Yamaha Dvx 1000 Owners Manual
Have a look at the manual Yamaha Dvx 1000 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 255 Yamaha manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Dynamics Parameters331 DM1000 Version 2—Owner’s Manual Appendix COMPANDER HARD (H) COMPANDER SOFT (S) The hard and soft companders combine the effects of the compressor, expander and limiter. The companders function differently at the following levels: 1 0 dB and higher .................................... Functions as a limiter. 2 Exceeding the threshold....................... Functions as a compressor. 3 Below the threshold and width ........... Functions as an expander. The hard compander has an expansion ratio of 5:1, while the soft compander has an expan- sion ratio of 1.5:1. The expander is essentially turned off when the width is set to maximum. The compressor has a fixed knee setting of 2. *The gain is automatically adjusted according to the ratio and threshold values, and can be increased by up to 18 dB. *The OUT GAIN parameter enables you to compensate for the overall level change caused by the compression and expansion processes. Parameter Range Description THRESHOLD (dB)–54.0 to 0.0 (541 points)This determines the level at which compression is applied. RATIO1.0:1, 1.1:1, 1.3:1, 1.5:1, 1.7:1, 2.0:1, 2.5:1, 3.0:1, 3.5:1, 4.0:1, 5.0:1, 6.0:1, 8.0:1, 10:1, 20:1, (15 points)This determines the amount of compression. ATTACK (ms)0–120 (121 points)This determines how soon the signal is com- pressed or expanded once the compander has been triggered. RELEASE (ms)44.1kHz: 6 ms – 46.0 sec 48kHz: 5 ms – 42.3 sec 88.2kHz: 3 ms – 23.0 sec 96kHz: 3 ms – 21.1 sec (160 points)This determines how soon the compressor or expander returns to the normal gain once the trigger signal level drops below or exceeds the threshold respectively. The value is expressed as the duration required for the level to change by 6 dB. OUT GAIN (dB)–18.0 to 0.0 (180 points) This sets the companders output signal level. WIDTH (dB)0–90 (91 points)This determines how far below the threshold expansion will be applied. The expander is acti- vated when the level drops below the threshold and width. 0dBInput Level Output Level THRESHOLD WIDTH
332Appendix B: Specifications DM1000 Version 2—Owner’s Manual Appendix B: Specifications General Spec Number of scene memories 99 Sampling FrequencyInternal 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz ExternalNormal rate: 44.1 kHz–10% to 48 kHz+6% Double rate: 88.2 kHz–10% to 96 kHz+6% Signal Delayfs=48 kHz Less than 1.6 ms CH INPUT to OMNI OUT fs=96 kHz Less than 0.8 ms CH INPUT to OMNI OUT Fader 100 mm motorized with touch sense × 17 Fader Resolution+10 to –138, –∞ dB input faders 0 to –138, –∞ dB master faders, stereo fader Total Harmonic Distortion 1 (CH INPUT to OMNI OUT) (Input Gain=Min.)fs=48 kHzLess than 0.05% 20 Hz to 20 kHz @ +14 dB into 600 Ω Less than 0.01% 1 kHz @ +24 dB into 600 Ω fs=96 kHzLess than 0.05% 20 Hz to 40 kHz @ +14 dB into 600 Ω Less than 0.01% 1 kHz @ +24 dB into 600 Ω Frequency Response (CH INPUT to OMNI OUT)fs=48 kHz 20 Hz–20 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω fs=96 kHz 20 Hz–40 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω Dynamic Range (maximum level to noise level)110 dB typ. DA Converter (OMNI OUT) 106 dB typ. AD+DA (to OMNI OUT) @ fs=48 kHz 106 dB