Vodavi Starplus Hybrid Key Telephone System Installation Manual

sTARPLUS@ SPD 1428 & 2856 Digital Key Telephone Systems 
PAGE “B” STATION ATTRIBUTES (Cont’d) 
N. Speakerphone Programming 
Programming Steps 
1. Press the SPEAKERPHONE flexible button 
(Page B, Button #3). 
2. Enter a one-digit number between 0 and 3 to 
identify the speakerphone operation. 
0 = works as normal speakerphone. 
Full speakerphone capabilities on 
both CO lines and Intercom. 
1 = Speakerphone enabled for intercom 
calls only. Speakerphone capabilities 
disabled for outgoing CO line calls...

PAGE “B” STATION AnRlBUTES (Cont’d) 
P. Paging Zone(s) Programming 
Programming Steps 
1. Press the PAGING ZONES flexible button 
(Page B, Button #5). 
2. Enter a one-to-four digit number to program 
paging zone(s). 
, 0= no zone (no pages received) 
l= Zone 1 
2= Zone 2 
3= Zone 3 
4= Zone 4 
3. Press HOLD button. Display will now update. Description 
PAGING ZONES. Each station is assigned to inter- 
nal paging zones. A station can be in any or all zones 
or in no zone at all. 
All Call is all page...

sTARPLUS@ SPD 1428 & 2858 Digital Key Telephone Systems 
PAGE “B” STATION ATTRIBUTES (Cont’d) 
Q. Preset Call Forward Programming 
Programming Steps 
1. Press the PRESET FORWARD flexible button 
(Page B, Button #6). 
2. Enter a three-digit number to determine the 
destination where calls are to be routed when 
the preset forward timer expires. 
Valid 3 diait destinations are: 
020-099= System Speed Bins 20-99 for off-net 
forwarding 
100-155= Station Numbers 
330~337= Hunt Groups l-8 
440~447= Voice Mail...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2856 
PAGE “B” STATION AlTRIBUTES (Cont’d) 
R. CO Line Group Access 
Programming Steps 
1. Press the CO LINE GROUP ACCESS flexible 
button (Page B, Button #7). 
2. Enter up to seven digits (0, or 1-7) for the 
outside line groups the station will have access 
to. 
0 =no access 
1 =access to Group 1, Code 9 or 81 
2 =access to Group 2, Code 82 
3 =access to Group 3, Code 83 
4 =access to Group 4, Code 84 
5 =access to Group 5, Code 85 
6 =access to Group...

PAGE “B” STATION AmRlBUTES (Cont’d) 
T. Off-Hook Preference Programming 
Programming Steps 
To program a station for Off-Hook Preference; 
1. Press the OFF-HOOK PREF flexible button 
(Page B, Button #9). The following message is 
shown on the display phone: 
2. Enter the two-digit button number (01-28) or 
(00) to indicate no specific button is preferred. 
SLT’s use 01 to enable or 00 to disable. 
3. Then, enter either 0 or 1 where: 
0 = Disable user programmable preference 
so that users may not change...

Digital Key Telephone Systems STARPLUS@ SPD 1428 & 2856 
PAGE “B” STATION ATTRIBUTES (Cont’d) 
U. Flexible Button Programming 
Programming Steps 
1. Press the BUTTON ASSIGN flexible button 
(Page B, Button #lo). The following message 
is shown on the display phone: Description 
BUTTON ASSIGN. Each 34 Button Digital terminal 
has 28 flexible buttons which can be individually 
programmed. One of the following five (5) operations 
can be selected in programming for each button. 
, 2. Enter the two-digit...

STARPLUS@ SPD 1428 & 2856 Digital Key Telephone Systems 
PAGE “B” STATlON ATTRIBUTES (Cont’d) 
Flexible Button Programming (Cont’d) 
Programming Steps 
If SLT stations are to be programmed for Off-Hook 
Preference, it is necessary to program the desired 
CO line, or CO line group, the SLT is to access when 
going off-hook. 
To assign a CO Line for a SLT with Off-Hook Pref- 
erence, enter: 
00 [l] LL HOLD (LL= CO Line 01-28) 
To assign a CO Line group for an SLT with Off-Hook 
Preference, enter: 
00 [3] G...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2856 
PAGE “B” STATION AlTRIBUTES (Cont’d) 
V. Display Flexible Buttons 
Programming Steps 
If the flexible buttons are to be viewed: 
1. Press the DISPLAY BUTTONS flexible button 
(Page B, Button #17). The programming as- 
signment on four buttons will be displayed start- 
ing with the lowest button number. With each 
sub-sequent depression of the DISPLAY BUT- 
TONS button, the next four buttons will be 
displayed. The following message is shown on 
the...

STARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
SECTION 640 
DISTRIBUTION (UCD)  UNIFORM CALL 
640.1 
UCD GROUP PROGRAMMING 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. Refer to Sec. 600.2. 
If UCD Groups are to be assigned: 
1. Press FLASH and dial [60]. The following mes- 
sage is shown on the display phone: 
Where: 
XX= RAN Announcement Table(s) 
A/VI= Alternate UCD Group Assignment...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2888 
UNIFORM CALL DISTRIBUTION (Cont’d) 
6. Overflow Station Assignment 
Programming Steps 
To program UCD Overflow station: 
1. Press the OVERFLOW ASSIGN flexible button 
(Button #lo). 
2. Enter the three-digit station number (100 to 
155) to designate the UCD Groups overflow 
station. 
3. Press the HOLD button to enter the data. 
, 
C. UCD Station Assignment(s) 
Programming Steps 
To program stations into a UCD group: 
1. Press the STATION ASSIGN...