Yamaha Dvx 1000 Owners Manual

							Input Patching111
DM1000 Version 2—Owner’s Manual
9
Input & Output Patching
Using the Encoders for Input Patching
By default, you can also use the Encoders on the top panel to change the Input Patching.
1Press the ENCODER MODE [ASSIGN] button. The button indicator lights up.
By default, you can use the Encoders to change Input Patching while the [ASSIGN] button 
indicator is lit.
2Rotate the Encoder of the Input Channel for which you want to change 
patching. (Alternatively, press the corresponding Encoder push switch.)
The In Patch | In Patch page appears, and the cursor moves to the corresponding Input 
Channel parameter box.
3Rotate the Encoder to select the desired input/slot channel number you 
want to patch.
4Press the Encoder push switch to confirm the setting (or press the [ENTER] 
button).Tip:  On the Encoder page, you can specify the Encoder function that works while the 
[ASSIGN] button indicator is lit (see page 37).
 
						

							112Chapter 9—Input & Output Patching
DM1000 Version 2—Owner’s Manual
Output Patching
The DM1000’s Stereo Out, Bus Out 1–8, Aux Out 1–8 signals can be patched to any outputs 
and slot channels.
Patch example:
By default, the following signal paths are patched to outputs and slot output channels:
You can change these patches, if you desire. The procedure for patching signals to output 
varies depending on the output connectors and slots.
Output connectors and slot 
channelsSignal flow
OMNI OUT connectors 1–8
Aux Outs 1–8
OMNI OUT connectors 9–10
Stereo Out L & R
OMNI OUT connectors 11–12
Control Room Monitor L & R
Channels 1–8 of Slot 1
Bus Outs 1–8
Channels 9–16 of Slot 1
Bus Outs 1–8
Channels 1–8 of Slot 2
Bus Outs 1–8
Channels 9–16 of Slot 2
Bus Outs 1–8
2TR OUT DIGITAL 1 (L)
Stereo Out L
2TR OUT DIGITAL 1 (R)
Stereo Out R
2TR OUT DIGITAL 2 (L)
Stereo Out L
2TR OUT DIGITAL 2 (R)
Stereo Out R
Tip:  
•You can patch a signal to multiple outputs and slot channels.
•You can store the Output Patch settings to the Output Patch library. Refer to Chapter 15 
“Libraries” on page 173 for more information.
Output Patching
Stereo Out L
Stereo Out R
Aux Out 1
Aux Out 2
Aux Out 3
Aux Out 4
Aux Out 5
Aux Out 6OMNI Out connector 1
OMNI Out connector 2
OMNI Out connector 3
OMNI Out connector 4
OMNI Out connector 5
OMNI Out connector 6
OMNI Out connector 7
OMNI Out connector 8
 
						

							Output Patching113
DM1000 Version 2—Owner’s Manual
9
Input & Output Patching
Patching Omni Outs
You can route the DM1000’s internal signals to OMNI OUT 1–12.
1Press the DISPLAY ACCESS [OUTPUT PATCH] button repeatedly until the Out 
Patch | Omni Out page appears.
The OMNI 1–12 parameter boxes (
1) indicate the currently-patched signals. The param-
eter indicators are explained below:
2Move the cursor to a patch parameter you wish to change, and rotate the 
Parameter wheel or press the [INC]/[DEC] buttons to modify the patching.
3Press [ENTER] to confirm the change.
Parameter values Description
–
No assignment
BUS1–BUS8
Bus Out 1–8 signal
AUX1–AUX8
Aux Out 1–8 signal
ST L/R
Stereo Out signal
INS CH1–INS CH48
Input Channel 1–48 Insert Out
INS BUS1–INS BUS8
Bus Out 1–8 Insert Out
INS AUX1–INS AUX8
Aux Out 1–8 Insert Out
INS ST-L/ST-R
Stereo Out Insert Out
SURR XXX
(“XXX” represents a channel name.)Surround Monitor Outs
CR-L/CR-R
Control Room Monitor signals
CAS BUS1–BUS8
Bus 1–8 Cascade Outs
CAS AUX1–AUX8
Aux Bus 1–8 Cascade Outs
CAS ST-L/ST-R
Stereo Bus Cascade Outs
CASSOLOL/CASSOLOR
Solo Bus Cascade Outs
SOLO-L/SOLO-R
Solo Bus signal
M.MX XXX
(“XXX” represents a channel name.)Output signals from the surround monitor 
monitor matrix
Tip:  You can store the Output Patch settings to the Output Patch library. Refer to Chapter 15 
“Libraries” on page 173 for more information.
1
 
