Vodavi Starplus Sts Key Systems Programming Operation Manual

CO Line Group2-71
Features and Operation
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO Line Range
4....

2-72CO Line Group Queuing
Features and Operation
CO Line Group Queuing
Description
The CO Line Group Queuing feature allows trunk group queuing to be turned on (enabled) or 
turned off (disabled) per group. This feature is used only in conjunction with LCR.
Programming Steps
1. Press FLASH and dial [39]. The following message displays:
2. Press button 1-24 to select the desired CO Group to be programmed. The following 
message displays:
3. Dial a 0 or 1 to enable/disable this feature.
[0] = Disabled
[1]...

CO Line - Identification2-73
Features and Operation
CO Line - Identification
Description
The CO Line Identification feature allows entering a name into the database for each 
individual line (trunk) connected to the system. The name may be entered in any 
combination up to 12-characters in length (this represents 24 digits entered). When the CO 
line identification field is programmed, display telephones receive the identification field in 
place of the default field (LINE XXX).
SMDR always print the...

2-74CO Line - Identification
Features and Operation
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press the CO LINE IDENTIFICATION flexible button (Button #11). The...

CO Line - Incoming Ringing Assignment 2-75
Features and Operation
CO Line - Incoming Ringing Assignment
Description
Each CO line may be programmed (in database admin) so that incoming ringing on the 
specified CO line(s) may be assigned initial ringing to one of the following destinations:

One or more stations (Keyset or SLT )

A UCD, Voice Mail, or Hunt Group

Off-Net (via Speed Dial)
The ring-in follows Day Ring assignments unless Night Service mode or Special Ring mode is 
active, in which case all...

2-76 CO Line - Incoming Ringing Assignment
Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press the RING ASSIGNMENT flexible button (Button #10). The display shows the 
following information:
5. Enter a valid Destination (DDD) or (DDDD) and Ring type (R) followed by the HOLD 
button. A...

CO Line - Incoming Ringing Assignment 2-77
Features and Operation
To delete multiple stations:
Enter: DDDD0 HOLD DDDD0 HOLD...etc.
(Example: 10080 HOLD, 10090 HOLD)
DEFAULT … All CO lines ring at the Attendant, Station 100 during Day and Night Modes.
Incoming CO Line Ringing - Setting Flash Rate
Description
The Incoming CO Line Ringing flash rate is the rate at which an Incoming CO line or Loop 
Button flashes. This flash rate can be programmed to 29 different options identified in the 
flash rate table,...

2-78 CO Line - Incoming Ringing Assignment
Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press Button #13 to display ring assignments. Assignments are displayed in sets of six, up 
to the number programmed. The following format displays the assignments.
XDDDD = Destination type ID...

CO Line - Incoming Ringing Assignment 2-79
Features and Operation
Release Timer
Description
The Release Timer option allows the user to adjust the release timer on a per CO Line basis. 
The release timer is used on ground start type trunks.
This timer is a lead filter timer. The CO must remove ground from the tip lead for longer than 
this timer in order for the system to recognize it.
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of...

2-80 CO Line - Incoming Ringing Assignment
Features and Operation
Reseize Timer
Description
The Reseize Timer option lets the user adjust the Reseize Timer on a per CO Line basis. The 
Reseize Timer can be used on any trunk type. This timer sets the time period that a trunk is 
held disconnected after receiving a disconnect before being reseized when a device is 
queued for a member of the trunk group.
Programming Steps
1. Press the RESEIZE TIMER Button (FLASH 40, Page C, Button #5) in the flexible...