Vodavi Starplus Triad S Description Manual

. . . ...-
Exception Tables
Toll Restriction9-5
3To program Special Tables l-3, it is necessary to associate an area code to the table.
This is done by pressing the appropriate AREA CODE TABLE button and assign the area
code.
Special Table 4 is reserved for the home area code and does not require
an area code entry.
4To display entries in any of the tables, press the DISPLAY TABLES button (FLASH 70,
Button 
#12). Entries in the Allow/Deny tables display two at a time. Entries in the Special
tables...

9-6Exception Tables
Toll Restriction
check for a match in the next Allow or Deny Table to check. The system does not return to the table that
sent the call to the Special Table.
Allow Table
Programming Steps
1Press the ALLOW TABLE A or ALLOW TABLE B flexible button(FLASH 70, Button #lor 
#3). The following message is shown on the display telephone:
ALLOW TABLE A01E02EThe first two bin locations display.
2Enter the 2-digit bin number (01-20) of the bin to be programmed.
It is recommended that:
+Bin 17 be...

Exception Tables
Toll Restriction
example, if [ 1 555 1212] is allowed but [l +I numbers are denied, by an entry into the Deny Table, [l 555
I2 
121 is entered into the Allow Table as an allowed number.
+Allow Table A is referenced and searched first (before Deny Table A) when Station COS is 2 and CO
Line COS is either 1 or 2.
oAllow Table B is referenced and looked at first (before Deny Table B) when Station COS is 3 and CO
Line COS is either 1 or 3.
eWhen Station COS is 4 and CO Line COS is 1 both...

 I
9-8Exception Tables
Toll RestrictionLeading digit [I]: Enter
[BB] [I] [DDD] {S} and/or,
Non-Leading [I]: Enter
WI PW PI
Where:
BB = Bin number (Bin 20)DDD = Do Not Care digit (three entries, MUTE button)
{S} = Search Special Table Command
(TRANS button)
If both leading digit [I] and non-leading digit 
[I] entries are made to
reference the same table, it is necessary to place the leading digit 
[I] entry
ahead of the non-leading digit 
[I] entry in the Allow Table.
Deny Table
Programming Steps
1Press...

 I  -. ..--.
Exception Tables
Toll Restriction
Description
Each Deny Table contains ten bin numbers. Each bin number may be up to eight-digits including {Do Not
4,
t:;-.:F.5Care} digits. Entries in the Deny Table represent numbers or codes that are to be denied or restricted.
0:.Common entries would be [I] for restricting all [ 1 +] type of calls. Exceptions to this restriction would be
entered into the Allow Table.
+Deny Table A is referenced and searched only after the Allow Table A is checked when...

. .9-10Exception Tables
Toll Restriction
1Press the SPECIAL TABLE (#I to #4) flexible button (FLASH 70, Buttons #5 to #8) thatcorresponds to the area code programmed above. The following message is shown on
the display phone:
I
SPECIAL TABLE 1AC XXX
IWhere:
XXX = Area Code
zEnter the 3-digit office codes that are to be allowed followed by a [I] which means to
allow this code. To remove a code from the allow list enter the 3-digit office code
followed by a [0] which removes the code from the allow list....

:
Exception Tables
Toll RestrictionALLOW TABLE ADENY TABLE A
ALLOW TABLE BDENY TABLE B
*n %n O13*DSPECIALSPECIALSPECIAL
SPECIAL
TABLE 1TABLE 2TABLE 3TABLE 4
#lzzTl %n 1172#18AREA CODEAREA CODEAREA CODE
DISPLAY
TABLE 1TABLE 2
TABLE 3TABLES
~lIGIxl+k110 s%lli+I$ 113
lklixi3l1114*lliKxl*116
Programming Steps
1Press the DISPLAY TABLES flexible button (FLASH 70, Button #12) while entering
information into a table.
2While viewing entries made into an Allow or Deny Table, two entries at a time are
displayed on...

9-12Exception Tables
Toll Restriction
While viewing entries in a Special Table, six 3-digit codes allowed display in ascending order starting with
the lowest entry. By pressing the DISPLAY TABLES button again, the next 
6 entries display. This continues
until 
all codes are displayed.
I
SPECIAL TABLE 1AC XXXYYY YYY YYY YYY YYY YYY
IWhere:
XXX= Area Code
YYY= Allowed Office Code
Description
It is possible to view entries in the toll tables using the display on the Executive telephone. To view all
entries,...

Least Cost Routing (LCR) selects the most economical programmed route for an outgoing call, When a
station user dials an outside number, the LCR feature analyzes the number and then automatically chooses
an outside line from the group that has been programmed as most economical, The LCR feature puts the
responsibility of choosing the least expensive route for each area code and exchange code on the system
administrator, not on the station user. In order to make a routing decision, the LCR feature is...

IO-2Least Cost Routing (LCR)
Introduction
If the 6-digit column is marked [yes] in the three digit table entry, the number is then checked in the 6-
digit table. There are twenty 6-digit tables. Each 6-digit table is programmed and becomes associated to a
specific area code with a selected route. Office codes are entered into the 6-digit 
table that is routed to a
specific route list table. This lets the system administrator split area codes for routing to different lines
connected to the system. This...