						

							114Chapter 9—Input & Output Patching
DM1000 Version 2—Owner’s Manual
Patching the 2TR Digital Outputs
You can route the DM1000’s internal signals to 2TR OUT DIGITAL connectors 1–2.
1Press the DISPLAY ACCESS [OUTPUT PATCH] button repeatedly until the Out 
Patch | 2TR Out page appears.
Signals assigned on the Omni Out page can also be assigned to the 2TR digital outputs.
2Move the cursor to a patch parameter you wish to change, and rotate the 
Parameter wheel or press the [INC]/[DEC] buttons to modify the patching.
3Press [ENTER] to confirm the change.
Patching Slot Outputs
You can route the DM1000’s internal signals to optional mini-YGDAI cards installed in Slot 
1 and 2.
1Press the DISPLAY ACCESS [OUTPUT PATCH] button repeatedly until the Out 
Patch | Slot Out page appears.
Signals assigned on the Omni Out page can also be assigned to the slot outputs. However, 
you cannot assign SURR. XXX and M.MX XXX.
2Move the cursor to a patch parameter you wish to change, and rotate the 
Parameter wheel or press the [INC]/[DEC] buttons to modify the patching.
3Press [ENTER] to confirm the change.
 
						

							Patching Direct Outs115
DM1000 Version 2—Owner’s Manual
9
Input & Output Patching
Patching Direct Outs
Input Channel 1–48 signals can be directly patched to any outputs or slot outputs, as well 
as Bus Out 1–8 and Stereo Out. This patching is convenient when you wish to record each 
Input Channel signal to an individual track on a connected recorder.
1Press the DISPLAY ACCESS [OUTPUT PATCH] button repeatedly until the Out 
Patch | Direct Out page appears.
The parameters on this page are described below.
A1–48
These boxes indicate the Direct Out destination (outputs and slot channels) for Input 
Channels 1–48.
BDIRECT OUT
Determines the Direct Out signal source position from the following three options:
•PRE EQ.......................... Immediately before Input Channel EQ
•PRE FADER.................. Immediately before Input Channel fader
•POST FADER............... Immediately after Input Channel fader
2Move the cursor to a patch parameter (1–48) you wish to change, and rotate 
the Parameter wheel or press the [INC]/[DEC] buttons to select the destina-
tion.
If necessary, specify the signal source position using the DIRECT OUT parameter.
3Press [ENTER] to confirm the change.
4Press the [SEL] button or move the fader of the Input Channel that is patched 
to the Direct Out assigned in Steps 2 and 3.
5Press the SELECTED CHANNEL ROUTING [DIRECT] button.
The Direct Out patching is now effective, and the signals are routed to the assigned outputs 
or slot channels.Note:  If you select a destination that is already used by an Output Patch setting and turn on 
the ROUTING [DIRECT] button, the Output Patch setting will be disabled. To restore the 
Output Patch setting, select another DIRECT OUT destination or turn off the ROUTING 
[DIRECT] button.
Tip:  Press the SELECTED CHANNEL ROUTING [DISPLAY] button repeatedly to display 
the Routing page. On this page, you can simultaneously route multiple Input Channels to 
Direct Outs.
1
2
 
						