typ. AD+DA (to OMNI OUT) @ fs=96 kHz Hum & Noise 2 (20 Hz–20 kHz) Rs=150 Ω–128 dB Equivalent Input Noise –86 dB residual output noise. OMNI OUT (STEREO OUT off) Input Gain=Max. Input Pad =0 dB–86 dB (90 dB S/N) OMNI OUT (STEREO fader at nominal level and all CH INPUT faders at minimum level) Input Pad =0 dB Input Sensitivity =–60 dB–64 dB (68 dB S/N) OMNI OUT (STEREO fader at nominal level and one CH INPUT fader at nominal level) Maximum Voltage Gain 74 dB CH INPUT (CH1–16) to OMNI OUT (STEREO, BUS, AUX) Crosstalk (@ 1 kHz) Input Gain=Min. 80 dB adjacent input channels (CH1–16) 80 dB input to output AD Input (1–16)Phantom switch +48 V DC Pad switch 0/20 dB attenuation Gain control 44 dB (–60 to –16), detented Peak indicatorLED (red) turns on when post HA level reaches 3 dB below clipping at dig- ital domain Signal indicatorLED (green) turns on when post HA level reaches 20 dB below nominal at digital domain AD converter24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over- sampling (fs=88.2, 96 kHz) Analog Input (OMNI IN 1–4)AD converter24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over- sampling (fs=88.2, 96 kHz) Option Input (SLOT 1–2) Available cards Optional digital interface cards (MY16, MY8, MY4 series) Digital Input (2TR IN DIGITAL 1–2)SRC On/off (1:3 and 3:1 maximum input to output sample rate ratio)
General Spec333 DM1000 Version 2—Owner’s Manual Appendix Input Channel CH1–48Input patch — Phase Normal/reverse Gate-type 3On/off Key in: 12 ch Group (1–12, 13–24, 25–36, 37–48)/AUX1–8 Comp-type 4On/off Key in: self /Stereo Link Pre EQ/pre fader/post fader Attenuator –96.0 to +12.0 dB (0.1 dB step) EQ4-band PEQ (TYPE1) 5 On/off Delay 0–43400 samples On/off — Fader 100 mm motorized (INPUT/AUX1–8) Aux sendOn/off AUX1–8; pre fader/post fader SoloOn/off Pre fader/after pan Pan 127 positions (Left= 1–63, Center, Right= 1–63) Surround pan127 × 127 positions [(Left= 1–63, Center, Right= 1–63)] x [(Front= 1–63, Center, Rear= 1–63)] LFE level –∞, –96 dB to +10 dB (256 step) Routing STEREO, BUS1–8, DIRECT OUT Direct out Pre EQ/pre fader/post fader MeteringDisplayed on LCD Peak hold on/off TALKBACKLevel control Analog rotary potentiometer AD converter24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times over- sampling (@fs=88.2, 96 kHz) Talkback select Built-in microphone/AD IN 1–16/OMNI IN 1–4 On/off — OSCILLATORLevel 0 to –96 dB (1 dB step) On/off — Waveform Sine 100 Hz, sine 1 kHz, sine 10 kHz, 400 Hz/1 kHz, pink noise, burst noise Routing BUS1–8, AUX1–8, STEREO L, R OMNI OUT 1–12Output patchSTEREO, BUS1–8, AUX1–8, SURROUND MONITOR, CONTROL ROOM, DIRECT OUT 1–48, INSERT OUT (CH1–48, BUS1–8, AUX1–8, STEREO), MONITOR MATRIX OUT, SOLO OUT, CASCADE OUT (BUS1–8, AUX 1–8, STEREO, SOLO) DA converter24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times over- sampling (@fs=88.2, 96 kHz) 2TR OUT DIGITAL 1–2DitherOn/off Word length 16, 20, 24-bit Output patchSTEREO, BUS1–8, AUX 1–8, CONTROL ROOM, DIRECT OUT 1–48, INSERT OUT (CH 1–48, BUS 1–8, AUX 1–8, STEREO), SOLO OUT, CASCADE OUT (BUS 1–8, AUX 1–8, STEREO, SOLO) Option Output (SLOT 1–2)Available card Optional digital interface card (MY16, MY8, MY4 series) Output patchSTEREO, BUS1–8, AUX 1–8, SURROUND MONITOR, CONTROL ROOM, DIRECT OUT 1–48, INSERT OUT (CH 1–48, BUS 1–8, AUX 1–8, STEREO), MONITOR MATRIX OUT, SOLO OUT, CASCADE OUT (BUS 1–8, AUX 1–8, STEREO, SOLO) DitherOn/off Word length 16/20/24-bit
