Canon Lbp 3300 User Guide

							6-16
Optional Accessories
6
Paper Feeder
3When installing the printer unit on the paper feeder, gently set 
it down so that each surface of the printer unit is flush with 
the front or side surfaces of the paper feeder.
Also, match the positioning pins (A) and connector (B) when setting the printer 
unit.
IMPORTANT
If the printer unit cannot be placed on the paper feeder properly, lift the printer unit 
once, hold it horizontally, and place it again. If you try to set the printer unit 
forcefully without lifting it, the connector and positioning pins may be broken.
4Set the paper cassette in the printer unit and paper feeder.
5Open the expansion slot cover.
6Connect the interface cables except for the USB cable, and 
connect the power cord.
7Plug the power plug into the AC power outlet.
(A)
(A)
(B)
 
						

							6-17
Optional Accessories
6
Paper Feeder
8Connect the USB cable, then close the expansion slot cover.
IMPORTANT
Be sure to turn the printer ON once when loading paper in the paper cassette for 
the first time after installing the paper feeder.
NOTE
After installing the paper feeder, you have to specify the settings for the optional 
accessories in the [Configuration]/[Device Settings] sheet in the printer driver. You 
can obtain the status of the optional accessories automatically by clicking [Get 
Device Status] in the [Configuration]/[Device Settings] sheet.
 
Removing the Paper Feeder
Remove the paper feeder using the following procedure.
WARNING
Be sure to turn the printer and computer OFF, unplug the power plug, and then 
disconnect all the interface cables and power cord from the printer before 
removing the paper feeder. Otherwise, the power cord or interface cables may 
be damaged, resulting in a fire or electrical shock.
CAUTION
•Do not carry the printer with the paper cassette attached. If you do so, the paper 
cassette may drop resulting in personal injury.
•Do not carry the printer with the paper feeder installed. If you do so, the paper 
feeder may drop resulting in personal injury.
 
IMPORTANT
When moving or servicing the printer, remove the paper feeder and paper cassette.
 
						

							6-18
Optional Accessories
6
Paper Feeder
1Open the expansion slot cover.
2Turn the printer and computer OFF, remove the USB cable, 
and then disconnect the power plug from the AC power outlet.
3Remove all the interface cables and the power cord from the 
printer.
4Close the expansion slot cover.
5Pull out the paper cassette from the printer unit and all the 
paper feeder.
6Lift the printer unit and remove it from the paper feeder.
7Move the paper feeder.
8Move back the printer unit to the installation site.
9Set the paper cassette in the printer.
10Open the expansion slot cover.
11Connect the interface cables except for the USB cable, and 
connect the power cord.
12Plug the power plug into the AC power outlet.
13Connect the USB cable, then close the expansion slot cover.
 
						

							6-19Network Board
6
Optional Accessories
Network Board
Install the network board in the expansion slot located on the rear of the printer.
By installing the optional network board, you can use LBP3300 directly connected 
to a network.
ERR LNK 100NB-C1
Network board (NB-C1) Screws (2 pieces)Guide booklet Ferrite core
Print server 
(Windows 98/Me/2000/XP/Server 2003)
Client 
(Windows 98/Me/2000/XP/Server 2003)
Client 
(Windows 98/Me/2000/XP/Server 2003)
Client 
(Windows 98/Me/2000/XP/Server 2003)Client 
(Windows 98/Me/2000/XP/Server 2003)
• Connecting the network board on the printer directly to the computer
• Connecting the printer to the computer via a print server
LBP3300 
(Network board installed)
LBP3300 
(Network board installed)
* If your print server is Windows 98/Me, you cannot download 
and install the driver on Windows 2000/XP/Server 2003.
: TCP/IP
: TCP/IP
: 
Usable Protocols
 
						

