Vodavi Starplus Triad S Installation Programming Manual

Speed Dial2-215
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the SPEED flexible button (Button #6). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … System Speed Dialing is enabled at...

2-216Sp ee d Di al
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates....

Speed Dial2-217
Chapter 2 - Features and Operation
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Speed Bins/Chaining
Description
Speed dial bins can be chained together. This is helpful for accessing Long Distance carriers 
or banking services when account codes are required.
Operation
 To chain...

2-218Sp ee d Di al
Chapter 2 - Features and Operation
Print System Speed Numbers
Description
The System Speed Numbers command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
Figure 2-15: System Speed Numbers Printout
Programming Steps
1. Press the SYSTEM SPEED flexible button (FLASH 85, Button #6). The following message 
displays:
2. To print the System Speed bins, press the HOLD...

Station Attributes2-219
Chapter 2 - Features and Operation
Station Attributes
Initialize Station Attributes
Description
The Station Parameters may be initialized setting all data fields to their original, default 
values. The following data fields are returned to their default value upon initializing the 
Station Attributes.
Table 2-17: Station Attribute Defaults
Program 
CodeFlexible
ButtonFeaturesDefault Value
(after initialization)
 FLASH 50 1 Paging Access Enabled
PAGE A 2 Do Not Disturb Enabled
3...

2-220Station Attributes
Chapter 2 - Features and Operation
Programming Steps
1. Press the STATION ATTRIBUTES flexible button (FLASH 80, Button #3). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
FLASH 50
PA G E  B1 Station Identification 006 (24-Btn Keyset)
6 (SLT w/o MW )
2 Station Day Class of Service (COS) COS 1
3 Station Night Class of Service (COS) COS 1
4 Speakerphone/Headset Programming 0=Full Speakerphone
5 Pick-Up Group(s) Programming Group 1
6 Paging...

Station Attributes2-221
Chapter 2 - Features and Operation
Print Station Attributes
Description
The Print Station Attributes command can be used to print specific flexible station 
parameters or to print the entire database in fixed number order.
The Print Station Attributes command can dump the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
When printing the Station attributes the following...

2-222Station Identification
Chapter 2 - Features and Operation
Programming Steps
1. Press the STATION ATTRIBUTES flexible button (FLASH 85, Button #3). The following 
message displays:
2. To print data for:

All stations, press HOLD.

One station, enter the flexible station number, then press HOLD.
Then the following message displays and the requested information prints:
When the system finishes sending the requested information to the printer, a 
confirmation tone sounds.
Station Identification...

Station Identification2-223
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to...

2-224Station Identification
Chapter 2 - Features and Operation
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Station ID Lock
Description
The Station ID Lock feature provides a means for the installer/programmer to lock the station 
ID of all stations in the system. After locked, attempts to plug...