Vodavi Starplus Sts Key Systems Programming Operation Manual

CO Flexible Port Assignment2-61
Features and Operation
6. Enter a valid number on the dial pad (1-7) corresponding to one of seven possible Classes 
of Service to which a station may be assigned.
The seven Classes of Service are:
[1] = COS 1; No restrictions.
[2] = COS 2; Table A governs
[3] = COS 3; Table B governs
[4] = COS 4; Table A and B govern
[5] = COS 5; Restricts [0], [1], [

], [#] dialed as first-digit and places a 7-digit maximum.
[6] = COS 6; Intercom Only (no CO line access - results in a...

2-62CO Flexible Port Assignment
Features and Operation
Programming Steps
If the CO Line numbers need to be relocated to different ports, press FLASH and dial [42]. 
The following message displays:
Buttons 1 through 7 indicate Ports 1 through 28 in increments of 4 ports per button. When 
the relocation program is initially entered, Button #1 is lit to indicate that the user is 
programming the CO Line numbers.
To change the CO Line number assigned to any port:
1. Dial the position number on the display...

CO Line - Access2-63
Features and Operation
CO Line - Access
Description
Through programming, telephones are allowed or denied access to particular outside lines or 
line groups. Refer to “Line Group Access - Station” on page 2-69, “Flexible Button” on page 2-149, 
and “CO Line Group Programming” on page 2-70.
Operation
To access an outside line:
1. Press idle CO line button, POOL button,
-or-
Dial CO line group access code or LCR code: 9, 801-823 or 88+LLL (LLL = CO Line number).
2. Dial desired number...

2-64CO Line Attributes
Features and Operation
CO Line Attributes
Initialize CO Line Attributes
Description
CO Line parameters may be initialized to set all data fields to their original, default values. The 
following data fields are returned to their default value upon initializing the CO Line 
Attributes.
Table 2-4: CO Line Attribute Defaults
Program 
CodeFlexible
ButtonFeaturesDefault Value
(after initialization)
FLASH 40
PA G E  A1 DTMF/Dial Pulse Programming DTMF
2 CO/PBX Programming CO
3 Universal...

CO Line Attributes2-65
Features and Operation
Programming Steps
1. Press the CO LINE ATTRIBUTES flexible button (FLASH 80, Button #2). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
Print CO Line Attributes
Description
The Print CO Line Attributes command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database The system baud rate must match that of the 
printer or receiving device.
When printing the CO Line attributes the...

2-66CO Line Attributes
Features and Operation
Figure 2-3: CO Line Attributes Printout
CO LINE ATTRIBUTES
------------------
CO  001 CO  002
------ ------
DIAL PULSE/DTMF - DTMF DIAL PULSE/DTMF - DTMF
PBX/CO - CO PBX/CO - CO
UNIVERSAL NIGHT ANS - ENABLED UNIVERSAL NIGHT ANS - ENABLED
DISA TRK TO TRK - ENABLED DISA TRK TO TRK - ENABLED
PRIVACY - ENABLED PRIVACY - ENABLED
LOOOP SUPERVISION - 4 LOOOP SUPERVISION - 4
DISA TYPE - NONE DISA TYPE - NONE
LINE GROUP - 1 LINE GROUP - 1
CLASS OF SERVICE - 1 CLASS OF...

CO Line DTMF Sending2-67
Features and Operation
Programming Steps
1. Press the CO LINE ATTRIBUTES flexible button (FLASH 85, Button #2).
2. To print data for:

ALL CO Lines, press the HOLD button.

A specified CO Line Range, enter 6 digits ( 3 digits for the first line and 3 digits for the 
last line in the range):

One CO Line, enter that line twice: [001001]
3. Then press the HOLD button. The following message displays and the CO Line data prints:
When the system finishes sending the requested...

2-68CO Line DTMF Sending
Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO Line Range 
4. Press the DTMF/DIAL PULSE flexible button (FLASH 40, Page A, Button #1).
5. Enter a 0 or 1 that corresponds with the following entries:
[0] = Dial Pulse
[1] = DTMF
6. Press HOLD to save the entry. A confirmation...

CO Line Group2-69
Features and Operation
CO Line Group
Description
Outside lines can be placed in one of twenty-four groups if the customers business requires 
such grouping. Stations are then individually assigned access to these groups and given the 
ability to dial on particular lines.
Line Group Access - Station
Description
A station can access any combination of outside line groups, or a station may not be allowed 
access to outside lines. CO line groups are used primarily by single line telephones...

2-70CO Line Group
Features and Operation
4. Press button #20. The display updates to reflect current programming for Page B.
5. Press the CO LINE GROUP ACCESS flexible button (Button #8). The following message 
displays:
6. To add a Line Group, enter a valid number (00, or 01–23) to designate the outside line 
groups that the station can access, press 1, and then press HOLD to save the entry. A 
confirmation tone sounds and the display updates.
7. To delete a Line Group, enter a valid number (00, or...