Canon Pixma Ip4700 User Guide

							4.Set the number of image divisions and the pages to be printed 
If necessary, click Specify..., specify the followi ng settings in the Poster Printing dialog box, and  then
click OK. 
Image Divisions  
Select the number of divisions (vertical x horizont al). As the number of divisions increases, the
number of sheets used for printing increases, allowing yo u to create a larger poster. 
Print Cut/Paste in margins 
To leave out words Cut and Paste, uncheck this check bo x. 
Important 
This feature is unavailable when the 64-bit printer driver is used. 
Print Cut/Paste lines in margins  
To leave out cut lines, uncheck this check box.  
Pages  
To reprint only specific pages, enter the page numb er you want to print. To print multiple pages,
specify by separating the pages with commas or entering a  hyphen between the page numbers. 
Note 
You can also specify the print range by clicking the pages in the settings preview. 
5.Complete the setup  
Click OK on the Page Setup tab. 
W hen you execute print, the document will be divide d into several pages during printing.
After all poster pages have been printed, paste the  pages together to create a poster. 
Printing Only Specific Pages 
If ink becomes faint or runs out during printing, you can reprint specific pages by following the proc edure
below: 
1.Set the print range  
In the settings preview on the left of the Page Set up tab, click the pages that do not need to be
printed. 
The pages that were clicked are deleted, and only t he pages to be printed are displayed. Page 241 of 437 pages
Poster Printing
JownloadedhfromhManualsPrinterDcomhManuals  
						

							Note 
Click the deleted pages to display them again. 
Right-click the settings preview to select Print all pages or Delete all pages. 
2.Complete the setup  
After completing the page selection, click OK. 
W hen you execute print, only specified pages will b e printed. 
Important 
W hen Poster is selected, the Duplex Printing, Stapl e Side and Print from Last Page appear grayed
out and are unavailable. 
Since poster printing enlarges the document when printi ng it, the print results may become coarse. 
Page top
Page 242 of 437 pages
Poster Printing
JownloadedhfromhManualsPrinterDcomhManuals  
						

							Advanced Guide > Printing from a Computer > Printing with Other Application Software > Various Printing Methods >
Booklet Printing 
Booklet Printing 
The booklet printing function allows you to print d ata for a booklet. Data is printed on both sides of the
paper. This type of printing ensures that pages can  be collated properly, in page number order, when t he
printed sheets are folded and stapled at the center . 
The procedure for performing booklet printing is as fo llows: 
1.Open the printer driver setup window
2.
Set booklet printing  
Select Booklet from the Page Layout list on the Pag e Setup tab.
The current settings are displayed in the settings  preview on the left side of the window. 
3.Select the print paper size  
Select the size of the paper loaded in the printer from the Printer Paper Size list. 
4.Set the margin for stapling and the margin width  
Click Specify... and specify the following settings in the Booklet Printing dialog box, and then click
OK.  Page 243 of 437 pages
Booklet Printing
JownloadedhfromhManualsPrinterDcomhManuals    
						

							Margin for stapling  
Select which side should the stapling margin be on when the booklet is completed. 
Insert blank page  
To leave one side of a sheet blank, check the check  box, and select the page to be left blank. 
Margin  
Enter the margin width. The specified width from th e center of the sheet becomes the margin width
for one page.  
Page Border  
To print a page border around each document page, c heck the check box. 
5.Complete the setup  
Click OK on the Page Setup tab.  
W hen you execute print, the document is automatically printed first on one side of a sheet of paper
and then on the opposite side. 
W hen the printing is complete, fold the paper at th e center of the margin and make a booklet. 
Important 
Booklet cannot be selected when a media type other  than Plain Paper, Hagaki A or Hagaki is
selected for Media Type. 
W hen Booklet is selected, Duplex Printing, Staple S ide, Print from Last Page, and Collate appear
grayed out and are unavailable. 
Note 
The stamp and background are not printed on blank shee ts inserted with the Insert blank page
function of booklet printing. 
Page top
Page 244 of 437 pages
Booklet Printing
JownloadedhfromhManualsPrinterDcomhManuals  
						

							Advanced Guide > Printing from a Computer > Printing with Other Application Software > Various Printing Methods >
Duplex Printing 
Duplex Printing 
The procedure for printing data on both sides of a  sheet of paper is as follows:
You can also set duplex printing in Additional Features on the Quick Setup tab. 
Performing Automatic Duplex Printing 
You can perform the duplex printing without having  to turn over the paper. 
1.Open the printer driver setup window
2.
Set automatic duplex printing  
Check the Duplex Printing check box on the Page Set up tab and confirm that Automatic is checked. 
3.Select the layout  
Select Normal-size (or Fit-to-Page, Scaled or Page Layout) from the Page Layout list. 
4.Set the print area  
W hen you perform duplex printing, the print area of the document becomes slightly narrower than
usual and the document may not fit on one page. 
Click Print Area Setup..., and select one of the fo llowing processing methods.  Page 245 of 437 pages
Duplex Printing
JownloadedhfromhManualsPrinterDcomhManuals    
						

