Vodavi Starplus Sts Key Systems Programming Operation Manual

Executive Override2-141
Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the EXECUTIVE OVERRIDE flexible button (Button #4). The following message 
displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Executive Override is...

2-142Executive Override
Features and Operation
» When the Executive joins an intercom call or CO call and the Executive is not in a mute 
state, and any member of the party hangs up, the call is converted to a two-party 
conversation.
» When the Executive joins an intercom call or CO call and the Executive is in the mute 
state, and either of the two parties in the intercom call hang up, the call is dropped. If the 
Executive hangs up, the call remains a two-party conversation.
» Certain forwarding types...

Executive Override2-143
Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the EXECUTIVE OVERRIDE BLOCK flexible button (Button #13). The following 
message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Executive Override...

2-144Executive Override
Features and Operation
Programming Steps
1. Press the EXEC OVER WARN TONE flexible button (FLASH 05, Button #4).
2. Enter a valid number (0 or 1) that corresponds with the following entries:
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Executive Override Warning Tone is enabled.
Barge-In Warn Tone
Description
When the Barge-in Warn Tone feature is enabled, it produces a tone to notify a station that 
another station is about...

Executive/Secretary Pairs2-145
Features and Operation
DEFAULT … Barge-in Warn Tone is enabled.
Executive/Secretary Pairs
Description
There are four Executive/Secretary pairs available. When an Executive station is busy or in 
DND, intercom calls and transfers are automatically routed to the designated Secretary.
The assigned secretary may Camp On to the Executive Station when the station is busy or in 
Do-Not-Disturb. There can be only one pairing of stations, with no duplicates. You cannot 
pair...

2-146External Day Ring
Features and Operation

To program a fourth pair, press the fourth button in the flexible button field and enter 
station numbers as in steps 2-5.
DEFAULT … No Executive/Secretary pairs are assigned.
Conditions
» If you are designated the Executive station and your phone is busy or in DND, all calls are 
routed to the Secretary station.
» If you are the designated Secretary station, you can signal the Executive that is busy or in 
DND by using the Camp On feature.
External Day...

External Night Ring2-147
Features and Operation
External Night Ring
Description
When outside lines are marked UNA, ringing activates a tone over external paging when an 
incoming call occurs on those lines during night service.
Programming Steps
1. Press the EXT NIGHT RING flexible button (FLASH 05, Button #3).
2. Enter a valid number (0 or 1) that corresponds with the following entries:
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … External Night...

2-148Flash Rates (Programmable)
Features and Operation
Flash Rates (Programmable)
Description
Fixed and flexible button flash rates can be programmed. Nineteen features/functions can be 
programmed to use on of 14 different red or 14 different green flash rate options. These are 
set up in FLASH 07 of admin programming. Refer to section that covers the feature/function 
for the detailed programming steps.
All other flash rates in the system are fixed (defaulted).
When in FLASH 07, the buttons on the...

Flexible Button Assignment2-149
Features and Operation
Flexible Button Assignment 
Description
If you have buttons on your telephone, you may program them to suit your own needs. This 
feature also allows programming of flexible buttons from a remote location (off-site). Range 
programming can also assign these buttons to multiple stations.
The possible functions you may assign to these buttons include:

Outside Line -- Automatically accesses assigned line. (User programmable)

DSS/BLF -- Automatically...

2-150Flexible Button Assignment
Features and Operation
To assign a CO Line Button:
Enter [BB], [1], [LLL], [HOLD]
LLL = CO Line Number
Buttons assigned as specific CO lines provide 
direct access and appearance of the CO line at 
a station. The station receives call status 
indications such as LED flash rates for 
incoming ringing when the line is placed on 
HOLD, etc. CO Line ringing is programmed in 
CO Line Attribute programming.
To assign a Loop Button:
Enter [BB], [2], [HOLD]
Used for a station...