							116Chapter 9—Input & Output Patching
DM1000 Version 2—Owner’s Manual
Insert Patching
The DM1000’s Input Channels and Output Channels (Stereo Out, Bus Out 1–8, Aux Out 
1–8) feature independent Insert Ins and Outs. Inputs, outputs, slot channels, and internal 
effects processor inputs and outputs can be patched to the Output Channel Insert Ins and 
Outs. In this way, you can send the signals to external effects processors for processing, or 
insert internal effects.
Individual Insert Patching
You can patch the DM1000’s inputs, outputs, slot channels, and effects processor inputs and 
outputs to the Insert Ins and Outs. The same procedure applies to both Input Channels and 
Output Channels.
1Press the [SEL] button or move the fader of an Input Channel or Output 
Channel for Insert patching.
2Press the [ /INSERT/DELAY] button repeatedly until the  /INS/DLY | Insert 
page appears.
This page contains the following parameters:
APOSITION
This parameter determines the insert position of the Insert patch or compressor. The 
insert position is indicated by highlighted COMP or INSERT buttons.
Effects
Input Output
Output connector Input connector
Insert Out Insert In
Channel
3
1
2
 
						

							Insert Patching117
DM1000 Version 2—Owner’s Manual
9
Input & Output Patching
BINSERT section
•ON/OFF......................... This button turns Insert on or off. 
•OUT............................... This parameter enables you to select outputs, slot channels, or 
internal effects inputs as the Insert Out destination.
•IN.................................... This parameter enables you to select inputs, slot channels, or 
internal effects outputs as the Insert In source.
CCOMP section
•ON/OFF......................... This button turns the compressor on or off.
•ORDER.......................... This parameter determines the order of Insert patch and com-
pressor when they are inserted at the same signal path point. 
With the “COMP → INS” setting, signals pass through the 
compressor first, then the Insert. With the “INS → COMP” set-
ting, signals pass through the Insert first, then the compressor.
3Move the cursor to the OUT parameter box, and rotate the Parameter wheel 
or press the [INC]/[DEC] buttons to select the desired outputs, slot channels, 
or internal effects inputs to be patched to Insert Out. The parameter indi-
cators are explained below:
4Press [ENTER] to confirm the change.
If you move the cursor to another parameter box or display another page before you press 
the [ENTER] button, all settings on this page will be cancelled.
5Move the cursor to the desired IN parameter box, and rotate the Parameter 
wheel or press the [INC]/[DEC] buttons to select the inputs or slot channels 
to be patched to the Insert In.
Refer to the explanation regarding the Input Patch for more information on the parameter 
values (see page 110).
6Press [ENTER] to confirm the change.
7To enable the specified Insert patch, move the cursor to the ON/OFF button 
in the INSERT section, and press [ENTER] to turn it on or off.
Parameter values Description
–
No assignment
S1-1–S116
Channels 1–16 of Slot 1
S2-1–S216
Channels 1–16 of Slot 2
OMN1–OM12
OMNI OUT connectors 1–12
2D1L & 2D1R
2TR OUT DIGITAL1 (L/R)
2D2L & 2D2R
2TR OUT DIGITAL2 (L/R)
FX1-1–FX1-8
Inputs 1–8 of Internal Effects Processor 1 
FX2-1 & FX2-2
Inputs 1 & 2 of Internal Effects Processor 2 
FX3-1 & FX3-2
Inputs 1 & 2 of Internal Effects Processor 3 
FX4-1 & FX4-2
Inputs 1 & 2 of Internal Effects Processor 4 
Tip:  Move the cursor to an empty OUT or IN parameter box and press the [ENTER] button. 
The Patch Select window appears. Rotate the Parameter wheel or press the cursor buttons to 
select an item to be patched and press [ENTER]. Then, move the cursor to the YES button and 
press [ENTER]. The selected item is now patched.
 