							Use normal-size printing  
Print without reducing the page.  
Use reduced printing  
Reduce the page slightly during printing. 
5.Specify the side to be stapled  
The printer analyzes the Orientation and Page Layout settings, and automatically selects the best
Staple Side. W hen you want to change the setting, s elect another value from the list. 
6.Set the margin width  
If necessary, click Specify Margin... and set the margin w idth, and then click OK. 
7.Complete the setup  
Click OK on the Page Setup tab. 
W hen you execute print, duplex printing will be started. 
Performing Duplex Printing Manually 
You can perform the duplex printing manually. 
1.Open the printer driver setup window
2.
Set duplex printing  
Check the Duplex Printing check box and uncheck the Auto matic check box on the Page Setup tab. 
3.Select the layout  Page 246 of 437 pages
Duplex Printing
JownloadedhfromhManualsPrinterDcomhManuals   
						

							Select Normal-size (or Fit-to-Page, Scaled or Page Layout) from the Page Layout list. 
4.Specify the side to be stapled  
The printer analyzes the Orientation and Page Layou t settings, and automatically selects the best
Staple Side. W hen you want to change the setting, s elect another value from the list. 
5.Set the margin width  
If necessary, click Specify Margin... and set the margin w idth, and then click OK. 
6.Complete the setup  
Click OK on the Page Setup tab.  
W hen you execute print, the document will be printed on one side of a sheet of paper. W hen the
printing of one side is complete, load the paper co rrectly by following the message and click OK.
The document will be printed on the opposite side. 
Important 
Duplex Printing appears grayed out and is unavailab le when: 
A media type other than Plain Paper, Hagaki A or Ha gaki is selected from the Media Type list. 
Poster is selected from the Page Layout list. 
W hen Booklet is selected from the Page Layout list, Duplex Printing and Staple Side appear grayed
out and are unavailable. 
After printing the front page, there is an ink dryi ng wait time before starting to print the back page
(Operation stops temporarily). Do not touch the pap er during the time. You can change the ink
drying wait time at Custom Settings on the Maintena nce tab. 
W hen you perform the automatic duplex printing for Hagaki, print an address first and then print your
message. 
Note 
W hen you select borderless printing during duplex p rinting, a dialog box for media type selection
may appear. If that happens, select Plain Paper. 
W hen performing the automatic duplex printing, do n ot use any plain paper smaller than A5. Also,
do not select any type of paper other than Plain Pape r, Hagaki A or Hagaki at Media Type. 
If the back side of the paper becomes smudged durin g duplex printing, perform Bottom Plate
Cleaning in the Maintenance tab. 
Related Topic 
Cleaning Inside the Printer
Page top
Page 247 of 437 pages
Duplex Printing
JownloadedhfromhManualsPrinterDcomhManuals 
						

							Advanced Guide > Printing from a Computer > Printing with Other Application Software > Various Printing Methods >
Stamp/Background Printing 
Stamp/Background Printing 
This feature is unavailable when the 64-bit printer  driver is used. 
The Stamp function allows you to print a stamp text  or a bitmap over or behind document data. It also
allows you to print date, time and user name. The B ackground function allows you to print a light
illustration behind the document data.  
The procedure for performing stamp/background printing  is as follows: 
Printing a Stamp 
CONFIDENTIAL, IMPORTANT, and other stamps that  are used often in companies are pre-registered.
1.Open the printer driver setup window
2.
Click Stamp/Background... on the Page Setup tab 
The Stamp/Background dialog box opens. 
3.Select a stamp  
Check the Stamp check box, and select a desired sta mp from the list.Page 248 of 437 pages
Stamp/Background Printing
JownloadedhfromhManualsPrinterDcomhManuals    
						

							The current settings are displayed in the settings preview on the left side of the Page Setup tab. 
4.Set the stamp details  
If necessary, specify the following settings, and then click OK. 
Place stamp over text  
To print the stamp on the front of the document, check  this check box. 
Note 
The stamp is given priority because the stamp is printed over the document data in the
sections where the stamp and the document data over lap. W hen this check box is unchecked,
the stamp is printed behind the document data and may  be hidden in the overlapping sections
depending on the application used. 
Stamp first page only  
To print the stamp only on the first page, check this check box. 
Define Stamp... button 
To change the stamp text, bitmap, or position, clic k this (refer to 
Registering a Stamp). 
5.Complete the setup  
Click OK on the Page Setup tab. 
W hen you execute print, the data is printed with th e specified stamp. 
Printing a Background 
Two bitmap files are pre-registered as samples. 
1.Open the printer driver setup window
2.
Click Stamp/Background... on the Page Setup tab  
The Stamp/Background dialog box opens. 
3.Select the background  
Check the Background check box, and select a desire d background from the list.
The current settings are displayed in the settings  preview on the left side of the Page Setup tab. 
4.Set the background details  
If necessary, complete the following settings, and  then click OK. 
Background first page only  
To print the background only on the first page, check t his check box. 
Select Background... button  
To use another background or change the layout or d ensity of a background, click this (refer to 
Registering Image Data to be Used as a Background). 
5.Complete the setup  
Click OK on the Page Setup tab. 
W hen you execute print, the data is printed with the specified background. 
Important 
W hen Borderless is selected, the Stamp/Background.. . button appears grayed out and is
unavailable. 
Note 
The stamp and background are not printed on blank shee ts inserted with the Insert blank pagePage 249 of 437 pages
Stamp/Background Printing
JownloadedhfromhManualsPrinterDcomhManuals 
						

							function of booklet printing. 
Related Topics 
Registering a Stamp
Registering Image Data to be Used as a Background
Page top
Page 250 of 437 pages
Stamp/Background Printing
JownloadedhfromhManualsPrinterDcomhManuals