Vodavi Starplus Sts Key Systems Programming Operation Manual

Co rd l ess  Ke y Te l eph o n e Un it  Fea t ure  B utt o n 2-101
Features and Operation
To set up a Conference with Personal Park:
1. While connected to an outside line, depress the hookswitch momentarily. The intercom 
dial tone sounds.
2. Dial [438]. The first call is placed in personal park.
3. Dial desired number for second call.
4. Depress the hookswitch momentarily. The Intercom dial tone sounds.
5. Dial [664]. All three parties are conferenced.
6. Hang up to terminate the conference.
Cordless...

2-102 Co rd l e ss Key Te le ph o ne  Un it  Fea tu re  But to n
Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to reflect current programming for Page B.
5. Press the CORDLESS KEY flexible button (Button #17) to assign the FLEX Buttons. The 
following message displays:
XX = Assigned FLEX Button (01-24 = Button...

Database Administration2-103
Features and Operation
Database Administration
Administration Access
Description
The Administration Access feature allows a station to access Database Administration. Each 
station can be enabled/disabled for system programming.
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and dial...

2-104Database Administration
Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the ADMIN ACCESS flexible button (Button #18). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disable
[1] = Enable
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … This feature is disabled....

Database Printout (Dump)2-105
Features and Operation
DEFAULT … Admin Password is set for 3226.
Operation
On the dial pad, press [
][
] plus dial the valid Admin Password. A confirmation tone sounds.
Database Printout (Dump)
Description
Through a system programming command, either portions of or a complete database dump 
can be printed using one of the RS-232C connectors located on the BKSU.
The Print System Database command dumps the entire database as a permanent record 
which can serve as a hardcopy of...

2-106Dial Pulse Sending
Features and Operation
Dial Pulse Sending
Description
Each CO interface circuit for outside lines can be programmed to send dial pulse or DTMF 
signals. Dialing speed and break/make ratios are programmable.
Dial Pulse Parameters
Description
The Dial Pulse option lets the installer adjust the dial pulse ratio and speed when using dial 
pulse (rotary) type signaling. By default, all lines are DTMF (tone) signaling. If pulse dialing is 
required, the individual outside line must be...

Direct Inward Dialing2-107
Features and Operation
Pulse Dial Inter-Digit Timer
Description
This governs the inter-digit time of the Pulse Dial Digits, rotary dial mode. The Pulse Dial Ring 
Timer setting is variable from 300-600 ms.
Programming Steps
1. Press the PULSE DIAL I/D TIMER flexible button (FLASH 02, Button #5). The following 
message displays:
2. Enter a valid number on the dial pad that corresponds to 300-600 ms.
3. Press HOLD to save the entry. A confirmation tone sounds and the display...

2-108Direct Inward Dialing
Features and Operation
If the outside caller disconnects from a two-party conversation, the Central Office opens the 
loop and returns the line to idle state. The STS Digital System detects the disconnect signal, 
release the line, and provides a busy tone to the keyset/SLT (unless the SLT is a VM port), and 
disconnects from the DID line. If the extension called hangs up the phone, the central office 
detects disconnects, and returns the line to the idle state.
When entering...

Direct Inward Dialing2-109
Features and Operation
Route 000 in the DID Ringing Assignment Table is used as the intercept route. Calls to 
numbers not contained in the DID table follow Route 000. If Route 000 is defaulted to None, 
the call follows Route 001.
Route 001 is used as the Busy DID Route. DO NOT program any entries in this Route if you 
intend to provide a busy tone to callers dialing a busy DID/DNIS number.
Programming Steps
Press FLASH and dial [44]. The following message displays:
[RRR] =...

2-110Direct Inward Dialing
Features and Operation
The top left button (ROUTE) in the flexible button field is lit for programming the  Route 
number. The LEDs for the UP Button (Button #18), the DOWN Button (Button #19) is also lit.
To change to a different DID Route Number:
1. Press either the UP Button (Button #18),
-or-
Press the DOWN Button (Button #19).
2. Enter a valid Route Number (000-251) to be associated with the DID Number.
This Route Number is the same Route Number in the ICLID Ringing...