Vodavi Starplus Triad S Description Manual

DIGITAL STATION OPERATIONForward Override
Forward Override
This feature lets a user reach a busy station that is busy forward, no answer forward or all call forwarded.
This allows the calling station to call a forwarded station, OHVO, Executive Override, Monitor, Message Wait,
Camp On, or Call Back at that station rather than forwarding to the busy destination.
++Dial [ 5# XXX] on the dial pad where XXX is the desired station extension,
Group Listening
All digital key stations have a built-in...

DIGITAL STATION OPERATIONHeadset Mode
Headset Mode
To activate Headset Mode:
+Dial [634] on the dial pad,or
Press pre-programmed* HEADSET MODE button. LED lights steadyWhile Headset mode is active, the ON/OFF button activates the headset
and disables speakerphone and intercom call announce operation at your
station.
NOTE: To install the headset, see the Installation Manual.
To deactivate Headset Mode:
*Dial [634] on the dial pad,
or
Press the pre-programmed* HEADSET MODE button. LED extinguishes.
Station...

DIGITAL STATION OPERATIONICLID Unanswered Call Management Table
ICLID Unanswered Call Management Table
An Unanswered Call Management Table with 100 entry capacity for the Triad-S System is maintained in the
system. The calling number/name information pertaining to any unanswered call is placed in this table at
the time the system determines the call was abandoned.
This table may be accessed from any user station display phone so the unanswered calls may be reviewed and handled
by the end user. Any...

 I
5-48DIGITAL STATION OPERATIONIncoming CO Call Transfer
Incoming CO Call Transfer
This feature lets station users transfer a call that is currently ringing at their station without answering it.
This feature is unavailable to Single Line Telephone users.
While station is idle:
1Call rings in at idle station.
2Press the pre-programmed* INC CO XSFR flexible button,
Of
Dial the Incoming CO call transfer code 
[639] on the dial pad.
3Press a DSS, Group button or dial the 3-digit station number or group...

. .DIGITAL STATION OPERATIONIntercom Buttons5-49
To program a flexible button as an intercom button:
1Press the SPEED button twice.
2Press the desired flexible button to program.
3Dial [645] on the dial pad. Confirmation tone is heard. If an error was made during entry,
error tone is heard.
You place an intercom call to a busy station that has an intercom button:
1The calling station receives ringback tone instead of busy tone. The called station hears
muted or reminder ring and their intercom button LED...

5-50DIGITAL STATION OPERATIONintercom Calling
QUp to five internal parties can be placed on hold. No recall timers apply to Intercom buttons.
Internal callers can be placed and removed from hold when they appear on an Intercom button.
0%To utilize the capability of intercom buttons, busy forward cannot be active at the station.
“PA call ringing to a station on an intercom button and the DND button is pressed, returns DND tone
to the caller and the call is dropped.
*A Flex Button must be programmed for...

DIGITAL STATION OPERATION
Intercom TransferIn the H mode (No LED), you hear two bursts of tone and an announcement, Reply handsfree or lift the handset
for privacy.
6zg2 Intercom Transfer‘2...=t. .
Intercom transfer without DSS buttons:
1Receive or make an intercom call.
2Press the TRANS button. Intercom dial tone is heard.
s Dial the station.
4When the second station answers, you are in a supervised transfer mode (first station is
staged for transfer).
5Hang up (stations 1 and 2 are connected).
Intercom...

5-52DIGITAL STATION OPERATIONLast Number Redial (LNR)
When the telephone is set to the AT command mode, the following AT commands are supported:
+sATD: This is the modem dialing command. The telephone recognizes the ATD and accepts digits
after the command.
-eATH or ATHX: Where X = 0 or 1. This is the modem on hook/off hook command. ATH or ATHO
forces the telephone to the on hook state from it’s current state. ATHl forces the telephone to the
off hook state from it’s current state.
If the handset is off...

DIGITAL STATION OPERATIONLCD Display - Contrast
+If that line is busy, the system automatically selects another line from the same group and
redials the number.
+SIf no lines are available in the same group, the station receives busy tone and can queue for a
line.
9If the station user preselects a line before activating LNR, the preselection overrides the line that
was used originally.
LCD Display - Contrast
There are four contrast adjustments available to the user to adjust the LCD for different...

5-54DIGITAL STATION OPERATIONMailbox Buttons
If an LCR Queue Callback is activated and you wish to cancel that callback request:IDial the LCR Queue Cancel code, 
[626] on the dial pad.
2Replace handset or press ON/OFF button.
Mailbox Buttons
This feature lets station users program specific mailbox index numbers onto flexible buttons at their station
or DSS Console. Users can then transfer internal/external callers to specific Voice Mail Groups or Mailbox
numbers. These Voice Mail Groups or Mailbox...