Home > Yamaha > Home Theater System > Yamaha Dvx 1000 Owners Manual

Yamaha Dvx 1000 Owners Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Yamaha Dvx 1000 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 255 Yamaha manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Naming the Stereo Out and Bus Outs91
    DM1000 Version 2—Owner’s Manual
    7
    Bus Outs
    Naming the Stereo Out and Bus Outs
    You can change the default Bus names (BUS1, AUX4, STEREO, etc.). It may be convenient 
    to name the buses “Monitor Out” or “Effect Send,” for example, so that you can easily iden-
    tify the signal type.
    1Press the DISPLAY ACCESS [OUTPUT PATCH] button repeatedly until the Out 
    Patch | CH Name page appears.
    You can specify Short names in the center column (
    1) and Long (full) names in the right 
    column (
    2).
    When the Name Input Auto Copy check box (
    3) is on, the first four characters of a 
    newly-entered Long name are automatically copied to the Short name.
    You can reset all bus names to their default names by moving the cursor to the INITIALIZE 
    button, then pressing [ENTER].
    2Move the cursor to a name you wish to change, then press [ENTER].
    The Title Edit window appears, which enables you to edit the name.
    3Edit the name, move the cursor to the OK button, then press [ENTER].
    The new name is now effective.
    Tip:  The edited name is stored in the Output Patch library.
    12
    3
     
    						
    							92Chapter 7—Bus Outs
    DM1000 Version 2—Owner’s Manual
     
    						
    							Aux Sends93
    DM1000 Version 2—Owner’s Manual
    8
    Aux Sends
    8  Aux Sends
    This chapter describes how to control Aux Out 1–8.
    Aux Out 1–8
    The Aux Out 1–8 section mixes signals routed from the Input Channels to the correspond-
    ing Aux Sends, processes them using on-board EQ, compressor, etc., then routes them to 
    the specified internal effects processors, output connectors or I/O card connectors.
    The DM1000 features eight Aux Sends, which can be used to send signals to the internal and 
    external effects processors and monitors.
    The following diagram illustrates the Aux Out 1–8 signal flow.
    •INSERT
    •ATT (Attenuator)
    •4 BAND EQ (4-band equalizer)
    •COMP (Compressor)
    •ON (On/Off)
    •LEVEL
    •OUTPUT DELAY (Output delay)
    •METER
    These parameters are the same as the Stereo Out and Bus Out 1–8 (see page 81).
    Tip:  You can also pair adjacent odd-even Aux Sends (in this order) for stereo Aux operation.
    Note:  With the default setting, Aux Out 1–8 are patched to OMNI OUT connectors 1–8 and 
    Aux Out 1–4 are patched to internal effects processors 1–4. However, you can change this 
    patching on the Out Patch page.
    OUTPUT PATCH
    OUTPUT
    DELAY
    METER
    AT T4BAND
    EQ
    INSERTINSERTLEVELON
    COMP
    METER(Gain Reduction)
    INSERTMETER
    METER(Out Meter)
    TO INPUT PATCHAUX 1(...8) AUX 1(...8)
    AUX 1
    AUX 8
     
    						
    							94Chapter 8—Aux Sends
    DM1000 Version 2—Owner’s Manual
    Setting Aux Out 1–8 from the Control Surface
    You can use the faders, Encoders, [SEL] buttons, and various buttons and controls in the 
    SELECTED CHANNEL section on the top panel to directly control certain parameters for 
    Aux Out 1–8.
    Setting Levels
    To set Aux Out 1–8 levels, press the [MASTER] button in the LAYER section to select the 
    Master layer, then move faders 1–8. At this time, you can turn Aux Out 1–8 on or off using 
    the corresponding [ON] 1–8 buttons.
    EQ settings
    To control Aux Out 1–8 EQ parameters, select the desired Aux Out (1–8) using the corre-
    sponding [SEL] button or fader, then use the buttons and controls in the SELECTED 
    CHANNEL section. The parameters on this page (and the procedure for setting them) are 
    the same as for Input Channels (see page 75).
    Setting Aux Out 1–8 from the Display
    To set Aux Out 1–8 parameters, you can either move the cursor to the desired parameter on 
    the screen and change the value, or operate the desired button or control on the top panel.
    This section explains how to set the parameters on the screen.
    Attenuating Aux Outs
    To attenuate Aux Out 1–8 signals, press the SELECTED CHANNEL EQUALIZER [DIS-
    PLAY] button repeatedly to display the EQ | Out Att page.
    The parameters on this page (and the procedure for setting them) are the same as for Input 
    Channels, except that this page does not include the bit shift parameters (see page 67).Tip:  Refer to Chapter 9 “Input & Output Patching” on page 109 for more information on 
    how to set inserts.
     
    						
    							Setting Aux Out 1–8 from the Display95
    DM1000 Version 2—Owner’s Manual
    8
    Aux Sends
    Delaying Aux Outs
    To delay Aux Out 1–8 signals, press the [ /INSERT/DELAY] button repeatedly until the 
    /INS/DLY | Out Dly page appears.
    The parameters on this page (and the procedure for setting them) are the same as for Input 
    Channels, except that this page does not have the MIX/FB.GAIN parameters (see page 63).
    Comp settings
    To set the Aux Out 1–8 compressors, press the [DYNAMICS] button, then the [F3] button 
    to display the Dynamics | Comp Edit page, and select the desired Aux Out 1–8 by using the 
    corresponding [SEL] buttons or faders.
    The parameters on this page (and the procedure for setting them) are the same as for Input 
    Channels (see page 66).Tip:  You can also display the Out Dly page by pressing the [ /INSERT/DELAY] button once, 
    then selecting the desired Aux Out (1–8) by pressing the corresponding [SEL] button or moving 
    the fader.
     