334Appendix B: Specifications DM1000 Version 2—Owner’s Manual STEREOComp-type 4On/off Pre EQ/pre fader/post fader Attenuator –96.0 to +12.0 dB (0.1 dB step) EQ4-band PEQ 5 On/off On/off — Fader 100 mm motorized Balance 127 positions (Left=1–63, Center, Right=1–63) Delay 0–29100 samples MeteringDisplayed on LCD Peak hold on/off 32-elements x2 LED meters BUS1–8Comp-type 4On/off Pre EQ/pre fader/post fader Attenuator –96.0 to +12.0 dB (0.1 dB step) EQ4-band PEQ 5 On/off On/off — Fader 100 mm motorized Delay 0–29100 samples Bus to stereoLevel (–∞, –138 dB to 0 dB) On/off Pan: 127 positions (Left=1–63, Center, Right=1–63) MeteringDisplayed on LCD Peak hold on/off AUX1–8Comp-type 4On/off Pre EQ/pre fader/post fader Attenuator –96.0 to +12.0 dB (0.1 dB step) EQ4-band PEQ 5 On/off On/off — Fader 100 mm motorized Delay 0–29100 samples MeteringDisplayed on LCD Peak hold on/off SURROUND MONITORMute On/off Solo On/off Source BUS1–8, SLOT 1–2 Monitor to C-R On/off Oscillator Pink noise/500–2 kHz/1 kHz Monitor matrix6.1→6.1, 6.1→5.1, 6.1→3-1, 6.1→ST, 5.1→5.1, 5.1→3-1, 5.1→ST, 3-1→3-1, 3-1→ST Bass management5 presets Monitor alignmentATT (–12.0 dB to 12 dB 0.1 dB step), Delay (0–30.0 msec 0.02 msec step) INTERNAL EFFECTS (EFFECT 1–4)Bypass On/off In/out8-in, 8-out (EFFECT1): depends on effects type 2-in, 2-out (EFFECT2–4): depends on effects type Effect-in from AUX1–8/INSERT OUT/effect-out (out 1, 2 only) Effect-out 1, 2 to Input patch/effect-in
General Spec335 DM1000 Version 2—Owner’s Manual Appendix EQ Parameters Gate Parameters Power RequirementsU.S./Canada 120 V, 60 Hz 135 W Other 220–240 V, 50/60 Hz 135 W Dimensions (H x D x W)200 x 585 x 436 mm (7.8 x 23.0 x 17.1) With MB1000 and SP1000 installed: 295 x 635 x 486 mm (11.6 x 25.0 x 19.1) Net weight 20 kg (75 lbs) Operating free-air temperature range 10–35°C (50–95°F) Storage temperature range –20 to 60°C (–4 to 140°F) Supplied AccessoriesAC Cable, CD-ROM (Studio Manager), Owner’s Manual, Studio Manager Installation Guide OptionsDigital interface card (MY16, MY8, MY4 series) PEAK METER BRIDGE: MB1000 SIDE PANEL: SP1000 RACK MOUNT KIT: RK1 1. Total harmonic distortion is measured with a 6 dB/octave filter @ 80 kHz. 2. Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation. 3. See “Gate Parameters” on page 335. 4. See “Comp Parameters” on page 336. 5. See “EQ Parameters” on page 335. LOW/HPF L-MID H-MID HIGH /LPF Q0.1–10.0 (41 points) low shelving HPF0.1–10.0 (41 points)0.1–10.0 (41 points) high shelving LPF F 21.2 Hz–20 kHz (1/12 oct step) G±18 dB (0.1 dB step) HPF: on/off±18 dB (0.1 dB step)±18 dB (0.1 dB step) LPF: on/off GateThreshold –54 dB to 0 dB (0.1 dB step) Range –70 dB to 0 dB (1 dB step) Attack 0 ms–120 ms (1 ms step) Hold0.02 ms–1.96 s (216 points) @ 48 kHz 0.02 ms–2.13 s (216 points) @ 44.1 kHz 0.01 ms–981 ms (216 points) @ 96 kHz 0.01 ms–1.06 s (216 points) @ 88.2 kHz Decay5 ms–42.3 s (160 points) @ 48 kHz 6 ms–46.0 s (160 points) @ 44.1 kHz 3 ms–21.1 s (160 points) @ 96 kHz 3 ms–23.0 s (160 points) @ 88.2 kHz DuckingThreshold –54 dB to 0 dB (0.1 dB step) Range –70 dB to 0 dB (1 dB step) Attack 0 ms–120 ms (1 ms step) Hold0.02 ms–1.96 s (216 points) @ 48 kHz 0.02 ms–2.13 s (216 points) @ 44.1 kHz 0.01 ms–981 ms (216 points) @ 96 kHz 0.01 ms–1.06 s (216 points) @ 88.2 kHz Decay5 ms–42.3 s (160 points) @ 48 kHz 6 ms–46.0 s (160 points) @ 44.1 kHz 3 ms–21.1 s (160 points) @ 96 kHz 3 ms–23.0 s (160 points) @ 88.2 kHz