						

							118Chapter 9—Input & Output Patching
DM1000 Version 2—Owner’s Manual
Viewing and Changing Insert In Patch
You can view and also change the items patched to the Insert Ins of all Input Channels (or 
all Output Channels). This is useful when you wish to find out if multiple channels have the 
same patch.
1To view the Input Channels’ Insert Ins, press the [INPUT PATCH] button 
repeatedly until the In Patch | Insert In page appears.
This page displays Input Channels 1–48 Insert In Patches.
2Move the cursor to a channel patch parameter box you wish to change, then 
rotate the Parameter wheel or press the [INC]/[DEC] buttons to modify the 
patching.
3Press [ENTER] to confirm the change.
4To view the Output Channels’ Insert Ins, press the [OUTPUT PATCH] button 
repeatedly until the Out Patch | Insert In page appears.
5Move the cursor to a channel patch parameter box you wish to change, then 
rotate the Parameter wheel or press the [INC]/[DEC] buttons to modify the 
patching.
6Press [ENTER] to confirm the change.
 
						

							Control Room Monitoring119
DM1000 Version 2—Owner’s Manual
Control Room Monitoring
10
10  Control Room Monitoring
This chapter explains how to set up control room monitoring and use the Solo and Talkback 
functions on the DM1000.
Control Room Monitor
The DM1000 features the Control Room stereo signal path to feed the control room’s main 
monitors. By default, the Control Room signal source is patched to OMNI OUT connectors 
11 & 12, which can feed the Control Room signal to the control room’s monitor.
•MONITOR SELECT
As a Control Room Monitor signal, you can select one from Stereo Out output, 2TR IN 
DIGITAL 1 input, and 2TR IN DIGITAL 2 input.
If you change the parameter setting on the Monitor | C-R/TB page (see page 122), you can 
monitor the OMNI IN signal, instead of the 2TR IN DIGITAL signal, when you press the 
[2TR D1] or [2TR D2] button.
•SOLO bus
This special bus routes soloed Input Channels to the Control Room Monitor output, 
bypassing Bus 1–8 and the Stereo Bus.
•OUTPUT SOLO
This section routes soloed Output Channels (Aux Out 1–8, Bus Out 1–8) to the Control 
Room Monitor output.
•MONITOR LEVEL
Use the MONITOR [MONITOR LEVEL] control on the top panel to adjust the Control 
Room Monitor level.
•DIMM (Dimmer)
The [DIMMER] button lowers the Control Room Monitor signal by the specified amount.
•PHONES
The Control Room Monitor signal is also fed to the PHONES jack. You can set the level 
independently.Note:  Input and Output Channels cannot be solo-monitored simultaneously. The solo func-
tion for the most-recently soloed channels is enabled.
Note:  The Dimmer function is activated automatically when the Talkback or Oscillator func-
tion is active.
 
						

							120Chapter 10—Control Room Monitoring
DM1000 Version 2—Owner’s Manual
Solo Setup
For solo setup, press the MONITOR [DISPLAY] button repeatedly until the Monitor | Solo 
page appears.
This page contains the following parameters:
ASOLO
This parameter turns the Solo function on or off. By default, it is set to Enabled.
BMODE
This parameter determines how the Solo function works. There are two options. The 
setting affects only Input Channels.
•RECORDING............... In Recording Solo mode, soloed Input Channel signals are fed 
to the Solo bus and output via the Control Room Outputs. 
Other buses (Stereo bus and Bus 1–8) are unaffected by this 
mode.
•MIXDOWN.................. In Mixdown Solo mode, soloed Input Channel signals are fed 
to the Stereo bus and output via the Control Room Outputs. 
Unsoloed Input Channels are not fed to the Stereo bus while 
the Solo function is enabled.
CSEL MODE
This parameter determines how the Input Channels will be soloed when you press the 
[SOLO] button of each Channel. There are two options.
•MIX SOLO.................... In Mix Solo mode, any number of channels can be soloed 
simultaneously.
•LAST SOLO.................. In Last Solo mode, only one channel can be soloed at a time by 
pressing the [SOLO] button. The Solo function that was previ-
ously enabled for channels is automatically cancelled. Tip:  
•Recording Solo mode is convenient when you wish to monitor certain Input Channels 
while recording, since the Stereo bus and Bus 1–8 signals are unaffected
•Mixdown Solo mode is useful when you wish to mute unsoloed Input Channels and feed 
soloed Input Channel signals to the Stereo bus during mixdown.
4
7
1
5
8
9
6
32