Vodavi Starplus Hybrid Key Telephone System Installation Manual

LCR PROGRAMMING (Cont’d) 
L. Default LCR Data Base 
Programming Steps Description 
In an effort to decrease installation and set up time, 
usually associated with LCR, a default LCR data 
base has been incorporated. The default LCR data 
base will provide basic routing for local and long 
distance dialing. Default entries have been made in 
the Three Digit Table for local office codes (NNX’s) 
and all area codes (NPA’s). Two routes have been 
established with the default data base for routing of 
all...

sTARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
SECTION 660 
-  INITIALIZE DATA BASE PARAMETERS 
A. Introduction 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.2). 
If Data Base Parameters need to be initialized: 
1. Press FLASH and dial [80]. The following mes- 
sage will be shown on the display of a display 
phone: Description 
This section describes the procedures...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2866 
Initialize Data Base Parameters 
B. Initialize System Parameters 
Programming Steps 
If System Parameters need to be initialized: 
1. Press the System Parameters flexible button 
(Button #l). The following message will be 
shown on the display phone: Description 
The system parameters may be initialized setting all 
data fields to their original, default values. The fol- 
lowing data fields are returned to their default values 
upon initializing...

Initialize Data Base Parameters (Cont’d) 
Initialize System Parameters (Cont’d) 
, 
Programming Steps Description 
Issue 1, November 1991 660-3  

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2656 
Initialize Data Base Parameters (Cont’d) 
C. initialize CO Line Attributes 
Programming Steps 
If CO tine Attributes need to be initialized: 
1. Press the CO Line Attributes flexible button 
(Button #2). The following message will be 
shown on the display phone: Description 
The CO Line parameters may be initialized setting 
all data fields to their original, default values. The 
following data fields are returned to their default 
value upon...

sTARPLUS@ SPD 1428 & 2858 Digital Key Telephone Systems 
Initialize Data Base Parameters (Cont’d) 
D. Initialize Station Attributes 
Programming Steps 
If Station Attributes need to be initialized: 
1. Press the Station Attributes flexible button (But- 
ton #3). The following message will be shown 
on the display phone: Description 
The Station parameters may be initialized setting all 
data fields to their original, default values. The fol- 
lowing data fields are returned to their default value 
upon...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2868 
1 
ZAMP ON 
DND 
CONF 
HTP 
7, r SPKRVOL 
FUNGVOL 
Figure 660-l Default Button Mapping 
660-6 
Issue 1, November 1991  

Initialize Data Base Parameters (Cont’d) 
E. Initialize Group Parameters 
Programming Steps 
If Group Parameters need to be initialized: 
1. Press the Group Parameters flexible button 
(Button #4). The following message will be 
shown on the display phone: Description 
Hunt, UCD and Voice Mail Group parameters may 
be initialized setting all data fields to their original, 
default values. The following data fields are returned 
to their default value upon initializing Group parame- 
ters: 
2. To...

Initialize Data Base Parameters (Cont’d) 
F. Initialize Toll Tables 
Programming Steps 
If Exception Tables need to be initialized: 
1. Press the Toll Tables flexible button (Button 
#5). The following message will be shown on 
the display phone: Description 
The Toll Table parameters including the Allow/Deny 
Tables and the Special Tables may be initialized 
setting all tables to their original, default values. The 
following Tables are cleared returning to their default 
value upon initializing the...

STARPLUS@ SPD 1428 & 2856 Digital Key Telephone Systems 
Initialize Data Base Parameters (Cont’d) 
G. Initialize System Speed 
Programming Steps Description 
If System Speed bins need to be initialized: 
1. Press the System Speed flexible button (Button 
#6). The following message will be shown on 
the display phone: 
2. To initialize the System Speed bins, press the 
HOLD button. Confirmation tone will be heard. Numbers entered into the System Speed dial Table 
may be initialized clearing all bins to...