. The system begins the call transfer process as soon as the
user dials a digit on his or her dial pad,
and effects the transfer as soon as the user hangs up or
presses his or her telephone’s RELEASE button. When this feature is active, it greatly reduces
the keystrokes that users must take to transfer calls over a tie line.
Programming:1 ePress CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4.Type class of service number (l-32) that corresponds with class of service
that you wish to modify and press ENTER.
5.From COS programming menu, type row number that corresponds with
Quick Transfer and press ENTER.
6.Press SPACE bar for feature setting.
7.When finished, press ESCAPE twice.
8.Type y to accept changes, n to reject them, or r to resume editing and press ENTER.
9. Press ESCAPE to end.
Station Features Programming 7-31