Vodavi Starplus Sts Key Systems Programming Operation Manual

CO Line - Incoming Ringing Assignment 2-81
Features and Operation
Seize Timer
Description
The Seize Timer option allows the user to adjust the Seize Timer on a per CO Line basis. The 
Seize Timer is used on ground start type trunks. This Seize Timer is a lead filter timer. The CO 
must provide ground at the tip lead for longer than this timer in order for the system to 
recognize it.
Programming Steps
1. Press the SEIZE TIMER Button (FLASH 40, Page C, Button #7) in the flexible button field. 
The...

2-82 CO Line Loop and Pool Buttons
Features and Operation
4. Press the Page B flexible button (Button #20). The following message displays:
XXX-XXX = CO Line Range
5. Press the TRANSMIT VOLUME flexible button (Button #4). The following message 
displays:
6. Enter a valid number (0-9) for the desired volume level.
7. When the desired level is selected, press HOLD to complete the entry. A confirmation 
tone sounds and the display updates.
DEFAULT … All CO lines are programmed for level 5 (0 dB).
CO Line...

C O L in e Loo p a n d  Po ol Bu tto ns 2-83
Features and Operation
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-149) to be programmed. If only one...

2-84 CO Line Loop and Pool Buttons
Features and Operation
Operation
To make a Loop button:
1. Press the SPEED button twice.
2. Press the desired flexible button.
3. Dial [89].
4. Press HOLD.
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
In-Use Hold (I-Hold) Flash Rate
Description
The In Use-Hold...

CO Line - Loop Supervision2-85
Features and Operation
CO Line - Loop Supervision
Description
The STS can be programmed to monitor CO lines while on-hold or connected to RAN devices 
or Voice Mail systems, or in Trunk-to-Trunk connections for disconnect signal provided by the 
Telco. After a disconnect signal is detected, the STS releases the CO lines and automatically 
place them back in service.
Loop Supervision Programming
Description
Loop Supervision is used primarily with DISA, Voice Mail / Auto...

2-86CO Line - Loop Supervision
Features and Operation
SLT Loop Supervision Programming
Description
Loop Supervision is used primarily with DISA, Voice Mail / Auto Attendant and with 
unsupervised conference applications. It lets the system detect when loop current is broken 
and an outside line is no longer being used. Loop supervision can be disabled on SLT lines so 
that voice mail ports will drop calls when the outside party hangs up.
Programming Steps
1. Press FLASH and dial [50] or dial [51]....

CO Line - Queue2-87
Features and Operation
4. Press button #21. The display updates to reflect current programming for Page C.
5. Press the SLT SUPERVISION button (Button #7). The following message displays:
6. Dial a valid number [0] to disable or [1] to enable SLT Loop Supervision.
7. Press HOLD to save the entry.
DEFAULT … The SLT Loop Supervision setting is [1] (enabled).
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if...

2-88CO Line - Queue
Features and Operation
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-149) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button...

CO Line - Queue2-89
Features and Operation
Operation
If you wish to be placed on a list waiting for an outside line to become available:
1. Press desired busy OUTSIDE LINE button,
-or-
Press the POOL button. (Busy tone sounds.)
2. Press the preprogrammed CO LINE QUEUE button (621).
3. Replace handset or press ON/OFF button.
To answer a queue:
If you hear ringing and an outside line of the line group or a LOOP button you queued onto is 
rapidly flashing:
1. Lift handset or press ON/OFF button.
2. Press...

2-90CO Line - Ringing Options
Features and Operation
CO Line - Ringing Options
Description
When a CO call rings at a busy station, the call rings at the station using a muted ring signal. 
This option allows a user to receive a reminder ring at their busy station, instead of muted 
ringing. A reminder ring timer is also available to provide the reminder ring every time the 
timer expires, as long as the incoming CO line remains connected.
Use Flash 50 programming when you want to modify a range of...