Vodavi Starplus Sts Key Systems Programming Operation Manual

Direct Inward Dialing2-111
Features and Operation
Name Assigned to DID Number
Programming Steps
1. Press the NAME flexible button (Button #3) to enter the desired name for the DID trunk. 
Maximum length is 8 characters.
2. Press the HOLD button to update the database. A confirmation tone sounds.
3. Use the BACK SPACE flexible button (Button #5) to erase the current letter to correct for 
errors.
DID Name and Number Codes
The display shows the DID name or number as it is entered.
Figure 2-6: DID...

2-112Direct Inward Dialing
Features and Operation
DID/ICLID Ringing Assignments
Description
DID/ICLID Ringing Assignments let you change the ring assignment based on the incoming 
number received. This feature permits you to select from 252 ringing routes for each entry in 
the name to number translation table. For example, this feature could be used to reroute 
selected customers to a specific UCD group and bypass the general Attendant.
Programming Steps
1. Press FLASH and dial [43]. The following...

Direct Inward Dialing2-113
Features and Operation
3. Enter a valid Destination (DDD) or (DDDD) and Ring type (R) followed by HOLD. A 
confirmation tone sounds and the display updates.
* Internal flexible numbers range = 100-8999
Table 2-7: DID/ICLID Ringing Assignments
Valid 3- and 4-Digit Destinations (DDD) and (DDDD) Valid Ring Types (R)
System Speed Bins [9020-9099], for Off-Net Ringing [0] = No Ring; unassigned; or to delete a station
Flexible Extension Numbers* [1] = Day Ring [D]
Flexible Numbers...

2-114Direct Inward Dialing
Features and Operation
View DID/ICLID Ringing Assignments
Description
Keysets designated to ring on an incoming CO line but not designated to ring on the
DID/ICLID ring, may receive a ring cycle before the call is moved. The same ringing 
restrictions applied to CO line ringing are applied to DID/ICLID ringing.
Programming Steps
1. Press Button #17 to display ring assignments. Assignments are displayed in sets of five, 
up to the number programmed. Press Button #17 additional...

Direct Inward Dialing2-115
Features and Operation
3. Press HOLD to change to the different route entered. A confirmation tone sounds.
DEFAULT … No destinations or ringing assignments exist.
DID Digits
Description
The DID Digits option allows the installer to adjust the amount of DID Digits received from 
the CO. This amount is used by all DID trunks in the system.
The DID Translation table can be programmed to determine the number of digits used for 
the routing of a DID call.
Programming Steps
To change...

2-116Direct Inward Dialing
Features and Operation
DID Incoming Signaling
Description
The DID Incoming Signal option allows the installer to determine the type of incoming 
signaling used by all T-1 trunks in the system.
Programming Steps
DTMF is the DID Signaling type used for DID Trunks. Do not change the default setting of 
DTMF unless instructed to do so by technical support.
1. Press the DID INCOMING SIGNALING flexible button (FLASH 41, Button #5) for 
programming the type of DID signaling desired....

Direct Inward Dialing2-117
Features and Operation
DID/TIE Signaling
Description
The DID/TIE Signaling feature can be programmed for one-way direct access inward dialing 
access to specific stations on specific DID lines without going through an Attendant 
answering position.
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD...

2-118Direct Inward Dialing
Features and Operation
DID Collect Timer
Description
The DID Collect Timer is only used when the DID Incoming Signaling is set for dial pulse. This 
is a time-out timer that looks at the incoming digits one digit at a time. If a second digit isn’t 
detected within the 150 ms, the telephone system attempts to process that digit. If a second 
digit is detected, the system waits 150 ms to see if a third digit is received. Otherwise, the 
telephone system attempts to process the...

Direct Inward Dialing2-119
Features and Operation
Initialize DID-TIE Parameters
Description
The DID-TIE Parameters and Timers may be initialized, setting all data fields to their original 
default values.
Programming Steps
1. Press the DID-TIE PARAMETERS flexible button (FLASH 80, Button #13). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
Print DID-TIE Parameters
Description
The Print DID-TIE command dumps the entire database as a permanent record which can 
serve...

2-120 D ire c t In w a rd  Syste m Ac c ess  (D IS A )
Features and Operation
Programming Steps
1. Press the DID-TIE PARAMETERS flexible button (FLASH 85, Button #14). The following 
message displays:
2. To print the DID-TIE Parameters, press the HOLD button. The following message displays:
When the system has finished sending the requested information to the printer, 
confirmation tone sounds.
Direct Inward System Access (DISA)
The STS allows programming of an unlimited number of outside line calls to...