Vodavi Starplus Triad S Description Manual

Initialize Database Parameters
Introduction
Program
CodeFlex
ButtonFeaturesDefault ValueAfter
Initial~za tion
Flash 1 I
Flash 12l-4System Time And Date
PBX Dialing Codes12 HR MMIDDIYY
None
Flash 13 
( l-41 Executive/Secretary Pairs(  None
Flash 14l-2On Board RelayNone
Flash151Port#I(RS232C MISU)9600Baud
2Port
#2(RS232 MISU)9600Baud
3Port 
#3 (Modem)9600 Baud
Flash201DISA Access Code100
2Database Admin Password3226
Flash211SMDR Enable/DisableDisabled
2Long Distance/Local Assignment
3CharacterPrint...

11-8Initialize Database Parameters
Introduction
Initialize CO Line Attributes
Programming Steps_-.
iPress the CO LINE ATTRIBUTES flexible button (FLASH 80, button #2). The following.cy_. .:,.., . _!. ...Tzmessage displays on the phone:
INITIALIZE CO LINES
PRESS HOLD
.
zTo initialize the CO Line Attributes, press the HOLD button. Confirmation tone is heard.
Description
The CO Line parameters may be initialized setting all data fields to their original, default values. The
following data fields are...

Initialize Database Parameters
Introduction
Program
Code
Page B2Flash 40
Page C
Flex
ButtonFeaturesDefault Value
(after initializa-
tion)1  Preset Call Forward Destination
INone
31 Preset Forward Voice Mail1 None
41  Universal Day AnswerI  Disabled
5Music-On-Hold per CO Line
6Ring Tone
1Flash Timer Programming
2Ring Delay Timer
3Reseize Timer
4Guard Timer
5Preset Forward TimerChannel
100
10
10
1.5 sec.
2 sec.
IO sec.Table 11-2: CO Line Attribute Defaults
STARPLUS Triad-S System Programming ManualIssue I-...

Initialize Database Parameters
Introduction
Initialize Station Attributes
Programming Steps
1Press the STATION ATTRIBUTES flexible button (FLASH 80. button #3). Thefollowing message displays on the phone:
INITIALIZE STATIONS
PRESS HOLD
.
zTo initialize the Station Attributes, press the HOLD button. Confirmation tone is heard.
Description
The Station parameters may be initialized setting all data fields to their original, default values. The
following data fields are returned to their default value upon...

Initialize Database Parameters
Introduction
Program
CodeFlash 50
Page B
Flex
ButtonFeaturesDefault Value
(after initializa-
tion)
1Station Identification
0 (24-Btn Keyset)G(SLT w/o MWt)
21  Station Day Class of Service
I’I
31  Station Day Class of ServiceI’I
4I  Speakerphone/Headset ProgrammingI 1I
5I
I  Pick-Up Group(s) ProgrammingI)I
6Paging Zone(s) Programming1
7Preset Call Forwarding Programming
None
8CO Line Group Access1
9LCR Class of Service (COS)0
10Off -Hook Preference Programming00
(Keyset)
11I...

Initialize Database Parameters
Introduction
Initialize CO / Station Port Parameters
Programming Steps
1Press the PORT-STA/CO flexible button (FLASH 80, button #4). The following
message displays on the phone:
INITIALIZE PORT - STA / CO
PRESS HOLD
.
2To initialize the Station/CO Port Parameters, press the HOLD button. Confirmation
tone is heard.
Description
Station numbers can be initialized and reset to their original default values after the user has performed the
Station Relocation Feature 
(636)....

::
Initialize Database Parameters
IntroductionTable 11-4: Exception Table Defaults
STARPLUS Triad-S System Programming Manualhue I- December 1998 

. .Initialize Database Parameters
Introduction
Initialize System Speed Numbers
Programming Steps
1Press the SYSTEM SPEED NUMBERS flexible button (FLASH 80, button #8). The
following message displays on the phone:
I
INITIALIZE SYS SPEED NO
PRESS HOLD
I
2To initialize the System Speed bins, press the HOLD button. Confirmation tone is heard.
Description
Numbers entered into the System Speed Dial Table may be initialized clearing all bins to their original,
default value (empty). 
All bins 20-99 are cleared...

Initialize Database Parameters
Introduction
9” Insert/Delete Table
+Daily Start Time Table
+:+ Weekly Schedule
+z+ Toll Information Route
II
ProgramFlex
FeaturesDefault Value
CodeButtonAfter 
/n/tlalization
-lash 75LCR TABLES:
13-Digit Area/Off ice Code TableDefault Values assigned
26-Digit Area/Off ice Code TableDefault Values assigned
3Exception Code TableDefault Values assigned
4Route List TableDefault Values assigned
5Insert/Delete Table
Default Values assigned
6Daily Start Time TableDefault Values...

Initialize Database Parameters
Introduction
Initialize ICLID Tables
Programming Steps
IPress the ICLID-DID TABLES flexible button (FLASH 80, button #8). The following
message displays on the phone:
INITIALIZE ICLED
PRESS HOLD
c
2To initialize the ICLID-DID Tables, press the HOLD button. Confirmation tone is heard.
Description
The ICLID Tables parameters may be initialized setting all data fields to their original, default values,
ProgramFlexDefault Value
CodeButtonFeaturesAfter lnlflallzafionFlash...