Vodavi Starplus Triad S Installation Programming Manual

Ring Down/Hot Line/Off-Hook Preference 2-205
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display...

2-206 Ring Down/Hot Line/Off-Hook Preference
Chapter 2 - Features and Operation
Operation
If your phone has been programmed for Off-Hook Preference, you can access an outside line, 
or a feature by going off-hook or pressing the ON/OFF button. It simulates the depression of 
a specific button and can be programed by a station user or a database administration 
programmer using code [691] + the button number.
While Off-Hook Preference is enabled, you may access internal intercom dial tone as 
follows:
1....

Save Number Redial (SNR)2-207
Chapter 2 - Features and Operation
Save Number Redial (SNR)
Description
Any number dialed on an outside line can be saved permanently and used at any time. This 
number is saved until a new number is stored.
Operation
To save the last number dialed:
1. After placing an outside call, keep handset off-hook.
2. Press the SPEED button twice.
To dial a number that was saved (using the steps above):
1. Press the SPEED button.
2. Dial the [

] button.

System automatically selects...

2-208Single Line Telephone
Chapter 2 - Features and Operation
Single Line Telephone
Compatibility
Description
The Triad-S supports industry standard 2500-type (DTMF) single line telephone (SLT) 
instruments. When the Circuit Single Line Interface Board (CSIB) is installed in the Triad-S, a 
maximum of 24 single telephones can be supported.
SLT DTMF Receiver Timer
Description
Single line telephones require the use of a DTMF receiver when going off-hook and dialing. 
When SMDR or toll restriction (via COS...

Single Line Telephone2-209
Chapter 2 - Features and Operation
Programming Steps
1. Press the SLT HOOK FLASH TIMER flexible button (FLASH 01, Button #14). The following 
message displays:
2. Enter a valid number on the dial pad that corresponds to 0.5-2.0 seconds in 1/10 second 
increments.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … SLT Hook Flash Timer is set at 10 (one second).
SLT Hook Flash Bounce Timer
Description
The SLT Hook Flash Bounce Timer...

2-210Software Version (MPB)
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … SLT Hook Flash Bounce Timer is set to 0.30 seconds.
Software Version (MPB)
Description
The current system software version can be viewed. The display shows the version number 
and level of software.
Operation
To view the Software Version Display:
Dial the S/W Display code [605] on the dial pad. The top line of the LCD shows the 
engineering version...

Speakerphone2-211
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to reflect current...

2-212Sp ee d Di al
Chapter 2 - Features and Operation
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Speakerphone Operation
Description
The Speakerphone feature allows you to conduct a conversation without lifting the handset. 
Speakerphone volume can be adjusted as desired.
Operation
1. Press...

Speed Dial2-213
Chapter 2 - Features and Operation
2. Press the SPEED button and dial speed bin location,
-or-
Press the preprogrammed speed bin button.
To store speed dial numbers:
1. Press the SPEED button once.
2. Press an OUTSIDE LINE button or POOL button.
-or-
Select an outside line by pressing the SPEED button again.
3. Dial the speed bin location.
4. Dial the desired telephone number and include these special codes:

TRANS -- Initiates a Pulse-To-Tone switchover.

HOLD -- Inserts a Pause.

FLASH...

2-214Sp ee d Di al
Chapter 2 - Features and Operation
To store speed dial numbers:
1. Lift handset.
2. Dial [661] on the dial pad.
3. Dial desired station speed number (9000-9019).
4. Dial telephone number to store.
5. Briefly press and release the hookswitch. A confirmation tone sounds.
System Speed Dial Access
Description
Stations can be individually allowed or denied the ability to use system speed dial numbers 
(9020-9099, or 9020-9999 with memory expansion unit). (System speed numbers 9060-9099 
are...