Vodavi Starplus Triad S Installation Programming Manual

Name / Number Translation Table 2-175
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [55]. The following message displays:
XXX = Table Number 600-799
### = Route Number 000–251
The Route Number LED (Button #1) is lit.
2. Enter a Route Number (000–251) from what was entered in ICLID Ringing Assignments, 
FLASH [43].
To program a phone number into the translation table:
1. Press the PHONE NUMBER flexible button (FLASH 55, Button #2) to enter the desired 
phone number into the...

2-176Night Service
Chapter 2 - Features and Operation
To program a name into the translation table:
1. Press the NAME flexible button (FLASH 55, Button #3) to enter the desired name into 
the translation table. Maximum length is 24 characters. (Refer to  Figure 2-4 on page 2-68 
for dial pad keys.)
2. Press HOLD to update the database. The BACK SPACE flexible button (FLASH 55, 
Button #5) erases the current letter for error correction.
To erase a current phone number/name entry:

Press the CLEAR ENTRY...

Night Service2-177
Chapter 2 - Features and Operation
Digital Voice Mail (DVM) -- The DVM Day/Night Operation can be set up to follow the same 
path as the Day/Night/Special Mode for the telephone system.
Operation
To enter Night Service Mode, from an idle station:
Press the preprogrammed NIGHT SERVICE flexible button [604]. The system is now in the 
Night Service Mode.
To remove Night Service Mode:
Press the preprogrammed NIGHT SERVICE flexible button [604] again. The system is now 
removed from the...

2-178Night Service
Chapter 2 - Features and Operation
3. If no other changes must be made, press HOLD to save the entry. A confirmation tone 
sounds.
Day of Week Programming
Programming Steps
The MONDAY flexible button (Button #2) LED is lit. To change days of the week:
1. Press the appropriate DAY OF WEEK flexible button (FLASH 22, Buttons 2-8).
2. Enter a valid number to indicate the hour and minutes to end night mode.
3. Press HOLD to save the entry. (Example: 07301830 [HOLD]) A confirmation tone...

Off-Hook Signaling2-179
Chapter 2 - Features and Operation
Weekly Night Mode Schedule
A programmable weekly night mode schedule provides for 24 hour, 7 day a week automatic 
night mode operation. The system can be put into and out of night mode automatically on a 
daily basis.
Digital Voice Mail (DVM) -- The DVM Day/Night Operation can be set up to follow the same 
path as the Day/Night/Special Mode for the telephone system.
Conditions
» A station using the night key [604] can put the system into night...

2-180Off-Hook Voice Over
Chapter 2 - Features and Operation
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station...

Off-Hook Voice Over2-181
Chapter 2 - Features and Operation
Operation
To place an Off-hook Voice Over call:
When an OHVO station calls a busy OHVO station and a busy tone is received, the calling 
OHVO station must press a preprogrammed OHVO button [628] to initiate an OHVO 
announcement, and the following occurs:

The HOLD button LED flashes at the called OHVO station.

The OHVO receiving station receives a one-beep warning tone. The station receiving the 
OHVO call must be off-hook and in H or P mode,...

2-182Off-Hook Voice Over
Chapter 2 - Features and Operation
Conditions
» The station must be in H or P mode to enable this feature.
» The station receiving the OHVO call MUST be off-hook and in H mode.
» The receiving station must have OHVO enabled.
» When the receiving station responds via Camp On, all conditions and options available to 
Camp On apply. (Refer to “Camp On” on page 2-48 for more information).
» OHVO may be used to notify the receiving station of a transferred call (CO Line or 
Intercom)...

Outside Calls2-183
Chapter 2 - Features and Operation
Outside Calls
Operation
To answer an outside call:
1. Lift handset or press ON/OFF button.
2. Press slow flashing OUTSIDE LINE button or LOOP button. (If your phone is programmed 
with Preferred Line Answer, you may answer an outside line by lifting the handset or 
pressing the ON/OFF button.)
To make an outside call:
1. Press OUTSIDE LINE or POOL button. ON/OFF button LED lights and dial tone sounds.
2. Dial the desired party.
3. When called party...

2-184Paging
Chapter 2 - Features and Operation
Operation
If you were given the ability to make page announcements:
1. Lift handset or press ON/OFF button.
2. Press preprogrammed PAGE button,
-or-
Dial the paging code.
[700] = All Call - Internal and External
[701- 708] = Internal Zone 1-8
[709] = Internal All Calls
[760 or 761] = External Zone
3. Stations receiving a Page Announcement can press the Volume Bar to change the paging 
volume. The following message displays:

SINGLE LINE TELEPHONE
If you...