336Appendix B: Specifications DM1000 Version 2—Owner’s Manual Comp Parameters CompressorThreshold –54 dB to 0 dB (0.1 dB step) Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, ∞ (16 points) Out gain 0 dB to +18 dB (0.1 dB step) Knee Hard, 1, 2, 3, 4, 5 (6 step) Attack 0 ms–120 ms (1 ms step) Release5 ms–42.3 s (160 points) @ 48 kHz 6 ms–46.0 s (160 points) @ 44.1 kHz 3 ms–21.1 s (160 points) @ 96 kHz 3 ms–23.0 s (160 points) @ 88.2 kHz ExpanderThreshold –54 dB to 0 dB (0.1 dB step) Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, ∞ (16 points) Out gain 0 dB to +18 dB (0.1 dB step) Knee Hard, 1, 2, 3, 4, 5 (6 points) Attack 0 ms–120 ms (1 ms step) Release5 ms–42.3 s (160 points) @ 48 kHz 6 ms–46.0 s (160 points) @ 44.1 kHz 3 ms–21.1 s (160 points) @ 96 kHz 3 ms–23.0 s (160 points) @ 88.2 kHz Compander HThreshold –54 dB to 0 dB (0.1 dB step) Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points) Out gain –18 dB to 0 dB (0.1 dB step) Width 1 dB–90 dB (1 dB step) Attack 0 ms–120 ms (1 ms step) Release5 ms–42.3 s (160 points) @ 48 kHz 6 ms–46.0 s (160 points) @ 44.1 kHz 3 ms–21.1 s (160 points) @ 96 kHz 3 ms–23.0 s (160 points) @ 88.2 kHz Compander SThreshold –54 dB to 0 dB (0.1 dB step) Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points) Out gain –18 dB to 0 dB (0.1 dB step) Width 1 dB–90 dB (1 dB step) Attack 0 ms–120 ms (1 ms step) Release5 ms–42.3 s (160 points) @ 48 kHz 6 ms–46.0 s (160 points) @ 44.1 kHz 3 ms–21.1 s (160 points) @ 96 kHz 3 ms–23.0 s (160 points) @ 88.2 kHz
Libraries 337 DM1000 Version 2—Owner’s Manual Appendix Libraries Analog Input Spec In these specifications, when dB represents a specific voltage, 0 dB is \ referenced to 0.775 Vrms. All input AD converters (INPUT 1–16, OMNI INPUT 1–4, TALKBACK) a\ re 24-bit linear, 128-times oversampling. (@fs=44.1, 48 kHz) +48 V DC (phantom power) is supplied to CH INPUT (1–16) XLR type \ connectors via individual switches. Analog Output Spec In these specifications, when dB represents a specific voltage, 0 dB is \ referenced to 0.775 Vrms. All output DA converters (OMINI OUT 1–12, PHONES) are 24-bit, 128-t\ imes oversampling. (@fs=44.1, 48 kHz) Effect library (EFFECT 1–4) Presets 61 (EFFECT 2–4: 53) User memories 67 Compressor library Presets 36 User memories 92 Gate library Presets 4 User memories 124 EQ library Presets 40 User memories 160 Channel library Presets 2 User memories 127 Surround Monitor library Presets 1 User memories 32 Input patch library Presets 1 User memories 32 Output patch library Presets 1 User memories 32 Bus to Stereo library Presets 1 User memories 32 Input PAD GAIN Actual Load Impedance For Use With Nominal Input level Connector Sensitivity 1 1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are maximum posi\ tion.) NominalMax. before clip INPUT 1–16 0–60 dB 3k Ω 50–600 Ω Mics & 600 Ω Lines –70 dB (0.245 mV) –60 dB (0.775 mV) –40 dB (7.75 mV) XLR-3-31 type (Balanced) 2 2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD). –16 dB –26 dB (38.8 mV) –16 dB (0.123 V) +4 dB (1.23 V) 20 –6 dB (388 mV) +4 dB (1.23 V) +24 dB (12.28 V) OMNI IN 1–4 —10k Ω 600 Ω Lines+4 dB (1.23 V) +4 dB (1.23 V) +24 dB (12.28 V) Output Actual Source Impedance For Use With Nominal Output level Connector Nominal Max. before clip OMNI OUT 1–12 75 Ω 600 Ω Lines+4 dB (1.23 V) +24 dB (12.28 V) XLR-3-32 type (Balanced) 1 1. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD). PHONES 100 Ω 8 Ω Phones 4 mW 25 mWStereo Phone Jack (TRS) (Unbalanced) 2 2. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GN\ D). 40 Ω Phones12 mW 75 mW
