Vodavi Starplus Triad S Installation Programming Manual

Privacy Release2-195
Chapter 2 - Features and Operation
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Preferred Line Answer is enabled on all stations.
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in...

2-196Privacy Release
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO...

Privacy Release2-197
Chapter 2 - Features and Operation
DEFAULT … Privacy is enabled for all CO Lines.
Per Station Option
Description
The system provides privacy on all communications in the system which prevents other 
stations from accidentally entering an existing conversation. However, the system provides 
the ability for a station to join an existing outside CO line conversation (on a per station 
basis). Each station can be granted the privilege to join an existing CO line conversation by 
simply...

2-198Privacy Release
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the PRIVACY flexible button (Button #5). The...

Private Line2-199
Chapter 2 - Features and Operation
Private Line
Description
Private line programming allows certain lines to ring at a specific station only. When placed 
on Hold, these lines are active at the programmed station only. A private line can be 
transferred to other stations, provided the station receiving the call has a loop button or 
direct appearance of that CO line. Refer to “CO Line Group Programming” on page 2-66, “Line 
Group Access - Station” on page 2-64, and “Flexible Button...

2-200Repeat Redial
Chapter 2 - Features and Operation
Repeat Redial
Description
The Repeat Redial feature allows a digital key station to press a flexible button and redial a 
busy or no-answer number after a specific interval. The user is signaled via a queue call back 
indication.
The RPT REDIAL flexible button flashes at the call back rate of 120 ipm for 15 seconds. If the 
station:

Doesn’t answer within the 15 seconds, the call back is canceled. The system retains the 
last call the user made.

Is...

Relay Programming2-201
Chapter 2 - Features and Operation
To activate a redial:
Press the preprogrammed REDIAL flexible button,
-or-
Press the ON/OFF button,
-or-
Lift the handset, line is seized and number is dialed. If the user receives a busy/no answer, 
they may repeat the step to activate another redial.
To cancel the operation:
Press the preprogrammed REDIAL flexible button. A confirmation tone sounds and the Auto 
Redial function is cancelled.

SINGLE LINE TELEPHONE
Not applicable
Conditions
»...

2-202Remote Administration
Chapter 2 - Features and Operation
2. Press the button that corresponds to the desired relay. That button lights. Enter one of 
the following sequences on the keypad:
[1] + [1] = External Page Zone
[2] + [1 through 8] = RAN Start (RAN Announcement Tables 1-8)
[3] + STA # = Loud Bell
[4] + CO # = CO Line Control
[0] =  Disables Relay
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Each time the user presses a relay button, the LCD updates...

Remote System Monitor And Maintenance 2-203
Chapter 2 - Features and Operation
DEFAULT … Modem Answer Timer is set for 25 seconds.
Database Upload/Download
Description
Database Upload/Download provides a maintenance facility which is added to the Remote 
Administration routine. This routine permits downloading of the database to a PC, when a 
software change is made or when the system must be initialized and reprogrammed.
The routine facilitates the programming of a database on an in-house system which...

2-204 Ring Down/Hot Line/Off-Hook Preference
Chapter 2 - Features and Operation
Ring Down/Hot Line/Off-Hook Preference
Description
The Off-Hook Preference feature lets a key station user automatically have a flex button 
selected when going off-hook or when pressing the ON/OFF button. An SLT user may have a 
particular CO line or a CO line group selected automatically when going off-hook. This may 
be established in programming so that key station users can select and/or change their 
off-hook preference...