Vodavi Starplus Sts Key Systems Programming Operation Manual

Directory Dial2-131
Features and Operation
Programming Steps
1. Press the DIRECTORY DIAL TABLE flexible button (FLASH 85, Button #10). The following 
message displays:
2. To print the Directory Dialing Table parameters, press the HOLD button. The following 
message displays:
When the system finishes sending the requested information to the printer, a 
confirmation tone sounds.
Dial-By-Name
Description
The system allows station users to dial extension numbers, or speed bins, by entering the 
name of a...

2-132Distinctive Ringing
Features and Operation
EXAMPLE -- To search for the name BROWN, press [2][7][6][9][6].

When the system finds a unique numeric match to the name being dialed, the call is 
placed to the station matching the name.

The intercom call signals the station according to the H-T-P button.

If fewer than 8 digits are dialed, the numeric match is dialed after a 10-second 
interdigit time-out occurs, or if [#] is pressed.
Conditions
» The system dials the station that matches the dialed...

Distinctive Ringing2-133
Features and Operation
4. Press the Page B flexible button (Button #20). The following message displays:
XXX-XXX = CO Line Range
5. Press the RING TONE flexible button (Button #9). The following message displays:
6. Enter a valid number on the dial pad to change this feature.
7. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … Ring Tone is set for 00 (697/770).
XXX - XXX  PAGE  B
ENTER  BUTTON  NUMBER
RING  TONE 00-36
00
Table 2-11:...

2-134Distinctive Ringing
Features and Operation
Enabling/Disabling Distinctive Ring Tone
Description
The distinctive ring tone feature must be enabled and disabled in admin programming.
Programming Steps
1. Press the CO RING TONE flexible button (FLASH 06, Button #2). The following message 
displays:
2. Enter a 0 or 1 on the dial pad to enable/disable the tone ring signal.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … CO Ring Tones is enabled.
Ring...

Distinctive Ringing2-135
Features and Operation
The ringing choices are as follows:
Conditions
» Station users may listen to all tones by dialing the 2-digit codes one after another. The 
tone that is sounding when the SPEED button is pressed is saved as that station’s tone 
ringing selection.
» A station’s tone ringing selection is maintained in a battery protected area of memory. 
Therefore, if a system experiences a power failure or a soft or hard restart, the tone 
ringing selection is restored.
»...

2-136Do Not Disturb
Features and Operation
Do Not Disturb
Description
Placing a keyset in Do Not Disturb (DND) eliminates incoming outside line ringing, intercom 
calls, transfers and paging announcements. A ringing station may go into DND to silence 
ringing. The Attendant can override a station in DND. Stations in DND can continue to make 
normal outgoing calls.
Stations can be individually allowed or denied the ability to place their telephone in Do Not 
Disturb. By default, Do Not Disturb is enabled...

Do Not Disturb2-137
Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the DO NOT DISTURB flexible button (Button #2). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Do Not Disturb is enabled at all...

2-138Do Not Disturb
Features and Operation
Conditions
» Calling stations receive a DND audible tone.
» Attendants do not have DND capability.
» DND capability is programmable on a per-station basis.
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
One-Time Do Not Disturb
Description
Prevents calls from ringing...

Executive Override2-139
Features and Operation
Do Not Disturb - DSS/BLF Flash Rate
Description
The Do Not Disturb DSS/BLF flash rate is the rate at which a DSS button of a station flashes 
when you are in a Do Not Disturb mode. This flash rate can be programmed to 29 different 
options identified in the flash rate table. This enables the programmer to customize the key 
system configuration to desired flash rates.
Programming Steps
1. Press the DND – DSS/BLF flexible button (FLASH 07, Button #6). The...

2-140Executive Override
Features and Operation
Executive Override - Enable/Disable
Description
This system programmable option enables or disables a warning tone when the station 
marked as an executive is cut-thru to the conversation. This is useful for UCD agent 
supervisors or training personnel who require a service observing option.
A separate condition has been added to this feature which allows or disallows an Executive to 
override an extension. This prevents an extension with override capability...