    						
    							96Chapter 8—Aux Sends
    DM1000 Version 2—Owner’s Manual
    EQ settings
    To set the EQ for Aux Out 1–8, press the EQUALIZER [DISPLAY] button repeatedly to dis-
    play the EQ | EQ Edit page, and use the [SEL] buttons or faders to select Aux Out 1–8.
    The parameters on this page (and the procedure for setting them) are the same as for Input 
    Channels (see page 68).
    Viewing Aux Out settings
    You can view and adjust the parameter settings for the currently-selected Aux Out on the 
    View | Parameter and Fader pages.
    ■Viewing the Compressor and EQ Settings
    To display the View | Parameter page, use the corresponding [SEL] button or fader to select 
    the desired Aux Out (1–8), then press the DISPLAY ACCESS [VIEW] button, then the [F1] 
    button.
    The parameters on this page (and the procedure for setting them) are the same as for Input 
    Channels, except that this page does not include the Gate and Phase parameters (see 
    page 72).
     
    						
    							Setting Aux Out 1–8 from the Display97
    DM1000 Version 2—Owner’s Manual
    8
    Aux Sends
    ■Viewing Faders and On/Off Parameters
    To display the View | Fader page, use the corresponding [SEL] button or fader to select the 
    desired Aux Out (1–8), then press the DISPLAY ACCESS [VIEW] button, then the [F2] but-
    ton.
    •ON/OFF......................... This button turns the currently-selected Aux Out (1–8) on or 
    off. It links with the corresponding [ON] (1–8) button in the 
    Master layer.
    •Fader.............................. This fader sets the currently-selected Aux Out (1–8) level. It 
    links with the corresponding fader (1–8) in the Master layer. 
    The fader knob is highlighted when the fader is set to 0.0dB.
     
    						
    							98Chapter 8—Aux Sends
    DM1000 Version 2—Owner’s Manual
    Setting Aux Send Levels
    You can adjust the level of signals routed from Input Channels to the corresponding Aux 
    Out (1–8). To do this, you can either use the Encoders on the top panel or set the parameters 
    on the screen.
    Using the Encoders
    1Press the AUX SELECT [AUX 1]–[AUX 8] buttons to select the sends.
    2Press the ENCODER MODE [AUX] button.
    When the ENCODER MODE [AUX] button is turned on, you can rotate the Encoders to 
    set Aux Send levels.
    3Select a layer that contains the source Input Channels, then rotate the cor-
    responding Encoders.
    The DM1000 displays the Send level of the currently-selected channel.
    Note:  If rotating the Encoders seems ineffective, check the Mode and Pre/Post parameters on 
    the Aux | Send page (see page 99).
     
    						
    							Setting Aux Send Levels99
    DM1000 Version 2—Owner’s Manual
    8
    Aux Sends
    Setting Send Levels from the Display
    You can view multiple channels’ Aux Send levels on the screen and adjust them individually.
    1Press the AUX SELECT [AUX 1]–[AUX 8] buttons to select the Aux Sends.
    2Press the AUX SELECT [DISPLAY] button repeatedly until the page listed 
    below that contains the desired channels appears.
    -Send1-32 page
    This page displays the Aux Send levels of Input Channels 1–32.
    -Send33-48 page
    This page displays the Aux Send levels of Input Channels 33–48.
    The parameters on these two pages (and the procedure for setting them) are the same.
    •Aux Send rotary controls
    These controls adjust the Aux Send level of the Input Channels. The current numeric levels 
    appear below the rotary controls.
    •PRE/POST
    These buttons enable you to specify the Aux Sends signal source points. The PRE buttons 
    send pre-fader signals, and the POST buttons send post-fader signals.
    •MODE
    Aux Sends have two operating modes that determine how signals are sent: Fixed (Aux Send 
    levels are fixed); and Variable (Aux Send levels are variable).
    •GLOBAL
    The GLOBAL PRE and POST buttons enable you to set all Input Channels for the selected 
    Aux Send to pre-fader or post-fader simultaneously.
    •PRE POINT
    The PRE POINT PRE ON and POST ON buttons enable you to set the pre-fader channels 
    to pre-on (before the [ON] button) or post-on (after the [ON] button).
    Note:  In Fixed mode, Aux Send ON/OFF buttons appear instead of the Aux Send rotary con-
    trols, PRE/POST buttons, GLOBAL PRE/POST buttons, and PRE POINT PRE ON/POST 
    ON. These ON/OFF buttons turn on or off each Input Channel for the currently-selected Aux 
    Send. 
     
    						
    							100Chapter 8—Aux Sends
    DM1000 Version 2—Owner’s Manual
    3Move the cursor to the FIXED or VARIABLE button in the MODE section for 
    the currently-selected Aux Send to select a mode.
    •Fixed Mode
    In this mode, Aux Send levels are fixed at nominal (0.0dB). Also, channel ON/OFF buttons 
    appear instead of the Send level rotary controls and PRE/POST buttons.
    •Variable Mode
    In this mode, Aux Send levels are variable and the signal source point can be either pre-fader 
    or post-fader. Channel Send level rotary controls and PRE/POST buttons appear on the 
    screen.
    Tip:  You can select Variable or Fixed mode individually for each of the eight Aux Sends.
    Note:  
    •In Fixed mode, all ON/OFF buttons are turned OFF.
    •When you switch to Variable mode, the signal source points are set to post-fader (PRE/POST 
    buttons are set to POST), and Send level rotary controls are reset to –∞.
     
    						
    All Yamaha manuals Comments (0)

    Related Manuals for Yamaha Dvx 1000 Owners Manual