							6-20
Optional Accessories
6
Network Board
CAUTION
•Be sure to turn the printer OFF, unplug the power plug, and then disconnect all 
the interface cables and power cord from the printer before installing the 
network board. If a USB cable is connected, turn the computer off, and then 
remove the USB cable. If you attempt to remove the network board when the 
printer is ON or any cable is connected to the printer, this may result in an 
electrical shock.
•Be careful when handling the network board. Touching the edges or a sharp 
portion of the network board may result in personal injury.
IMPORTANT
The network board contains components that are sensitive to static electricity. Observe 
the following precautions when handling the network board to prevent damage from 
static electricity.
- Touch a metal object to dissipate static electricity before handling the network board.
- When handling the network board, do not touch anything that generates static 
electricity such as the computer display.
- Do not touch the network board parts, printed wire, or connectors with your hands.
- To prevent the network board from being affected by static electricity, keep it in the 
protective bag until it is ready to be installed. The protective bag is required after the 
network board is removed. Keep the protective bag and do not discard of it.
NOTE
This network board does not come with a LAN cable. A Category 5 twisted pair cable is 
required for installing the network board and connecting the printer to a network. Have 
cables or a hub ready as needed.
 
						

							6-21
Optional Accessories
6
Network Board
 
Parts and Their Functions
aa a a
Printer Connector
Connects to the printer. Do not touch the connector 
directly with your hands.
bb b b
LAN Connector
Connects to a 10BASE-T/100BASE-TX LAN cable.
cc c c
100 Indicator (Green)
Comes on when the network board is connected to 
the network by 100BASE-TX.
Does not come on when connected by 10BASE-T.
dd d d
LNK Indicator (Green)
Comes on when the network board is connected to 
the network properly.
ee e e
ERR Indicator (Orange)
Comes on or blinks when the network board is not 
working properly.
ff f f
MAC Address
It is required when setting the IP address using the 
ARP/PING command. It may be also required when 
installing the printer driver.
 
Installing the Network Board
Install the network board in the expansion slot of the printer using the following 
procedure. A Phillips screwdriver is required for installing the network board. Have 
a screwdriver ready in advance that matches the size of the screws.
1Open the expansion slot cover.
ERR LNK 100NB-C1
ERR LNK 100NB-C1
a
cb
de
f
 
						

							 
6-22 
Optional Accessories
 
6 
Network Board 
2
 
Turn the printer and computer OFF  
a 
, remove the USB cable  
b 
, and then disconnect the power plug from the AC power 
outlet  
c 
. 
3
 
Remove the power cord. 
If there is not enough space to install the network board, move the printer to a 
place where you can work easier. 
4
 
Remove the screws and remove the protective plate for the 
expansion slot.
a
a
c
b
 
						

							6-23
Optional Accessories
6
Network Board
IMPORTANT
The removed protective plate and screws are required when the network board is 
removed. Keep them where they will not get lost.
5Insert the network board into the expansion slot.
Hold the metal panel portions of the network board and insert the board while 
aligning it with the guide rails inside the expansion slot.
IMPORTANT
•Do not touch the network board parts, printed wire, or connectors with your hands.
•Insert the printer connector of the network board securely into the connector inside 
the expansion slot.
6Secure the top and bottom portions of the network board with 
the two screws supplied with the network board.
 
						

							6-24
Optional Accessories
6
Network Board
7Attach the ferrite core to the LAN cable as shown in the figure.
Attach the ferrite core at 5 cm or less from the end of the connector which is 
connected to the printer.
NOTE
This network board does not come with a LAN cable. A Category 5 twisted pair 
cable is required for installing the network board and connecting the printer to a 
network. Have cables or a hub ready as needed.
8Connect the LAN cable.
Connect a LAN cable that is compatible with the LAN connector of the network 
board according to the network.
9Connect the power cord.
10Plug the power plug into the AC power outlet.
5 cm or less
 
						

							6-25
Optional Accessories
6
Network Board
11Connect the USB cable as needed.
12Press   of the power switch to turn the printer ON.
IMPORTANT
If the printer does not operate properly, or an error message appears in the Printer 
Status Window, see Troubleshooting, on p. 7-1.
13Make sure that the LNK indicator (green) on the network 
board is on.
If the network board is connected by 10BASE-T, the board is working properly 
when the LNK indicator is on.
If the network board is connected by 100BASE-TX, the board is working properly 
when the LNK indicator and 100 indicator are on.
((A): ERR Indicator (B): LNK Indicator (C): 100 Indicator)
If the network board is not working properly, turn the printer OFF, and then check 
the LAN cable connection, hub performance, and network board installation.
(A)
(B)
(C)