338Appendix B: Specifications DM1000 Version 2—Owner’s Manual Digital Input Spec Digital Output Spec Input Format Data length Level Connector 2TR IN DIGITAL1 AES/EBU 24-bit RS422 XLR-3-31 type (Balanced) 1 1. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).2 IEC-60958 24-bit 0.5 Vpp/75 ΩPhono Output Format Data length Level Connector 2TR OUT DIGITAL1AES/EBU 1 Professional use 1. Channel status of 2TR OUT DIGITAL 1 Type: linear PCM Emphasis: NO Sampling rate: depends on the internal configuration24-bit2 2. Dither: word length 16/20/24 bitRS422XLR-3-32 type (Balanced) 3 3. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD).2IEC-60958 4 Consumer use 4. Channel status of 2TR OUT DIGITAL 2 Type: linear PCM Category code: Digital signal mixer Copy prohibit: NO Emphasis: NO Clock accuracy: Level II (1000 ppm) Sampling rate: depends on the internal configuration24-bit20.5V pp/75 ΩPhono
I/O Slot Spec (1–2)339 DM1000 Version 2—Owner’s Manual Appendix I/O Slot Spec (1–2) Each I/O SLOT accepts a digital interface card. SLOT #1 has a serial interface. Control I/O Spec Maker Model Function INPUTOUTPUT 1 1. Selectable from STEREO/BUS/AUX/DIRECT/EXT INSERT/SURROUND MONITOR/CR MON\ ITOR. Details depend on each interface card. Format Resolution Frequency The number of Avai lable cards Note Y amaha MY8-AT Digital I/O 88 ADAT 24 bit44.1/48 kHz 2Can handle 24 bit/96 kHz by double channel mode MY16-AT 16 16 MY8-TD 8 8 TASCAM MY16-TD 16 16 MY8-AE 8 8 AES/EBU MY16-AE 16 16 MY8-AEB 88 MY8-AE96S 44.1/48/88.2/96 kHzSampling Rate Con- verter for input MY8-AE96 MY4-AD ANALOG IN 4 — —24 bit 44.1/48 kHz 2 MY8-AD 820 bit MY8-AD24 24 bit MY8-AD96 44.1/48/88.2/96 kHz MY4-DA ANALOG OUT — 4 20 bit 44.1/48 kHz MY8-DA96 8 24 bit 44.1/48/88.2/96 kHz MY8- ADDA96 ANALOG I/O 8 8 MY8-mLAN mLAN Interface 88 IEEE1394 24 bit 44.1/48 kHz Maximum 5 nodes MY16- mLAN 16 16 W aves Y56K Effect & I/O 8 8 ADAT 24 bit 44.1/48 kHz 1 Y96K 44.1/48/88.2/96 kHz 2 Apogee AP8AD ANALOG IN 8 — —24 bit 44.1/48/88.2/96 kHz 2 4ch @fs=88.2, 96 kHz AP8DA ANALOG OUT — 8 I/O Port Format Level Connector in Console TO HOST USB USB 0 V–3.3 V B type USB connector MIDI IN 1 1. MIDI IN can use as TIME CODE IN MTC. MIDI — DIN Connector 5P OUT MIDI — DIN Connector 5P TIME CODE INPUT SMPTE Nominal –10 dB/10k Ω XLR-3-31 type (Balanced) 2 2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD). WORD CLOCK IN — TTL/75 Ω BNC Connector OUT — TTL/75 Ω BNC Connector CONTROL —C-MOS IN, Open collector OUT 1pin: 150 mA, 8pin total: 500 mA D-SUB Connector 25P (Female) REMOTE —RS422 D-SUB Connector 9P (Male) METER —RS422 D-SUB Connector 15P (Female)
340Appendix B: Specifications DM1000 Version 2—Owner’s Manual REMOTE Port CONTROL Port Pin Signal Pin Signal1 GND 6 RX+/GND 1 2RX–/RX–1 1. RS422 (for AD8HR, AD824)/SONY 9 pin pro- tocol (P2), ESAM II 7 RTS/RX+ 1 3 TX–/TX+18CTS/TX–1 4 TX+/GND19GND 5 N.C. Pin Signal Pin Signal 1 GPO0 14 GPO1 2 GPO2 15 GPO3 3 GPO4 16 GPO5 4 GPO6 17 GPO7 5 GND 18 GND 6 GND 19 GND 7 GND 20 GND 8 GND 21 +5V 9 +5V 22 GPI0 10 GPI1 23 GPI2 11 GPI3 24 N.C. 12 N.C. 25 N.C. 13 N.C.