Vodavi Starplus Hybrid Key Telephone System Installation Manual

sTARPLUS@ SPD 1428 & 2858 
Digital Key Telephone Systems 
840.2 UCD TIMERS 
Programming Steps 
If UCD timers are to be changed: 
a. Press FLASH and dial [Sl]. The following mes- 
sage is shown on the display phone: Description _ 
Four timers for UCD operation are programmable on 
a system-wide basis. The UCD timers include: A 
Ring Timer, Message Interval Timer, an Overflow 
Timer, a Auto Wrap-Up Timer, and No/Answer 
Timer. Each timer is described below: 
Related Programming: UCD Group Assignments;...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2666 
UCD TIMERS (Cont’d) 
B. UCD Message Interval Timer 
Programming Steps 
To make a change to the UCD Message Interval 
Timer: 
1. Press the MIT TIMER flexible button (Button 
w. 
2. Enter the three-digit timer value on the dial pad 
which corresponds to.OOO-600 seconds. 
Press HOLD button. Display will now update. 
NOTE: The UCD Ring and Message Interval Timers 
4 only apply when RAN ports have been specified. If 
RAN ports are not specified,...

UCD TIMERS (Cont’d) 
E. UCD No-Answer Timer 
Programming Steps 
Description 
To make a change to the UCD No-Answer Timer: 
1. Press the NO-ANSWER TIMER flexible button 
(Button #5). 
2. Enter the three-digit value on the dial pad which 
corresponds to 000-300 seconds. 
3. Press HOLD button. Display will now update. NO-ANSWER TIMER. After a UCD call rings to an 
agent, this timer takes effect. If the agent does not 
answer the call before this timer expires, then that 
agent is set to “UCD Unavailable”...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2866 
640.3 UCD RAN ANNOUNCEMENT TABLES 
Programming Steps 
If Recorded Announcement devices are installed to 
operate with UCD, these tables must be pro- 
grammed: 
a. Press FLASH and dial [62]. The following mes- 
sage is shown on the display phone: 
, b. The top left button in the flexible button field will 
be lit for programming UCD RAN An- 
nouncement Table 1. To change to UCD RAN 
Announcement Table 2, press flexible button 
#2. 
c. Enter a string...

mARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
SECTION 645 
VOICE MAIL GROUPS (VM) 
645.1 VOICE MAIL PROGRAMMING 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.2). 
If Voice Mail Groups are to be programmed: 
1. Press FLASH and dial t65]. The following mes- 
sage is shown on the display phone. 
2. Where: 
G= Voice Mail group number (O-7) 
AAA= Alternate group (440447)...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2866 
VOICE MAIL GROUPS (Cont’d) 
A. Alternate Voice Mail Group 
Programming Steps 
To program an alternate group: 
1. Press the ALTERNATE VM GP flexible button 
(Button #9). 
2. Enter the three-digit pilot number (440 to 447) 
of the desired group. 
3. Press the HOLD button to enter data. 
B. 
“Leave” Mail Index Entry 
Programming Steps 
To specify the “Leave” mail index (outpulsing table) 
to be accessed by a Voice Mail group: 
1. Press the LEAVE...

STARPLUS@ SPD 1428 & 2858 
Digital Key Telephone Systems 
VOICE MAIL GROUPS (Cont’d) 
D. Station Assignment(s) 
Programming Steps 
To program the stations in the Voice Mail group: 
1. Press the STATION ASSIGN flexible button 
(Button #12). 
2. Enter the three digit station numbers. A maxi- 
mum of eight SLT stations may be entered. 
3. Press the HOLD button to enter the data. Description 
Up to eight (8) SLT or OPX port extension numbers 
may be programmed into a Voice Mail group. 
The ports will be...

Digital Key Telephone Systems mARPLUS@ SPD 1428 & 2666 
848.2 VOICE MAIL OUTPULSING TABLE 
A. Voice Mail In-Band Signaling: 
Programming Steps 
If Voice Mail In-Band signalling is to be used: 
1. Press FLASH and dial [88]. The following mes- 
sage is shown on the display phone. 
Where: 
y = the table index (O-7) 
x = entered digits (O-9, #, 
l , Pauses) 
2. The TABLE 1 flexible button (Button #l) led is 
lit. 
To change tables, press the appropriate flexible 
button (Buttons 2-8) and perform the...

sTARPLUS@ SPD 1428 & 2856 Digital Key Telephone Systems 
VOICE MAIL OUTPULSING TABLE (Cont’d) 
B. 
1. 
2. 
3. 
Voice Mail Disconnect Table: 
Programming Steps 
Press the DISCONNECT TABLE 8 flexible but- 
ton (Button #$I) . This is the table number used 
for the Voice Mail disconnect signal. 
Enter up to 12 digits which will be used for the 
disconnect signal, including ‘*’ and ‘Y. TRAN 
button = pause. 
Press the HOLD button. Display will now up- 
date. Description 
To avoid Voice Mail ports from being...

Digital Key Telephone Systems 
645.3 VOICE MAIL IN-BAND DIGITS 
Programming Steps 
Description 
If Voice Mail ID digits are to be enabled or disabled 
for Incoming CO callers: 
1. Press FLASH and dial [671. The following mes- 
sage will be shown on the display: The Starplus Digital (SPD) Key Telephone System 
allows the system to be programmed so that if a 
station programmed to receive incoming CO line 
ringing is forwarded to Voice Mail they may have 
direct incoming callers routed directly into their...